check engine TOYOTA SEQUOIA 2001 Service Repair Manual

± DIAGNOSTICSENGINE
DI±171
365 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check air induction system (See page SF±1).
CHECK:
Check the air induction system for vacuum leaks.
NG Repair or replace air induction system.
OK
4 Perform active test (A/F control).
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and turn the tester ON.
(c) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
(d) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST /
A/F CONTROL.
(e) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT
button to change the fuel injection volume).
(f) Monitor the voltage outputs of A/F and HO2 sensors(AFS B1S1 (AFS B2S1) and O2S B1S2 (O2S
B2S2)) displayed on the tester.
HINT:

The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
Standard:
Tester Display
(Sensor)Injection VolumesStatusVoltages
AFS B1S1 (AFS B2S1)
(A/F)+25 %RichLess than 3.0
AFS B1S1 (AFS B2S1)
(A/F)±12.5 %LeanMore than 3.35
O2S B1S2 (O2S B2S2)
(HO2)+25 %RichMore than 0.55
O2S B1S2 (O2S B2S2)
(HO2)±12.5 %LeanLess than 0.4
Result:
Status
AFS B1S1
(AFS B2S1)Status
O2S B1S2
(O2S B2S2)A/F Condition and
A/F Sensor ConditionMisfiresSuspected Trouble AreasProceed To
Lean/RichLean/RichNormal''C
LeanLeanActual air±fuel ratio leanMay occur

PCV valve and hose

PCV hose connections

Injector blockage

Gas leakage from exhaust system

Air induction system

Fuel pressure

Mass Air Flow (MAF) meter

Engine Coolant Temperature (ECT)
sensor
A

DI±172
± DIAGNOSTICSENGINE
366 Author: Date:
2005 SEQUOIA (RM1146U)Rich
RichActual air±fuel ratio rich'

Injector leakage or blockage

Gas leakage from exhaust system

Ignition system

Fuel pressure

MAF meter

ECT sensor
A
LeanLean/RichA/F sensor malfunction'
A/F sensorB
RichLean/RichA/F sensor malfunction'
A/F sensorB
Lean: During A/F CONTROL, the A/F sensor output voltage (AFS) is consistently more than 3.35 V, and the
HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
Rich: During A/F CONTROL, the AFS is consistently less than 3.0 V, and the O2S is consistently more than
0.55 V.
B Go to step 11.
C Go to step 15.
A
5 Read value of engine coolant temperature.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / COOLANT
TEMP.
CHECK:
(a) Read the COOLANT TEMP twice, when the engine is cold and also when warmed up.
Standard:
With cold engine: Same as ambient air temperature.
With warm engine: Between 75C and 95C (167F and 203F)
NG Replace engine coolant temperature sensor.
OK

± DIAGNOSTICSENGINE
DI±173
367 Author: Date:
2005 SEQUOIA (RM1146U)
6 Read value of mass air flow meter.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / MAF and
COOLANT TEMP.
(d) Allow the engine to idle until the COOLANT TEMP reaches 75C (167F) or more.
CHECK:
(a) Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
Standard:
MAF while engine idling: Between 1.4 gm/s and 2.3 gm/s (shift position: N, A/C: OFF).
MAF at engine speed of 2,500 rpm: Between 5.4 gm/s and 7.9 gm/s (shift position: N, A/C: OFF).
NG Replace mass air flow meter.
OK
7 Check fuel pressure (See page SF±7).
CHECK:
Check the fuel pressure (high or low pressure).
NG Check and replace fuel pump, pressure regula-
tor, fuel pipe line and filter (See page SF±1).
OK
8 Check exhaust system for gas leakage.
OK:
No exhaust gas leakage.
NG Repair or replace exhaust gas leakage point.
OK

B17396
HT +B
AF± AF+ Sensor 1A/F Sensor Component Side:
Front View
DI±174
± DIAGNOSTICSENGINE
368 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check for spark and ignition (See page IG±1).
HINT:
If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read
with the hand±held tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MIS-
FIRE / CYL#1 (to CYL#8).
NG Repair or replace ignition system.
OK
10 Check injector injection (See page SF±29).
HINT:
If the injectors malfunction, engine misfires may occur. The misfire counter can be read with the hand±held
tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / CYL#1 (to
CYL#8).
NG Replace injector.
OK
11 Check resistance of air±fuel ratio (A/F) sensor heater.
PREPARATION:
Disconnect the air±fuel ratio (A/F) sensor connector.
CHECK:
Measure resistance between the terminals of the A/F sensor
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)1.8 to 3.4 W at 20C (68F)
HT (1) ± AF± (4)10 kW or higher
NG Replace air±fuel ratio (A/F) sensor.
OK

A19288
A/F Relay
A23659
Wire Harness Side:
HT
A38
Sensor 1A/F Sensor Connector
AF+
Front ViewAF±
+B A39
B17415
E7ECM Connector
HA1A
A1A+
A1A±
A2A+
A2A±HA2A
± DIAGNOSTICSENGINE
DI±175
369 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check A/F relay.
PREPARATION:
Remove the A/F relay from the engine room J/B.
CHECK:
Inspect the A/F relay.
OK:
Standard:
Terminal No.ConditionSpecified Condition
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace A/F relay.
OK
13 Check for open and short in harness and connector between ECM and A/F sen-
sor.
PREPARATION:
(a) Disconnect the A38 or A39 A/F sensor connector.
(b) Turn the ignition switch to ON.
CHECK:
(a) Measure the voltage between the +B terminal of the A/F
sensor connector and body ground.
OK:
Standard:
Tester ConnectionsSpecified Conditions
+B (2) ± Body ground9 to 14 V
PREPARATION:
(a) Turn the ignition switch to OFF.
(b) Disconnect the E7 ECM connector.
CHECK:
(a) Check the resistance.
OK:
Standard (Check for open):
Tester ConnectionsSpecified Conditions
HT (A38±1) ± HA1A (E7±2)
HT (A39±1) ± HA2A (E7±1)Below 1 W
AF+ (A38±3) ± A1A+ (E7±22)
AF+ (A39±3) ± A2A+ (E7±23)Below 1 W
AF± (A38±4) ± A1A± (E7±30)
AF± (A39±4) ± A2A± (E7±31)Below 1 W

A23512
Reference (Bank 1 Sensor 1 System Drawing):
A/F Sensor A/F Relay
Heater
Sensor
A1A+ HA1A
Duty
Control ECM
From
Battery
A/F Heater
Fuse
A1A±
To EFI Relay
DI±176
± DIAGNOSTICSENGINE
370 Author: Date:
2005 SEQUOIA (RM1146U)
Standard (Check for short):
Tester ConnectionsSpecified Conditions
HT (A38±1) or HA1A (E7±2) ± Body ground
HT (A39±1) or HA2A (E7±1) ± Body ground10 kW or higher
AF+ (A38±3) or A1A+ (E7±22) ± Body ground
AF+ (A39±3) or A2A+ (E7±23) ± Body ground10 kW or higher
AF± (A38±4) or A1A± (E7±30) ± Body ground
AF± (A39±4) or A2A± (E7±31) ± Body ground10 kW or higher
NG Replace or replace harness or connector.
OK
14 Replace air fuel ratio sensor.
NEXT

B17397
Vehicle Speed
Between
38 mph and 75 mph
(60 km/h and 120 km/h)
Idling
Ignition Switch OFF
3 to 5 minutes
Time 2 minutes
(a), (b), (c)(e)
(d)
± DIAGNOSTICSENGINE
DI±177
371 Author: Date:
2005 SEQUOIA (RM1146U)
15 Perform confirmation driving pattern.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Clear DTCs (see page DI±43).
(d) Switch the ECM from normal mode to check mode using the tester (see page DI±44).
(e) Start the engine and warm it up with all the accessories switched OFF.
(f) Drive the vehicle at between 38 mph and 75 mph (60 km/h and 120 km/h) and at an engine speed of
between 1,400 rpm and 3,200 rpm for 3 to 5 minutes.
HINT:
If the system is still malfunctioning, the MIL will be illuminated during step (e).
NOTICE:
If the conditions in this test are not strictly followed, no malfunction will be detected.
NEXT
16 Check whether DTC output recurs (DTC P0171, P0172, P0174 or P0175)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0171, P0172, P0174 or P0175A
No outputB
B Go to step 5.
A

B17411
E6E1
FPR
A21024
DI±182
± DIAGNOSTICSENGINE
376 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check voltage between terminal FPR and E1 of ECM.
CHECK:
Measure the voltage between terminals of E6 and E6 ECM con-
nectors.
OK:
Tester ConnectionConditionSpecified Condition
FPR (E6±30) ± E1 (E6±1)STA signal ON9 to 14 V
FPR (E6±30) ± E1 (E6±1)STA signal OFF0 to 3 V
OK Replace ECM (See page SF±80).
NG
2 Check fuel pump relay.
PREPARATION:
Remove the fuel pump relay from the engine room R/B.
CHECK:
Inspect the fuel pump relay.
OK:
Terminal No.ConditionSpecified Condition
3 ± 4Apply B+ between
terminals 1 and 210 KW or higher
3 ± 4AlwaysBelow 1 W
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace fuel pump relay.
OK

A21377
Engine Room J/B:
Fuel Pump
Relay
B17414
E6ECM Connector
FPR
± DIAGNOSTICSENGINE
DI±183
377 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check for open and short in harness and connector between fuel pump relay
and ECM.
PREPARATION:
(a) Remove the fuel pump relay from the engine room J/B.
(b) Disconnect the E6 ECM connector.
CHECK:
Measure the resistance between wire harness side connectors.
OK:
Standard:
Tester ConnectionSpecified Condition
Engine Room J/B (Fuel pump relay ter-
minal 1) ± FPR (E6±30)Below 1 W
Engine Room J/B (Fuel pump relay ter-
minal 1) or FPR (E6±30) ±
Body ground
10 kW or higher
NG Repair or replace harness or connector.
OK
Replace ECM (See page SF±80).

A20646
20 V
/Division Injector Signal Waveform
20 V
/Division
GND
100 msec./Division (Idling)(Magnification)
GND
1 msec./Division (Idling)
Injection duration
± DIAGNOSTICSENGINE
DI±185
379 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0300Misfiring of random cylinders is detected

Open or short in engine wire

Connector connection

Vacuum hose connection
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of each cylinder is detected

Vacuum hose connection

Ignition system

Injector

Fuel pressure

Mass air flow meter

Engine coolant temperature sensor

Compression pressure

Valve clearance

Valve timing

PCV piping

ECM
HINT:
When several codes for a misfiring cylinder are recorded repeatedly but no random misfire code is recorded,
it indicates that the misfires have been detected and recorded at different times.
Reference: Inspection using the oscilloscope.
With the engine idling, check the waveform between terminals #1 to #8 and E01 of the ECM connectors.
HINT:
The correct waveform is as shown in the illustration.