automatic transmission fluid TOYOTA SEQUOIA 2001 Service Owner's Guide

DI±584
± DIAGNOSTICSAUTOMATIC TRANSMISSION
778 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0710ATF temperature sensor/Range check (Fluttering)
Related DTCsP0712ATF temperature sensor/Range check (Low resistance)Related DTCs
P0713ATF temperature sensor/Range check (High resistance)
Required sensors/ComponentsATF temperature sensor (TFT sensor)
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not present.See page DI±545
Range check (Fluttering, Low resistance)
The typical enabling condition is not avail-
able.±
Range check (High resistance)
Time after engine start15 min. or more±
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Range check (Fluttering)
TFT (transmission fluid temperature) sensor resistance
Less than 79 W
or
More than 156 kW
Range check (Low resistance)
TFT (transmission fluid temperature) sensor resistanceLess than 79 W
Range check (High resistance)
TFT (transmission fluid temperature) sensor resistanceMore than 156 kW
COMPONENT OPERATING RANGE
ParameterStandard value
TFT (transmission fluid temperature) sensorAtmospheric temperature to approx. 130°C (266°F)

D14157
O E1 Electronically Controlled
Transmission Solenoid
OT±O
OT+
L
OT2±L
OT2+ G±W
G±W
G±WG
B±L
G±W 2
110
9E7
E7
E828 32 24
THO2 THO1
E2ECM
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±585
779 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
AT FLUID TEMP 1
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature when cold soak
HINT:
When DTC P0712 is output and hand±held tester output is 150C (302F) or more, there is a short circuit.
When DTC P0713 is output and hand±held tester output is ±40C (±40F), there is an open circuit.
Measure the resistance between terminal THO1 (OT) and body ground.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
150°C (302°F) or moreShort circuit
HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 second).
When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.

DI±588
± DIAGNOSTICSAUTOMATIC TRANSMISSION
782 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0711 Transmission Fluid Temperature Sensor ºAº
Performance
CIRCUIT DESCRIPTION
See page DI±582.
DTC No.DTC Detection ConditionTrouble Area
P0711
Both (a) and (b) are detected: (2±trip detection logic)
(a) Intake air and engine coolant temps. are more than ±20°C
(±4F) at engine start
(b) After normal driving for over 22 min. and 9 km (6 mile) or
more, ATF temp. is less than 10°C (50F)

Transmission wire (ATF temperature sensor No.1)
MONITOR DESCRIPTION
This DTC indicates that there is a problem with output from the automatic transmission fluid (ATF) tempera-
ture sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF tempera-
ture to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature
and detects an open or short in the ATF temperature circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature
is below 20C (68F) after running the vehicle for a certain period, the ECM interprets this as a fault, and
turns on the MIL.
MONITOR STRATEGY
Related DTCsP0711ATF temperature sensor/Rationality check
Required sensors/ComponentsATF temperature sensor (TFT sensor)
Frequency of operationContinuous
Duration3 sec.
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
TFT (transmission fluid temperature) sen-
sor circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
IAT (Intake air temperature) sensor circuitNot circuit malfunction
Time after engine start21 min. and 40 sec.
Driving distance after engine start9 km (5.6 mile) or more±
IAT (12 sec. after engine start)±10°C (14°F) or more±
ECT (12 sec. after engine start)±10°C (14°F) or more±
DIDJ7±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±589
783 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
TFT (transmission fluid temperature)Less than 20°C (68°F)
(varies with TFT (transmission fluid temperature) at engine start)
WIRING DIAGRAM
See page DI±582.
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
AT FLUID TEMP 1
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature when cold soak
HINT:
When DTC P0712 is output and hand±held tester output is 150C (302F) or more, there is a short circuit.
When DTC P0713 is output and hand±held tester output is ±40C (±40F), there is an open circuit.
Measure the resistance between terminal THO1 (OT) and body ground.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
150°C (302°F) or moreShort circuit
HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 second).
When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.

DI±590
± DIAGNOSTICSAUTOMATIC TRANSMISSION
784 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P0711).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP0711º is outputA
ºP0711º and other DTCsB
HINT:
If any other codes besides ºP0711º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A
2 Check transmission fluid level (See page DI±524).
OK:
Automatic transmission fluid level is correct.
NG Add fluid
(See page DI±524).
OK
Replace the transmission wire (ATF tempera-
ture sensor) (See page AT±7).

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±657
851 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
Related DTCsP2714Shift solenoid valve SLT/ON malfunction
MainShift solenoid valve SLT
Required sensors/ComponentsSubValve body, ATF temperature sensor, Speed sensor (NT), Speed sensor
(NO)
Frequency of operationContinuous
DurationImmediate
MIL operation2 driving cycles
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Turbine speed sensor circuitNot circuit malfunction
Output speed sensor circuitNot circuit malfunction
Transmission Fluid Temperature Sensor
circuitNot circuit malfunction
Shift solenoid valve S1 circuitNot circuit malfunction
Shift solenoid valve S2 circuitNot circuit malfunction
Shift solenoid valve SR circuitNot circuit malfunction
Shift solenoid valve SL1 circuitNot circuit malfunction
Shift solenoid valve SL2 circuitNot circuit malfunction
Shift solenoid valve SLT circuitNot circuit malfunction
ECT (Engine coolant temperature) sensor
circuitNot circuit malfunction
KCS sensor circuitNot circuit malfunction
ETCS (Electric throttle control system)Not system down
Transmission rangeºDº
ECT40°C (104°F) or more±
Spark advance from Max. retard timing by
KCS control0° CA or more±
EngineStarting
Transfer rangeºHIGHº*1
TFT (transmission fluid temperature)10°C or more±
Transfer range ºHIGHº *1 (This condition is applied only 4WD)
*1 Following conditions met
Vehicle speed sensor circuitNot circuit malfunction
Output shaft speed sensor circuitNot circuit malfunction
Transfer output speed143 rpm or more±
NO/NOtf (Transfer input speed/Transfer
output speed)0.9 to 1.1

DI±666
± DIAGNOSTICSAUTOMATIC TRANSMISSION
860 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2740 Transmission Fluid Temperature Sensor ºBº
Circuit
DTC P2742 Transmission Fluid Temperature Sensor ºBº
Circuit Low Input
DTC P2743 Transmission Fluid Temperature Sensor ºBº
Circuit High Input
CIRCUIT DESCRIPTION
ATF (Automatic Transmission Fluid) temperature sensor No.2 is on the transmission and just in front of the
oil cooler inlet pipeline.
If ECM detects the abnormally high temperature of ATF by this sensor, it draws driver's attention by illuminat-
ing the warning lamp.
HINT:

The temperature of ATF easily rises when towing, climbing hills and in traffic, etc.

If the ATF temperature sensor No.2 becomes short±circuited, the signal that indicates the ATF temper-
ature is 150C (302F) or higher is input in ECM.
Vehicle conditions when the sensor is normal and when the sensor is short±circuited are indicated
in the table below.
ATF temperature Sensor No.2
StateDetection ConditionSymptomRecovery Condition

AT fluid temp. more than 150C
(302F).
AT Oil Temp. warning light re-
mains on
AT fluid temp. less than 135C
(275F). *2

AT fluid temp. more than 130C
(266F).
Shift point too high.
AT fluid temp. less than 110C
(230F).
Sensor is normalWhen the conditions (a) and (b)
are satisfied.
(a) AT fluid temp. more than 130C
(266F).
(b) Engine coolant temp. more
than 95C (203F).

Lock±up at 3rd gear. *1
AT fluid temp. less than 110C
(230F) *2 and engine coolant
temp. less than 95C (203F).
Sensor is short±circuited

Any conditions.

AT Oil Temp. warning light re-
mains on

Shift point too high.

Symptoms still occur
Sensor is short circuited

Engine coolant temp. more than
95C (203F).
Lock±up at 3rd gear. *1
Symptoms still occur
HINT:
*1: When AT fluid temperature is normal, transmission locks up at 5th gear with the shift lever in D position
and at 4th gear with the shift lever in 4 position.
*2: When AT fluid temperature is in normal range, it decreases to less than 135C (275F) within 5 minutes
with the shift lever in P or N position in an idling state.
DIDJN±01

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±667
861 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P2740
(a) and (b) are detected momentarily within 0.5 sec. when
neither P2742 nor P2743 is detected (1±trip detection logic)
(a) ATF temperature sensor No.2 resistance is less than 25 W
(0.046 V)
(b) ATF temperature sensor No.2 resistance is more than 156
kW (4.915 V)
HINT:
Within 0.5 sec. the malfunction switches from (a) to (b) or from
(b) to (a)

Open or short in ATF temperature sensor No.2 circuit

Transmission wire (ATF temperature sensor No.2)

ECM
P2742ATF temperature sensor No.2 resistance is less than 25 W
(0.046 V) for 0.5 sec. or more (1±trip detection logic)
Short in ATF temperature sensor No.2 circuit

Transmission wire (ATF temperature sensor No.2)

ECM
P2743
ATF temperature No.2 sensor resistance is more than 156 kW
(4.915 V) when 15 minutes or more after the engine start
DTC is detected for 0.5 sec. or more (1±trip detection logic)
Open in ATF temperature sensor No.2 circuit

Transmission wire (ATF temperature sensor No.2)

ECM
MONITOR DESCRIPTION
The Automatic Transmission Fluid (ATF) temperature sensor converts ATF temperature to an electrical re-
sistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects
an open or short in the AFT temperature circuit. If the resistance value of the ATF temperature is less than
25 W (0.046 V) or more than 156 kW (4.915 V), the ECM interprets this as a fault in the ATF sensor or wiring.
The ECM will turn on the MIL and store the DTC.
MONITOR STRATEGY
P2740ATF temperature sensor/Range check (Fluttering)
Related DTCsP2742ATF temperature sensor/Range check (Low voltage)Related DTCs
P2743ATF temperature sensor/Range check (High voltage)
Required sensors/ComponentsATF temperature sensor (TFT sensor)
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not present.See page DI±545
Range check (Fluttering, Low voltage)
The typical enabling condition is not avail-
able.±
Range check (High voltage)
Time after engine start15 min. or more±

D14157
O E1 Electronically Controlled
Transmission Solenoid
OT±O
OT+
L
OT2±L
OT2+ G±W
G±W
G±WG
B±L
G±W 2
110
9E7
E7
E828 32 24
THO2 THO1
E2ECM DI±668
± DIAGNOSTICSAUTOMATIC TRANSMISSION
862 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Range check (Fluttering)
TFT (transmission fluid temperature) sensor voltage
Less than 0.046 V
or
More than 4.915 V
Range check (Low voltage)
TFT (transmission fluid temperature) sensor voltageLess than 0.046 V
Range check (High voltage)
TFT (transmission fluid temperature) sensor voltageMore than 4.915 V
COMPONENT OPERATING RANGE
ParameterStandard value
TFT (transmission fluid temperature) sensorAtmospheric temperature to approx. 130°C (266°F)
WIRING DIAGRAM

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±669
863 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand±held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the ºONº button of the OBD II scan tool or the hand±held tester.
(f) When you use the hand±held tester:
Select the item ºDIAGNOSIS / ENHANCED OBD II / DATA LISTº.
(g) According to the display on the tester, read the ºDATA LISTº.
ItemMeasurement Item/
Range (display)Normal Condition
AT FLUID TEMP 2
ATF Temp. Sensor Value/
min.: ±40C (±40F)
max.: 215C (419F)
After Stall Test;
Approx. 80C (176F)

Equal to ambient temperature when cold soak
HINT:
When DTC P2742 is output and hand±held tester output is 150C (302F) or more, there is a short circuit.
When DTC P2743 is output and hand±held tester output is ±40C (±40F), there is an open circuit.
Measure the resistance between terminal THO2 (OT2) and body ground.
Temperature DisplayedMalfunction
±40°C (±40°F)Open circuit
150°C (302°F) or moreShort circuit