set clock TOYOTA RAV4 2006 Service Repair Manual

EM–562GR-FE ENGINE MECHANICAL – ENGINE UNIT
EM
25. REMOVE NO. 1 CHAIN SUB-ASSEMBLY
(a) Turn the crankshaft counterclockwise 10
to loosen
the chain of the crankshaft timing gear.
(b) Remove the chain from the crankshaft timing gear
and place it on the crankshaft.
(c) Turn the camshaft timing gear on the RH bank
clockwise (approximately 60
) and set it as shown in
the illustration. Be sure to loosen the chain between
the center banks.
(d) Remove the chain.
26. REMOVE IDLE SPROCKET ASSEMBLY
(a) Using a 10 mm hexagon wrench, remove the No. 2
idle gear shaft, idle sprocket and No. 1 idle gear
shaft.
27. REMOVE NO. 1 CHAIN VIBRATION DAMPER
(a) Remove the 2 bolts and vibration damper.
28. REMOVE NO. 2 CHAIN VIBRATION DAMPER
(a) Remove the 2 chain vibration dampers.
29. REMOVE CRANKSHAFT TIMING GEAR OR
SPROCKET
(a) Remove the pulley set bolt.
(b) Remove the crankshaft timing gear from the
crankshaft.
(c) Remove the 2 pulley set keys from the crankshaft.
A132114E01
A132098E01
A129695
A132136
A131972

EM–1242GR-FE ENGINE MECHANICAL – ENGINE UNIT
EM
(b) Turn the camshaft timing gear on the bank 1
counterclockwise to tighten the chain between the
banks.
NOTICE:
If reusing the idle sprocket, align one of the idle
sprocket's chain plate marks with one of the
chain's chain plates when installing the idle
sprocket.
(c) Align the mark plate and timing mark as shown in
the illustration and install the chain onto the
crankshaft timing gear.
HINT:
The chain mark plate is yellow.
(d) Temporarily tighten the pulley set bolt.
(e) Turn the crankshaft clockwise to set it to the bank 1
block bore center line (TDC / compression).
35. INSTALL CHAIN TENSIONER SLIPPER
(a) Install the chain tensioner slipper.
A122184E05
A132116E01
A132112E01

SB–6SEAT BELT – SEAT BELT WARNING SYSTEM
SB
OPERATION CHECK
1. INSPECT DRIVER SIDE SEAT BELT WARNING LIGHT
(a) Turn the ignition switch ON.
(b) When the driver seat belt is not fastened, check that
the driver seat belt warning light on the combination
meter blinks.
(c) When the driver seat belt is fastened, check that the
driver seat belt warning light on the combination
meter is off.
2. INSPECT PASSENGER SIDE SEAT BELT WARNING
LIGHT (For Automatic Air Conditioning System)
(a) Turn the ignition switch ON.
(b) When the front passenger seat belt is not fastened
with the passenger seat occupied, check that the
front passenger seat belt warning light on the heater
control panel display blinks.
(c) When the front passenger seat belt is fastened with
the passenger seat occupied, check that the front
passenger seat belt warning light on the heater
control panel display is off.
3. REMOVE PASSENGER SIDE SEAT BELT WARNING
LIGHT (For Manual Air Conditioning System)
(a) Turn the ignition switch ON.
(b) When the front passenger seat belt is not fastened
with the passenger seat occupied, check that the
front passenger seat belt warning light on the clock
panel blinks.
(c) When the front passenger seat belt is fastened with
the passenger seat occupied, check that the front
passenger seat belt warning light on the clock panel
is off.
4. INSPECT SEAT BELT WARNING BUZZER
HINT:
If the buzzer does not sound, the buzzer cancel setting
may be set to ON.
(a) Turn the ignition switch ON.
(b) When the vehicle is driven at approximately 20 km/h
(12.4 mph) or more while the driver or front
passenger seat belt is not fastened, check that the
buzzer in the combination meter sounds at 1.2
second intervals for 30 seconds.
(c) 30 seconds after the buzzer has first sounded,
check that the buzzer sounds at 0.4 second
intervals for 90 seconds.
(d) 120 seconds after the buzzer has first sounded,
check that the buzzer stops.
(e) After the buzzer has stopped, turn the ignition
switch off and then start the engine again. Drive the
vehicle at approximately 25 km/h (16 mph) or more
while the driver or front passenger seat belt is not
fastened, and then check that the buzzer sounds
again.