warning light TOYOTA SEQUOIA 2001 Service User Guide

D14231
When fluid
temperature
is low: offWhen fluid
temperature
is correct: onWhen fluid
temperature
is high: blinks
D14139Overflow Plug
D14141
D14140
Refill Plug
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±533
727 Author: Date:
2005 SEQUOIA (RM1146U)
(7) Lift up the vehicle immediately after the meter indi-
cator light (ATF temperature warning light) comes
on.
NOTICE:

Add fluid only when the meter indicator light is on.

Perform this procedure while the engine is idling.
(8) Remove the overflow plug. If ATF overflows, pro-
ceed to [*5]. If ATF does not overflow, proceed to
[*6].
HINT:
ºOverflowº indicates the condition under which ATF drains out
from the overflow tube.
(e) When fluid overflows: [*5]
(1) Install the overflow plug with a new gasket when the
draining ATF has become a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(2) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(3) Lower down the vehicle.
(4) Turn the ignition switch off.
(5) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.
(f) When fluid does not overflow: [*6]
(1) Remove the refill plug.

DI±554
± DIAGNOSTICSAUTOMATIC TRANSMISSION
748 Author: Date:
2005 SEQUOIA (RM1146U) Shift point too high or too low
1. Shift solenoid valve (SLT) circuit *1
2. Speed sensor NT circuit *1
3. Speed sensor SP2 circuit *1
4. Throttle position sensor circuit *1
5. ATF temperature sensor circuit *1
6. ECM
DI±662
DI±591
DI±596
DI±58
DI±582
IN±35
Up±shift to 5th from 4th while shift lever is in 4 position1. O/D main switch circuit
2. ECMDI±688
IN±35
Up±shift to 5th from 4th while engine is cold1. Engine coolant temp. sensor circuit *1
2. ECM
DI±58
IN±35
Up±shift to 4th from 3rd while shift lever is in 3 position1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35
Up±shift to 3rd from 2nd while shift lever is in 2 position1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35
Up±shift to 2nd from 1st while shift lever is in L position1. Shift position L switch circuit
2. ECMDI±691
IN±35
Harsh engagement (N " D)
1. Speed sensor NT circuit *1
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI±591
DI±603
DI±662
IN±35
Harsh engagement (Lock±up)
1. Speed sensor NT circuit *1
2. Speed sensor SP2 circuit *1
3. Shift solenoid valve (SLU) circuit *1
4. ECM
DI±591
DI±596
DI±680
IN±35
Harsh engagement (Any driving position)ECMIN±35
Poor acceleration
1. ATF temperature sensor No.2 circuit *1
2. Engine coolant temp. sensor circuit *1
3. Shift solenoid valve (SLT) circuit *1
4. ECM
DI±666
DI±58
DI±662
IN±35
No engine brakingECMIN±35
No kick±downECMIN±35
Engine stalls when starting off or stopping1. Shift solenoid valve (SLU) circuit *1
2. ECM
DI±680
IN±35
AT Oil Temp. warning light remains on1. ATF temperature sensor No.2 circuit*1DI±666
Lock±up at 3rd gear
1. AT F temperature sensor No.2 circuit 1
2. Engine coolant temp. sensor circuit *1DI±666
DI±58
Shift point too high
2. Engine coolant tem . sensor circuit
3. ECMDI 58
IN±35
Malfunction in shifting1. Park/neutral position switch circuit *1
2. ECM
DI±576
IN±35

DI±666
± DIAGNOSTICSAUTOMATIC TRANSMISSION
860 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2740 Transmission Fluid Temperature Sensor ºBº
Circuit
DTC P2742 Transmission Fluid Temperature Sensor ºBº
Circuit Low Input
DTC P2743 Transmission Fluid Temperature Sensor ºBº
Circuit High Input
CIRCUIT DESCRIPTION
ATF (Automatic Transmission Fluid) temperature sensor No.2 is on the transmission and just in front of the
oil cooler inlet pipeline.
If ECM detects the abnormally high temperature of ATF by this sensor, it draws driver's attention by illuminat-
ing the warning lamp.
HINT:

The temperature of ATF easily rises when towing, climbing hills and in traffic, etc.

If the ATF temperature sensor No.2 becomes short±circuited, the signal that indicates the ATF temper-
ature is 150C (302F) or higher is input in ECM.
Vehicle conditions when the sensor is normal and when the sensor is short±circuited are indicated
in the table below.
ATF temperature Sensor No.2
StateDetection ConditionSymptomRecovery Condition

AT fluid temp. more than 150C
(302F).
AT Oil Temp. warning light re-
mains on
AT fluid temp. less than 135C
(275F). *2

AT fluid temp. more than 130C
(266F).
Shift point too high.
AT fluid temp. less than 110C
(230F).
Sensor is normalWhen the conditions (a) and (b)
are satisfied.
(a) AT fluid temp. more than 130C
(266F).
(b) Engine coolant temp. more
than 95C (203F).

Lock±up at 3rd gear. *1
AT fluid temp. less than 110C
(230F) *2 and engine coolant
temp. less than 95C (203F).
Sensor is short±circuited

Any conditions.

AT Oil Temp. warning light re-
mains on

Shift point too high.

Symptoms still occur
Sensor is short circuited

Engine coolant temp. more than
95C (203F).
Lock±up at 3rd gear. *1
Symptoms still occur
HINT:
*1: When AT fluid temperature is normal, transmission locks up at 5th gear with the shift lever in D position
and at 4th gear with the shift lever in 4 position.
*2: When AT fluid temperature is in normal range, it decreases to less than 135C (275F) within 5 minutes
with the shift lever in P or N position in an idling state.
DIDJN±01

± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±771
965 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Inspect courtesy light switch.
CHECK:
Check that the open door warning light comes on when any door or back door is opened and goes off when
all the doors are closed.
OK:
Courtesy light operates normally.
NG Check open door warning light
(See page DI±1608).
OK

DIDK1±01
DI±814
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1008 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during DTC check but the problem still occurs, check the circuits for each prob-
lem symptom in the order given in the table below and proceed to the relevant troubleshooting page.
SymptomSuspected AreaSee page
Tire pressure warning system does not operate.
1. Tire pressure monitor valve sub±assy
2. Tire pressure monitor receiver assy
3. Power source circuit
4. Tc terminal circuit
5. Combination meter assy
6. Tire pressure monitor ECU±
±
DI±878
DI±888
BE±55
±
DTC check cannot be done.
1. Power source circuit
2. Tc terminal circuit
3. Tire pressure monitor ECUDI±878
DI±888
±
Tire pressure warning lamp malfunctions (Does not light up).
1. Power source circuit
2. Tire pressure warning lamp circuit
3. Combination meter assy
4. Tire pressure monitor ECUDI±878
DI±873
BE±55
±
Tire pressure warning lamp malfunctions (Remains ON).
1. Tire pressure check
2. Tire pressure monitor ECU connector poorly connected
3. Tire pressure warning lamp circuit
4. Combination meter assy
5. Tire pressure monitor ECUSA±3
±
DI±873
BE±55
±
Tire pressure warning lamp malfunctions (Blinking).
1. Check DTC
2. Tc terminal circuit
3. Test mode (SIGNAL CHECK)
4. Tire pressure monitor ECUDI±820
DI±888
DI±810
±
Initialization cannot be done.
1. Test mode (SIGNAL CHECK)
2. Tire pressure warning reset switch
3. Tire pressure monitor ECUDI±810
DI±875
±

DIDLV±01
F17996
Front Speed SensorABS & VSC Actuator
(w/ Skid Control ECU)Level Warning Switch
Rear Speed Sensor Rear Speed Sensor Rotor
Front Speed
Sensor Rotor
Parking Brake SwitchStop Light Switch
Center Diff. Lock Switch *1
TRAC OFF Switch *2
Steering Angle Sensor
DLC3Brake Inhibit RelayTranslate ECU
VSC BuzzerBrake Booster
(Including Active Brake Booster
Solenoid, Delta S Sensor and Boost-
er Pedal Switch)
Master Cylinder
Pressure Sensor
Front Speed Sensor Rotor
Front Speed Sensor
Yaw Rate Sensor
(Including Deceleration Sensor)
ABS Warning Light
VSC TRAC Warning light
VSC OFF Indicator Light *
1
TRAC OFF Indicator Light *2
BRAKE Warning Light
SLIP Indicator Light
*1: Only for 4WD
*2: Only for 2WDCenter Diff. Lock
Position Switch
DI±892
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1086 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDLX±01
DI±894
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1088 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. SYSTEM DESCRIPTION
HINT:

The yaw rate sensor and deceleration sensor are combined and in a single unit. This unit communi-
cates with the skid control ECU through the CAN communication system.

No changes have been made to the communication method between the VSC system and ECM. How-
ever, the communication method between the Translate ECU and ECM has been changed from serial
to CAN communication.
(a) ABS
(Anti±lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking
on a slippery surface.
(b) EBD
(Electronic Brake force Distribution)
The EBD control utilizes ABS, realizing proper brake force distribution between front and rear wheels
in accordance with driving conditions.
In addition, during braking while cornering, it also controls the brake forces of the right and left wheels,
helping to maintain vehicle behavior.
(c) BA (Brake Assist)
The primary purpose of the brake assist system is to provide an auxiliary brake force to assist the driver
who cannot generate a large enough brake force during emergency braking, thus helping to maximize
the vehicle's braking performance.
(d) TRAC
(Traction Control)
The TRAC system helps prevent the drive wheels from slipping if the driver presses down on the accel-
erator pedal excessively when starting off or accelerating on a slippery surface.
(e) VSC
(Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front wheel skid
or strong rear wheel skid during cornering.
2. ABS with EBD & BA & TRAC & VSC OPERATION
(a) The skid control ECU calculates vehicle stability tendency based on signals from the speed sensor,
yaw rate (deceleration) sensor and steering angle sensor. In addition, it evaluates the results of the
calculations to determine whether any control actions (control of the engine output torque by electronic
throttle control and of the wheel brake pressure by the brake actuator) should be implemented.
(b) The SLIP indicator blinks and the VSC buzzer sounds to inform the driver that the VSC system is oper-
ating. The SLIP indicator also blinks when TRAC is operating, and the operation being performed is
displayed.
3. FAIL SAFE FUNCTION
(a) When a failure occurs in the ABS & BA & TRAC & VSC systems, the ABS and VSC warning lights come
on and ABS & BA & TRAC & VSC operations are prohibited. In addition to this, when there is a failure
that disables EBD operation, the brake warning light also comes on and EBD operation is prohibited.
(b) If some control is prohibited due to a malfunction during its operation, that control will be cut off gradual-
ly not to change the stability of the vehicle suddenly.

DI93A±03
Inspector 's
Name:
Customer 's Name
Date Vehicle
Brought InRegistration DateRegistration No.
Frame No.
Odometer Reading/ /
/ /
Date Problem First Occurred
Frequency Problem Occurs/ /
ContinuousIntermittent ( times a day)
Remains ONDoes not Light Up
DTC Check1st Time
2nd TimeNormal System Code
Trouble Code (Code )
Symptomskm
miles
Check ItemNormal
ABS does not operate.
ABS does not operate efficiently.
Does not Light Up
ABS & BA & TRAC & VSC Check Sheet
VSC does not operate. (Wheels sideslip when turning sharply.)
ABS Warning Light
Abnormal
Remains ON
Does not Light Up
Remains ONDoes not Light Up
Remains ONDoes not Light Up
Remains ONDoes not Light Up
TRAC OFF Indicator
Light Abnormal*1
SLIP Indicator
Light Abnormal VSC TRAC Warning
Light Abnormal
BRAKE Warning
Light Abnormal
Malfunction
Indicator Light
TRAC does not operate. (Wheels spin when starting off rapidly.)
Remains ON
Does not Light UpVSC OFF Indicator
Light Abnormal*2
BA does not operate
Normal System Code
Trouble Code (Code )
DI±896
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1090 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK
*1: Only for 2WD
*2: Only for 4WD

DIDLZ±01
F09750
DLC3Ts
CG
BR3904
0.13 sec. 0.13 sec.
ON
OFF
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±899
1093 Author: Date:
2005 SEQUOIA (RM1146U)
TEST MODE PROCEDURE
1. When not using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or the ECU, perform
zero point calibration of the master cylinder pressure, yaw
rate and deceleration sensors (See page DI±897).
HINT:
If the ignition switch is turned from the ON to the ACC or LOCK
position in test mode, test mode DTCs will be erased.
(a) Procedures for test mode:
(1) Turn the ignition switch OFF.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(4) Start the engine.
(5) Check that the ABS and VSC TRAC warning lights
blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057

F09750
CG TcDLC3
BR3893
Trouble Code (Example Code 72, 76)
ON
OFF
4 sec. 1.5 sec.
Repeat 2.5 sec.
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.7726
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±901
1095 Author: Date:
2005 SEQUOIA (RM1146U)
(f) Read the DTC.
(1) Using SST, connect terminals Tc and CG of the
DLC3.
SST 09843±18040
(2) Read the number of blinks of the warning light.
HINT:

See the list of DTC (step 3).

If all sensors are normal, a normal system code is output
(A cycle of 0.25 sec. ON and 0.25 sec. OFF is repeated).

If 2 or more malfunctions are indicated at the same time,
the codes will be displayed in ascending order.
(3) After doing the check, disconnect terminals Ts and
CG, Tc and CG of the DLC3, and turn the ignition
switch OFF.
SST 09843±18040