engine TOYOTA SEQUOIA 2001 Service Repair Manual

I18654
0.4 °
3 m (9.84 ft) H 20.9 mm
(0.823 in.)
7
V RH Line
90 °
V LH Line4V LH LineV Line V RH Line 65
6
V LH LineV Line
V RH Line 6
5
6
H4
O: step No.H4
20.9 mm
(0.823 in.) 1,348 mm (53.1 in.) Low Beam:
High Beam:29.7 mm
(1.17 in.)
20.9 mm
(0.823 in.)
1,348 mm (53.1 in.)
1,348 mm
(53.1 in.) High Beam
Low BeamH RH and
H LH
7
BE±32
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
3436 Author: Date:
2005 SEQUOIA (RM1146U)
2. ADJUST HEADLIGHT AIM ONLY
(a) Place the vehicle in the following conditions.

The area around the headlight is not deformed.

The vehicle is parked on a level surface.

Tire inflation pressure is the specified value.

A driver is in the driver's seat and the vehicle is in a state ready for driving (with a tank full).

The vehicle has been bounced several times.
(b) Check the headlight aiming.
(1) Prepare a thick white paper.
(2) Stand the paper perpendicular to the ground at the position 3 m (9.84 ft) away from the headlights
bulb center.
(3) Ensure that the center line of the vehicle and the paper face forms a 90±degree angle as shown
in the illustration.
(4) Draw a horizontal line (H line) on the paper, showing where the headlights should strike.
(5) Draw a vertical line (V line) at the position where the extended center line of the vehicle strikes.
(6) Draw 2 vertical lines (by connecting the low and high beam center marks) to where the both head-
lights should strike (V RH and V LH lines).
(7) Draw a horizontal line (by connecting the both low beam center marks) at the position where the
headlights should strike (H RH and H LH lines).
HINT:
The H RH and H LH line is 0.4° below the horizontal line (H line) of the light axis.
(8) Start the engine.
(9) Turn the headlights ON.
(10) Check that the headlights properly strike the position shown in the illustration.
(11) If not, adjust the lights in the vertical or horizontal direction.
HINT:
As shown in the illustration, adjust each aim of the RH and LH lights.
(c) When adjusting it in the vertical direction:
Using adjusting bolt, adjust the headlight aim to within the specified range.

BE033±09
I28404
Turn Signal LightHazard Warning Switch Combination Switch

Turn Signal Switch
Ignition Switch Instrument Panel J/B

FLASHER Relay
Turn Signal Light
Turn Signal Light
Engine Room J/B

TURN HAZ Fuse
± BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
BE±35
3439 Author: Date:
2005 SEQUOIA (RM1146U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION

BE175±06
I28405
Door Courtesy Light SwitchBack Door Courtesy Light Switch
Engine Room J/B

DOME Fuse
Instrument Panel J/B
Door Courtesy Light Switch
BE±38
± BODY ELECTRICALINTERIOR LIGHT SYSTEM
3442 Author: Date:
2005 SEQUOIA (RM1146U)
INTERIOR LIGHT SYSTEM
LOCATION

BE17A±06
I28425
Brake Master Cylinder

Brake Fluid Level Warning Switch
Engine Room R/B

ECU±B Fuse
Light Control Rheostat
Combination Meter Assembly
Instrument Panel J/B

IGN 2 Fuse

GAUGE Fuse
Parking Brake SwitchIgnition Switch
Passenger Seat Belt Warning
Skid Control ECU
± BODY ELECTRICALCOMBINATION METER
BE±53
3457 Author: Date:
2005 SEQUOIA (RM1146U)
COMBINATION METER
LOCATION

BE2MR±01
N06031
± BODY ELECTRICALCOMBINATION METER
BE±55
3459 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT SPEEDOMETER ON±VEHICLE
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check odometer operation.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
USA (mph)CANADA (km/h)
Standard indication Allowable rangeStandard indication Allowable range
20 19 ± 2220 17.5 ± 21.5
40 39 ± 42.540 38 ± 42
60 59.5 ± 63.560 58 ± 63
80 79.5 ± 8480 78 ± 84
100 100 ± 105100 98.5 ± 104.5
±120 119 ± 125
±140 139 ± 145
±160 159 ± 167
If error is excessive, replace the speedometer.
2. INSPECT TACHOMETER
(a) Connect a tune±up test tachometer, and start the engine.
NOTICE:

Reversing the connection of the tachometer will dam-
age the transistors and diodes inside.

When removing or installing the tachometer, be care-
ful not to drop or subject it to heavy shocks.
(b) Compare the tester and tachometer indications.
DC 13.5 V 20°C at (68°F)
Standard indicationAllowable range
700630 ± 770
1,000900 ± 1,100
2,0001,850 ± 2,150
3,0002,800 ± 3,200
4,0003,800 ± 4,200
5,0004,800 ± 5,200
6,0005,750 ± 6,250
If error is excessive, replace the tachometer.
3. INSPECT FUEL RECEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON and check that the receiver
gauge needle indicates EMPTY.

I21530
Ignition
Switch
Battery(Wire Harness Side)(3.4W) Fuel Gauge
Z05730
Warning Light
Ignition
Switch
Battery
1
23
45
Wire
Harness Side:
I28772
I01278
BE±56
± BODY ELECTRICALCOMBINATION METER
3460 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Connect terminals 2 and 3 on the wire harness side con-
nector through a 3.4 watts test bulb.
(d) Turn the ignition switch ON, check that the bulb comes on
and the receiver gauge needle moves towards the full
side.
HINT:
Because of silicon oil in the gauge, it will take a short time for
the needle to stabilize.
If operation is not as specified, inspect the receiver gauge resis-
tance.
4. INSPECT FUEL LEVEL WARNING LIGHT OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 2 and 3 on the wire harness side con-
nector.
(c) Turn the ignition switch ON and check that the warning
light comes on.
If the warning light does not come on, test the bulb or inspect
the wire harness.
5. INSPECT ENGINE COOLANT TEMPERATURE SEND-
ER GAUGE RESISTANCE
(a) Disconnect the engine coolant temperature sender
gauge.
(b) Measure the resistance between terminals 1 and 2 of the
connector according to the value(s) in the table below.
Temperature °C (°F)Resistance (W)
±20 (±4)13,840 to 16,330
20 (68)2,320 to 2,590
80 (176)310 to 326
110 (230)139.9 to 143.5
If resistance value is not as specified, replace the engine cool-
ant sender gauge.
6. INSPECT OIL PRESSURE SENDER OPERATION
(a) Disconnect the connector from the oil pressure sender.
(b) Check that no continuity exists between terminal and
ground with the engine stopped.
(c) Check that continuity exists between terminal and ground
with the engine running.
HINT:
Oil pressure should be over 24.5 kPa (0.25 kgf/cm
2, 3.55 psi).
If operation is not as specified, replace the oil pressure sender.

I01279
Warning Light
Ignition
Switch
Battery
I19428
21OFF
ON
N01212
BE1217
Warning Light
Ignition
Switch
Battery
± BODY ELECTRICALCOMBINATION METER
BE±57
3461 Author: Date:
2005 SEQUOIA (RM1146U)
7. INSPECT BRAKE WARNING LIGHT OPERATION
(a) Disconnect the connector from the brake fluid warning
switch.
(b) Release the parking brake pedal.
(c) Connect the terminals on the harness side of the level
warning switch connector.
(d) Start the engine and check that the warning light comes
on.
If the warning light does not come on, test the bulb or wire har-
ness.
8. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
CONTINUITY
(a) Remove the reservoir tank cap and strainer.
(b) Disconnect the connector.
(c) Check that no continuity exists between the terminals with
the switch OFF (float up).
(d) Use siphon, etc. to drain fluid out of the reservoir tank.
(e) Check that continuity exists between the terminals with
the switch ON (float down).
(f) Pour the fluid back in the reservoir tank.
If continuity is not as specified, replace the switch.
9. INSPECT PARKING BRAKE SWITCH CONTINUITY
(a) Check that continuity exists between the terminal and
switch body with the switch ON (switch pin released).
(b) Check that no continuity exists between the terminal and
switch body with the switch OFF (switch pin pushed in).
If operation is not as specified, replace the switch or inspect
ground point.
10. INSPECT WASHER LEVEL WARNING LIGHT OPERA-
TION
(a) Disconnect the connectors from the combination meter.
(b) Connect the negative (±) lead from the battery to terminal
16.
(c) Turn the ignition switch ON and check that the warning
light comes on.
If the warning light does not come on, test the bulb.

BE0TC±09
I28412
Mirror Assembly

Mirror Heater
Rear Window Defogger
Instrument Panel J/B

MIRROR HEATER Relay
Ignition Switch Rear Defogger SwitchEngine Room J/B

DEFOG Relay

MIR HTR Fuse
BE±64
± BODY ELECTRICALDEFOGGER SYSTEM
3468 Author: Date:
2005 SEQUOIA (RM1146U)
DEFOGGER SYSTEM
LOCATION

Disarmed state
Perform any of the following and the system will go on to ºArming preparationº:

With all the doors, the engine hood and the back door closed, lock all doors with the key.

With all the doors, the engine hood and the back door closed, lock all doors by the
wireless remote control.

With all the doors, engine hood and back door locked, open and close any of the doors, the
engine hood or the back door, then close and lock all doors, the engine hood and the back door.
Arming preparation
Perform the following and the system will
go on to ºArmed stateº:

Let 30 seconds elapse with all the doors,
engine hood and the back door closed and
locked.
Perform any of the following and the system
will return to ºDisarmed stateº:

Open any of the doors, the engine hood or
the back door .

Unlock any of the doors or the back door.

Put the key in the key cylinder.

Reconnect the battery.
Armed state
Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors or the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
Perform any of the following and the system
will go on to ºAlarm soundingº:

Open any of the doors or the back door.

Unlock any of the doors or the back door in
any way other than with a key or by the wireless
remote control.

Open the engine hood.

Reconnect the battery.

When input from the optional glass break sensor
is detected (Dealer option).(Key not inserted in key cylinder.)
Alarm sounding
The vehicle's horn and security horn will sound,
and the hazard, interior, tail and head lights come
on for 60 seconds.
After the alarm has stopped, the system will
return to ºArmed stateº. Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors and the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±83
3487 Author: Date:
2005 SEQUOIA (RM1146U)
2. ACTIVE ARMING MODE

BE0CE±10
I28416
Theft Deterrent Horn
Engine Hood Courtesy Switch Engine Room J/B
Door Lock Assembly

Door Lock Motor

Door Unlock Detection Switch
Ignition Switch

Key Unlock Warning Switch
Instrument Panel J/B
Door Courtesy Light Switch
Horn
Back Door Lock Motor
Door Key Lock
and Unlock
Switch
Door Key Lock and
Unlock Switch Headlight
Doom Light
Taillight
Body ECU
(Located behind the Instrument Panel)
Engine Room R/B No. 2
Glass Breakage Sensor ECU
Glass Breakage
Sensor Microphone
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±91
3495 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION