child seat TOYOTA SEQUOIA 2001 Service Repair Manual

H23981
Occupant
Classification Sensor
Occupant
Classification ECU
Occupant Load
A
A ± A Cross Section
Occupant
Classification Sensor
Occupant
Classification Sensor
A
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1125
1319 Author: Date:
2005 SEQUOIA (RM1146U)
3. DESCRIPTION OF OCCUPANT CLASSIFICATION SYSTEM
(a) GENERAL DESCRIPTION.
(1) In the occupant classification system, the occupant classification ECU calculates the weight of
the occupant based on a signal from the occupant classification sensor. This system recognizes
the occupant to be a child if it detects a weight of less than 36 kg (79.37 lb), and disables the
front and side airbags.
(2) This system is mainly comprised of 4 occupant classification sensors that detect the load on the
front passenger seat. The occupant classification ECU controls the system, and the passenger
airbag ON/OFF indicator indicates the ON/OFF condition of the front passenger airbag assembly
and side airbag assembly (passenger side).
(b) OCCUPANT CLASSIFICATION SENSOR.
The occupant classification sensors are installed on 4 brackets connecting the seat rail and seat frame.
Accordingly, when load is applied to the passenger seat by an occupant sitting in it, the occupant classi-
fication sensors register a distortion.

DI±1140
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1334 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Review.
(1) When the SRS airbag system is normal:
The SRS warning light comes on only during the primary check period (for approximately 6 se-
conds after the ignition switch is turned to the ON position).
(2) When the SRS airbag system has trouble:

The SRS warning light remains on even after the primary check period has elapsed.

The SRS warning light goes off after the primary check, but comes on again during the
constant check.

The SRS warning light does not come on when turning the ignition switch from the LOCK
to ON position.
HINT:
The airbag sensor assembly keeps the SRS warning light on if the airbag has been deployed.
4. FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR
The passenger airbag ON/OFF indicator function as follows:
(1) Turn the ignition switch to the ON position.
(2) The passenger airbag ON/OFF indicator (ºONº and ºOFFº) comes on for approximately 4 se-
conds, then goes off for approximately 2 seconds.
(3) Approximately 6 seconds after the ignition switch is turned to the ON position, the passenger
airbag ON/OFF indicator will be ON/OFF depending on the conditions listed below.
HINT:
If the front passenger seat condition and the indication by the passenger airbag ON/OFF indicator differ from
those shown in the table below, and the SRS warning light is off, then the DTC is not output. If this occurs,
perform troubleshooting of ºTrouble in indication of Passenger airbag ON/OFF indicatorº (see page
DI±1485).
ConditionºONº indicatorºOFFº indicator
VacantOFFOFF
Adult is seated.ONOFF
Child is seated.OFFON
Child restraint system (CRS) is set.OFFON
Occupant classification system failureOFFON

DIDGP±01
DI±1152
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1346 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
HINT:
By accessing the DATA LIST displayed by the hand±held tester, you can perform such functions as reading
the values of the switches and sensors without removing any parts. Reading the DATA LIST is the first step
of troubleshooting and is one method to shorten labor time.
1. DATA LIST FOR AIRBAG SENSOR ASSEMBLY
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Following the display on the tester screen, read the ºDATA LISTº.
ItemMeasurement tem/
Range (Display)Normal ConditionDiagnostic Note
D SEAT POSITION
Seat position (Driver side)/
FORWARD: Seat position
is forward
BKWARD: Seat position is
rearward
FAIL: A failure is detected
FORWARD/BKWARD±
PASSENGER CLASS
Passenger classification/
NG: Data is not deter-
mined
NONE: Vacant
CHILD: Child (less than 36
kg (79.37 lb)) is seated
SMALL: Adult (36 to 54 kg
(79.37 to 119.05 lb)) is
seated
REGULAR: Adult (more
than 54 kg (119.05 lb)) is
seated
FAIL: A failure is detected
NG/NONE/CHILD/SMALL/
REGULAR±
D BUCKLE SW
Buckle switch (Driver side)/
UNSET: The seat belt is
not fastened
SET: The seat belt is fas-
tened
NG: Data is not deter-
mined
UNSET/SET±
P BUCKLE SW
Buckle switch (Passenger
side)/
UNSET: The seat belt is
not fastened
SET: The seat belt is fas-
tened
NG: Data is not deter-
mined
UNSET/SET±
DISPLAY TYPE
Display type identification
information/
LR: The display is indi-
cated by LH/RH
DP: The display is indi-
cated by Driver/Passenger
LR/DPFor this vehicle, the display
is displayed by LH/RH.

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1153
1347 Author: Date:
2005 SEQUOIA (RM1146U)
2. DATA LIST FOR OCCUPANT CLASSIFICATION ECU
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Following the display on the tester screen, read the ºDATA LISTº.
ItemMeasurement Item/
Range (Display)Normal ConditionDiagnostic Note
IG SW
Ignition switch condition/
ON: Ignition switch ON
OFF: Ignition switch OFF
ON/OFF±
P BUCKLE SW
Buckle switch (Passenger
side)/
OFF: Unfasten the pas-
senger side seat belt
ON: Fasten the passenger
side seat belt
NG: Passenger side seat
belt has a trouble
OFF/ON±
PASSENGER CLASS
Passenger classification/
AF05: Adult (36 to 54 kg
(79.37 to 119.05 lb)) is
seated
AM50: Adult (more than 54
kg (119.05 lb)) is seated
CHILD: Child (less than 36
kg (79.37 lb) is seated
CRS: Child restraint sys-
tem (less than 7 kg (15.43
lb)) and passenger side
buckle switch is ON, then
7 to 36 kg (15.43 to 79.37
lb)) is set
OFF: Vacant
AF05/AM50/CHILD/CRS/
OFF±
SENS RANGE INF
Sensor range information/
OK: The value of a sensor
is within the range
NG: The value of a sensor
is over the range
OK±
FL SENS RANGE
Front left sensor range in-
formation/
OK: Sensor range is ±17
to 27 kg (±37.48 to 59.52
lb)
Min.: Less than ±17 kg
(±37.48 lb)
Max.: More than 27 kg
(59.52 lb)
OK±
FR SENS RANGE
Front right sensor range in-
formation/
OK: Sensor range is ±17
to 27 kg (±37.48 to 59.52
lb)
Min.: Less than ±17 kg
(±37.48 lb)
Max.: More than 27 kg
(59.52 lb)
OK±

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1485
1679 Author: Date:
2005 SEQUOIA (RM1146U)
Trouble in Indicator of Passenger Airbag ON/OFF Indicator
CIRCUIT DESCRIPTION
The occupant classification system detects the front passenger seat condition. It then informs a passenger
of the front passenger airbag assembly condition (activated/not activated) by the passenger airbag ON/OFF
indicator.
The table below shows the normal indication condition of the passenger airbag ON/OFF indicator and the
front passenger seat condition.
Front passenger seat conditionON IndicatorOFF Indicator
Adult is seated.ONOFF
Child is seated.OFFON
VacantOFFOFF
Occupant classification system failureOFFON
INSPECTION PROCEDURE
1 Check SRS warning light.
CHECK:
Turn the ignition switch to the ON position, and check the SRS warning light condition.
HINT:
If this trouble occurs, the SRS warning light is off. If it is on, a DTC is output. Troubleshoot for the output DTC.
OK:
The SRS warning light does not come on.
NG Check DTC (see page DI±1147).
OK
DIDHT±01

DI±1486
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1680 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check passenger airbag ON/OFF indicator condition.
PREPARATION:
Turn the ignition switch to the ON position.
CHECK:
Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.
OK:
Front passenger seat conditionON IndicatorOFF Indicator
Adult is seated.ONOFF
Child is seated.OFFON
VacantOFFOFF
Occupant classification system failureOFFON
NG Go to step 3.
OK
END

H16780
42 (430, 31)
No. 2 Rear Window
Side Garnish
Rear Trim
Rear No. 1 Seat
Outer BeltRear Seat Shoulder
Belt Cover Rear Window
Side Garnish Adjustable Anchor
Rear Door
Opening Trim
Weatherstrip
Rear Door
Scuff PlateRear No. 2 Seat
Outer Belt
Rear Seat
Shoulder
Belt Guide
Rear
Outer BeltRear No. 2 Inner BeltChild Comfort Guide
Rear Seat LockDome Light
Lens
Rear Trim Cover
Rear Floor Mat
Support Plate Rear No. 2 Seat
Outer Center Belt
Quarter Trim
Panel
Rear No. 1
Inner Belt
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
8.5 (87, 76 in.´lbf)
8.5 (87, 76 in.´lbf)
N´m (kgf´cm, ft´lbf) : Specified torque
42 (430, 31)
42 (430, 31)
42 (430, 31)
Front
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
BO±160
± BODYSEAT BELT
3713 Author: Date:
2005 SEQUOIA (RM1146U)

05_SEQUOIA_U (L/O 0408)
iii
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Important information about your Toyota
Occupant restraint systems
Toyota encourages you and your family to take the time to
read Section 1±3 of this Owner 's Manual carefully. In
terms of helping you understand how you can receive the
maximum benefit of the occupant restraint systems this
vehicle provides, Section 1±3 of this Owner 's Manual is
the most important Section for you and your family to
read.
Section 1±3 describes the function and operation concern-
ing seats, seat belts, SRS airbags and child restraint sys-
tems of this vehicle and some potential hazards you
should be aware of. These systems work together along
with the overall structure of this vehicle in order to provide
occupant restraint in the event of a crash. The effect of
each system is enhanced when it is used properly and
together with other systems. No single occupant restraint
system can, by itself, provide you or your family with the
equal level of restraint which these systems can provide
when used together. That is why it is important for you and
your family to understand the purpose and proper use of
each of these systems and how they relate to each other.
The purpose of all occupant restraint systems is to help
reduce the possibility of death or serious injury in the
event of a collision. None of these systems, either individ-
ually or together, can ensure that there is no injury in the
event of collision. However, the more you know about
these systems and how to use them properly, the greater
your chances become of surviving an accident without
death or serious injury.
Seat belts provide the primary restraint to all occupants of
the vehicle, and every occupant of the vehicle should wear
seat belts properly at all times. Children should always be
secured in child restraint systems that are appropriate for
their age and size. SRS (Supplemental Restraint System)
airbags are, as their names imply, designed to work with,
and be supplemental to, seat belts and are not substitutes
for them. SRS airbags can be very effective in reducing
the risk of head and chest injuries by preventing contact of
the head and chest with interior portions of the vehicle.

05_SEQUOIA_U (L/O 0408)
25
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
This double key turning operation to un-
lock all the side doors and back door can
be changed to a single key turning opera-
tion. For details, contact your Toyota deal-
er.
When all the side doors and back door
are unlocked simultaneously using a key,
the interior light, luggage compartment
light and ignition switch light will come on
and remain on for about 15 seconds be-
fore fading out. (For details, see ªCenter
interior and personal lightsº on page 150,
ªCenter interior lightº on page 151, ªLug-
gage compartment lightº on page 152 and
ªIgnition switch lightº on page 152 in Sec-
tion 1±5.)
The windows and electric moon roof can
be opened or closed with the key opera-
tion in the driver 's door keyhole. (For de-
tails, see ªPower windowsº on page 28
and ªElectric moon roofº on page 40 in
this Section.)
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
The front doors can be opened by pulling
the inside handles even if the lock knobs
are in the locked position.
CAUTION
Do not pull the inside handle of the
front doors while driving. The doors
will open and an accident may occur.
Toyota strongly recommends that all
children be placed in the rear seat of
the vehicle.
Closing the door with the lock knob in the
lock position will also lock the door. Be
careful not to lock your keys in the ve-
hicle.
Doors cannot be locked when either front
door is open and the key is in the igni-
tion.

05_SEQUOIA_U (L/O 0408)
27
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the ve-
hicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the ve-
hicle during an accident. It also helps
prevent the doors from being opened
unintentionally.
You can set the following auto door
locking and unlocking functions.
(a) Locking linked with the shift posi-
tion
All the side doors and back door are
locked automatically when the selector le-
ver is moved out of the ªPº position with
the ignition switch in the ªONº position.
This function is the default setting for new
vehicles.
(b) Unlocking linked with the shift posi-
tion
All the side doors and back door are un-
locked automatically when the selector le-
ver is moved to the ªPº position with the
ignition switch in the ªONº position.
(c) Locking linked with the vehicle
speed
All the side doors and back door are
locked automatically when the vehicle
speed reaches 20 km/h (12 mph) or high-
er. However, if any door is unlocked dur-
ing driving, this auto locking function will
not operate until the unlocked door is
opened once.(d) Unlocking linked with opening the
driver 's door
All the side doors and back door are un-
locked automatically when the driver's
door is opened within 10 seconds after
the ignition switch is turned from ªONº to
the ªACCº or ªLOCKº position.
Setting the functions
1. Close all the side doors and back door.
2. Turn the ignition switch to the ªONº
position.
3. Within 10 seconds after the ignition
switch is turned to the ªONº position;

To set function (a)
Push and hold the front of the driver's
side power door lock switch for 5 sec-
onds with the selector lever in the ªPº
position.

To set function (b)
Push and hold the rear of the driver's
side power door lock switch for 5 sec-
onds with the selector lever in the ªPº
position.

To set function (c)
Push and hold the front of the driver's
side power door lock switch for 5 sec-
onds with the selector lever in any
position except ªPº.
ÐAutomatic door locking and
unlocking functions