speed sensor TOYOTA SEQUOIA 2001 Service Repair Manual

I11929
CRUISE Main
Indicator Light
BE4034
Indicator Light
1.5 secs.0.5 secs.
ON
OFF DI±1544
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1738 Author: Date:
2005 SEQUOIA (RM1146U)
3. CHECK THE INDICATOR
(a) Turn the ignition switch to the ON position.
(b) Check that the CRUISE main indicator light comes on
when the cruise control main switch ON±OFF button is
pushed on, and that the indicator light goes off when the
ON±OFF button is pushed off.
HINT:
If there is a problem with the indicator, inspect the cruise main
indicator light circuit (see page DI±1557).
HINT:
If a malfunction occurs in the vehicle speed sensors, stop lamp
switch assy, or other related parts during cruise control driving,
the ECM will actuate AUTO CANCEL of the cruise control. The
CRUISE main indicator light will then start to blink, informing the
driver of the malfunction. At the same time, data concerning the
malfunction is stored as a diagnostic trouble code (DTC).

DIDF2±01
A08841DLC3
Hand±held Tester
DI±1548
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1742 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
According to the DATA LIST displayed by the the hand±held
tester, you can read the values of the switches, the sensors and
so on without parts removal. Reading the DATA LIST as a first
step in troubleshooting is one of the methods to shorten labor
time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on the tester, read the ºDATA
LISTº.
CCS (ECM):
ItemMeasurement Item
/Display (Range)Normal ConditionDiagnostic Note
VEHICLE SPDVehicle speed/min.: 0 km/h (0
mph), max.: 255 km/h (158 mph)Actual vehicle speed±
MEMORY SPD
Cruise control memorized speed
/min.: 36 km/h (22.5 mph), max.:
200 km/h (125 mph)
Actual stored vehicle speed±
THROTTLERequired throttle opening angle
/min.: 0
, max.: 125
Actual required throttle opening
angle±
CRUISE CONTROLCruise control system active
condition/ON or OFFON: Cruise control activated
OFF: Cruise control inactivated±
MAIN SW (MAIN)Main SW signal (Main CPU)
/ON or OFFON: Main SW ON (Pushed on)
OFF: Main SW OFF (Pushed off)±
MAIN SW (SUB)Main SW signal (Sub CPU)
/ON or OFFON: Main SW ON (Pushed on)
OFF: Main SW OFF (Pushed off)±
CCS INDICATORCruise indicator signal (Main CPU)
/ON or OFFON: ºCRUISE main indicatorº ON
OFF: ºCRUISE main indicatorº
OFF
±
CCS INDICATOR SCruise indicator signal (Sub CPU)
/ON or OFFON: ºCRUISE main indicatorº ON
OFF: ºCRUISE main indicatorº
OFF
±
CANCEL SWCANCEL SW signal/ON or OFFON: CANCEL SW ON
OFF: CANCEL SW OFF±
SET/COAST SW±/SET SW signal/
ON or OFFON: ±/SET SW ON
OFF: ±SET OFF±
RES/ACC SW+/RES SW signal/ON or OFFON: +/RES SW ON
OFF: +/RES SW OFF±
STP LIGHT SW2 MStop light SW signal (Main CPU)
/ON or OFFON: Brake pedal depressed
OFF: Brake pedal released±
STP LIGHT SW2 SStop light SW signal (Sub CPU)
/ON or OFFON: Brake pedal depressed
OFF: Brake pedal released±
STP LIGHT SW1 SStop light SW signal (Sub CPU)
/ON or OFFON: Brake pedal depressed
OFF: Brake pedal released±
SHIFT D POSPNP SW signal (D position)
/ON or OFFON: Shift position D
OFF: Any shift position except D±

DI26U±39
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1549
1743 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
If a trouble code is displayed during the DTC check, check the circuit listed for that code. For details of each
code, refer to the ºSee pageº under the respective ºDTC No.º in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble Area
P0500/21
(DI±1551)Vehicle Speed Sensor Circuit Malfunction

Vehicle speed sensor

Vehicle speed sensor signal circuit

ECM
P0503/23
(DI±1551)Vehicle Speed Sensor Circuit Malfunction

Vehicle speed sensor

Vehicle speed sensor signal circuit

ECM
P0571/52
(DI±1552)Stop Light Switch Circuit Malfunction

Stop light switch assy

Stop light switch assy circuit

ECM
P0607/54
(DI±1556)Input Signal Circuit Malfunction
ECM

DI3CI±19
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1551
1745 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC P0500/21 Vehicle speed sensor circuit malfunction
DTC P0503/23 Vehicle speed sensor circuit malfunction
CIRCUIT DESCRIPTION
See page DI±278.
DTC No.DTC Detection ConditionTrouble Area
P0500/21
This trouble code is output when the vehicle speed signal from
the vehicle speed sensor is cut for 0.14 sec. or more while the
cruise control is in operation.
Vehicle speed sensor

Vehicle speed sensor signal circuit

ECM
P0503/23
Momentary interruption and noise are detected when a rapid
change of vehicle speed occurs while the cruise control is in
operation.
Vehicle speed sensor

Vehicle speed sensor signal circuit

ECM
WIRING DIAGRAM
See page DI±278.
INSPECTION PROCEDURE
See page DI±278.

DID8P±01
I28566
Seat Position
Control ECU
A/C ECU (Integration
Control Panel) BEANBody ECU
Back Door ECU
ECM
Light Control
Rheostat
Vehicle Speed
Sensor
Oil Pressure
Sender Gauge
Fuel Sender Gauge
Seat Inner
Belt Switch
Park/neutral
Position Switch
Turn Signal
Flasher Relay
Washer Level SensorKey Unlock
Warning Switch
Door Courtesy
Lamp Switch
Parking Brake Switch
Transponder
Key ECU
4WD Control ECU
Airbag Sensor
Center ECU Combination
Meter
Skid Control ECU
Suspension
Control ECU
Translate ECU
Overhead Module
(Garage Door
Opener)BEAN
BEAN
BEAN
BEAN
BEAN BEAN
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1605
1799 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DID8Q±01
DI±1608
± DIAGNOSTICSCOMBINATION METER SYSTEM
1802 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. METER GAUGE AND WARNING/INDICATOR
GAUGE:
ItemDetail
SpeedometerVehicle speed sensor (Direct line).
TachometerECM transmits engine speed to the meter to display.
ODO/TRIP MeterCombination meter assy.
FuelDisplays a fuel level according to a signal from the fuel sender gauge (Direct line).
Water TemperatureDisplays engine coolant temperature according to a signal from the ECM (BEAN).
Oil PressureReceives a signal from the oil pressure sender (Direct line).
Volt MeterDisplays vehicle voltage according to a voltage from the IG terminal (Direct line).
WARNING/INDICATOR:
HINT:
Combination meter bulb check is performed for 3 seconds after the ignition switch is turned ON.
ItemDetailList of indicators available for
bulb check
O/D OFFReceives a signal from the ECM (Direct line)±
TURNTurns signal switch ON (Direct line)±
BEAMReceives a signal from the body ECU (*1), Displays a signal received from the
dimmer switch (*2) (Direct line)±
SECURITYReceives a set signal from the transponder key ECU and body ECU (Direct line)±
CHARGEReceives a malfunction signal from the alternator (Direct line)
AIR BAGReceives a malfunction signal from the airbag sensor center (Direct line)
D SEAT BELTReceives the driver seat belt signal (Unfastened) from the seat belt inner front LH
(Direct line)±
DOOROpen door indicator comes on when a signal is received from the ECU (BEAN)
from each door±
A/T OIL TEMP.Warning is displayed when the oil temperature is high (Direct line)
BRAKEComes on when the parking brake switch is on or the brake fluid level warning
switch is on (Direct line)
MIL (CHECK ENGINE)Receives a malfunction signal from the ECM (Direct line)
FUEL WARNINGReceives the fuel empty signal from the fuel sender gauge (Direct line)±
ABSReceives a malfunction signal from the skid control ECU (Direct line)
WASHERWarning is displayed when the washer level is low (Direct line)±
CRUISEReceives a CRUISE on signal or malfunction signal from the ECM (Direct line)±
VSC TRACReceives a malfunction signal from the skid control ECU (Direct line)
VSC (TRAC) OFFReceives a malfunction signal from the translate ECU (Direct line)
SLIPReceives a malfunction signal from the translate ECU (Direct line)
4HIReceives a 4HI signal from the 4WD control ECU (Direct line)±
CTR DIF LOCKReceives a DIF LOCK signal from the 4WD control ECU (Direct line)±
A/T PReceives a P signal from the park/neutral position switch (Direct line)±
A/T NReceives an N signal from the park/neutral position switch (Direct line)±
A/T DReceives a D signal from the park/neutral position switch (Direct line)±
A/T 3Receives a 3 signal from the park/neutral position switch (Direct line)±
A/T 2Receives a 2 signal from the park/neutral position switch (Direct line)±
A/T LReceives an L signal from the park/neutral position switch (Direct line)±

DID8U±01
DI±1614
± DIAGNOSTICSCOMBINATION METER SYSTEM
1808 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
Inspect the related ºFuseº and ºRelayº before confirming the suspected area as shown in the table below.
MALFUNCTION SYSTEM:
SymptomSuspected AreaSee page
Entire combination meter does not operate.Refer to troubleshooting proceduresDI±1628
Operating light control rheostat does not change light brightness.Refer to troubleshooting proceduresDI±1645
Seat belt warning does not operate.Refer to troubleshooting proceduresDI±1650
Key reminder warning buzzer does not sound.
1. Multiplex communication system
2. Key unlock warning switch circuit
3. Door courtesy lamp switch circuit
4. Combination meter assyDI±1892
DI±1715
DI±1728
IN±35
METER GAUGES:
SymptomSuspected AreaSee page
Malfunction in speedometerRefer to troubleshooting proceduresDI±1632
Malfunction in tachometerRefer to troubleshooting proceduresDI±1636
Malfunction in fuel receiver gaugeRefer to troubleshooting proceduresDI±1640
Malfunction in engine coolant temperature receiver gaugeRefer to troubleshooting proceduresDI±1644
Malfunction in oil pressure receiver gaugeRefer to troubleshooting proceduresDI±1654
Malfunction in volt meterRefer to troubleshooting proceduresDI±1658
WARNING LIGHTS:
SymptomSuspected AreaSee page
Check engine warning light (MIL) does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Discharge warning light does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Brake warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
ABS warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
SRS warning light does not come on.
1. Airbag sensor assy
2. Wire harness or connector
3. Combination meter assyDI±1126
±
IN±35
Open door warning light does not come on.
1. Door courtesy light switch circuit
2. Wire harness or connector
3. Combination meter assy
4. Body ECUDI±1728
±
IN±35
IN±35
Fuel level warning light does not come on.
1. Refer to troubleshooting
2. Wire harness or connector
3. Combination meter assyDI±1640
±
IN±35
Low oil pressure warning light does not come on.
1. Low oil pressure warning switch
2. Wire harness or connector
3. Combination meter assyBE±55
±
IN±35

Wire harness side
1
2
3
4
5
6
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
401
2
3
4
5
8 6
10
11
12
13
14
15
16
17
18
19
21
23
24
Terminal No.
Translate ECU
ECM
STA Fuse
Front Seat Inner Belt LH (Buckle Switch)
Overhead Module (Garage Door Opener)
Overhead Module (Garage Door Opener)
Washer Level Sensor
ECM
ECM (*1)
Transponder Key Computer
Body ECU
ECM
ECM
Tire Pressure Monitor ECU
Injector No. 1
Light Control Rheostat
ECM
Speed Sensor
4P OUT (Other Parts)
Fuel Sender Gauge
Oil Pressure Sender Gauge
IGN Fuse
Airbag Sensor Assembly
Memory Seat ECU and SW (*2)
Back Door ECU
Integration Control and Panel
Turn Signal Flasher Relay
Park/Neutral Position Switch
Airbag Sensor AssemblyTranslate ECU
Translate ECU
Skid Control ECU
4WD Control ECU
Alternator
Speed Sensor
Fuel Sender Gauge
Ground
Suspension Control ECU
Body ECU (*4)
Body ECU (*3)
Turn Signal Flasher Relay
Skid Control ECU
ECU±B Fuse
IGN1 Fuse Connectors:
Terminal No.
Wire harness side
C5
C64WD Control ECU
4WD Control ECU
Suspension Control ECU
Suspension Control ECU
Suspension Control ECU
*1: 4WD
*2: w/ Driving Position Memory
*3: w/ Daytime Running Light
*4: w/o Daytime Running LightPark/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch DI±1624
± DIAGNOSTICSCOMBINATION METER SYSTEM
1818 Author: Date:
2005 SEQUOIA (RM1146U)

DID8X±01
DI±1626
± DIAGNOSTICSCOMBINATION METER SYSTEM
1820 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
DATA LIST
According to the DATA LIST displayed by the hand±held tester, you can read the values of the switches,
sensors, actuators and so on without part removal. Reading the DATA LIST as the first step of troubleshoot-
ing is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
SPEED METER
Vehicle Speed Meter /
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Almost the same as actual vehicle
speed (When driving)
TACHO METEREngine RPM /
Min.: 0 rpm Max.: 12,750 rpmAlmost the same as actual engine
speed (When engine is running)
FUEL GAUGEFuel Input /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the fuel receiver gauge
angle.

LIGHT RHEOSTATLight Control Rheostat /
Min.: 0 Max.: 255Light control rheostat switch is
Dark (0) " Bright (255)
OIL GAUGEOil Gauge /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the oil pressure receiver
gauge angle.

ODO/TRIP SWODO / TRIP
ODO/TRIP switch / ON/OFFON: Switch is pushed
OFF: Switch is released

I28558
C612
W±B
Battery AW
58BR
IECombination Meter
W±L I18
Ignition SW
2 1
AM1 IG1
B±Y
W Instrument Panel J/B
AM1
21 47
6 1 6
9 1C
1C
1D 1E
1L
1FR±L
R±LSub J/B No. 3
3B 3A515C524
C610 R±L
Y±RY
Y±RY
13
23 19
26
IG4
IG4
IG4
GAUGE
B V1
Vehicle Speed Sensor
(Combination Meter)
F10
Fusible Link Block
J8
J/C DI±1632
± DIAGNOSTICSCOMBINATION METER SYSTEM
1826 Author: Date:
2005 SEQUOIA (RM1146U)
Malfunction in speedometer
CIRCUIT DESCRIPTION
The speedometer detects vehicle speed based on a 4±pulse signal from the vehicle speed sensor.
WIRING DIAGRAM
DID8Z±01