TOYOTA SEQUOIA 2001 Service Repair Manual

AC1LZ±05
I21428
1 2
AC±96
± AIR CONDITIONINGCONDENSER FAN
3823 Author: Date:
2005 SEQUOIA (RM1146U)
CONDENSER FAN
ON±VEHICLE INSPECTION
1. INSPECT CONDENSER FAN OPERATION
Inspect the fan operation under the following conditions, as
shown in the chart.
Test conditions:

Start engine

Blower speed control switch position ºHIº

Temperature control dial at ºCOOLº position

Set manifold gauge set

A/C switch ON
ConditionFan operation (Fan speed)
Refrigerant pressure is less than
1,520 kPa (15.5 kgf/cm2, 220 psi)OFF
Refrigerant pressure is 1,520 kPa
(15.5 kgf/cm2, 220 psi) or aboveRotate
If operation is not as specified, proceed to the next inspection.
2. INSPECT CONDENSER FAN MOTOR OPERATION
(a) Disconnect the fan connector.
(b) Connect the battery and ammeter.
(c) Check that the fan rotates smoothly, and then check the
reading on the ammeter.
Specified amperage: 9.2 to 11.0 A at 20°C (68°F)
If operation is not as specified, replace the fan motor.
If operation is as specified, check the pressure switch, cooling
fan relays and water temp. switch.

AC1M0±04
I21429
Fan
Fan Shroud
MotorCondenser Fan
Wire Harness
± AIR CONDITIONINGCONDENSER FAN
AC±97
3824 Author: Date:
2005 SEQUOIA (RM1146U)
COMPONENTS

I21430
AC1M1±05
AC±98
± AIR CONDITIONINGCONDENSER FAN
3825 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
REMOVE CONDENSER FAN
(a) Disconnect the 2 connectors.
(b) Disconnect the wire harness clamp.
(c) Remove the ambient temperature sensor.
(d) Remove the 4 bolts and condenser fan with the fan
shroud.

AC3HV±02
I21431
I21432
± AIR CONDITIONINGCONDENSER FAN
AC±99
3826 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
1. REMOVE FAN
Remove the 3 bolts and fan.
2. REMOVE FAN MOTOR FROM FAN SHROUD
Remove the 3 screws and fan motor.

AC1M3±01
AC±100
± AIR CONDITIONINGCONDENSER FAN
3827 Author: Date:
2005 SEQUOIA (RM1146U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page AC±99).

AC1M4±02
± AIR CONDITIONINGCONDENSER FAN
AC±101
3828 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page AC±98).

AC3I1±03
I21397
Center Cluster
Integration Panel
Heater
Control
Housing
A/C Amplifier
Seat Belt Indicator Circuit
BulbBulb
Bulb
Knob
Knob
Knob
Integration Panel
Knob
AC±102± AIR CONDITIONINGAIR CONDITIONER CONTROL ASSEMBLY (Center
Cluster Integration)
3829 Author: Date:
2005 SEQUOIA (RM1146U)
AIR CONDITIONER CONTROL ASSEMBLY (Center Cluster
Integration)
COMPONENTS

I213985 Clips
AC3HW±02
± AIR CONDITIONINGAIR CONDITIONER CONTROL ASSEMBLY (Center
Cluster Integration)AC±103
3830 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
REMOVE CENTER CLUSTER INTEGRATION PANEL
(a) Remove the 2 screws.
(b) Remove the integration control panel by pulling the por-
tions indicated by arrows in the illustration.
(c) Disconnect the connector.

I21399
AC3HX±03
I21400
I21401
I21402
I21417
AC±104± AIR CONDITIONINGAIR CONDITIONER CONTROL ASSEMBLY (Center
Cluster Integration)
3831 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
1. REMOVE BULBS
Remove the 3 bulbs.
2. REMOVE A/C AMPLIFIER
(a) Remove the 7 screws and heater control housing.
(b) Disconnect the 2 connectors.
(c) Remove the 3 screws and A/C amplifier.
(d) Remove the passenger seat belt indicator circuit.
3. REMOVE INTEGRATION CIRCUIT
(a) Remove the 2 knobs.
(b) Remove the 2 nuts and 2 washers.

I21416
I21403
± AIR CONDITIONINGAIR CONDITIONER CONTROL ASSEMBLY (Center
Cluster Integration)AC±105
3832 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Remove the 8 bulbs.
(d) Remove the 7 screws and integration circuit.