display TOYOTA SEQUOIA 2001 Service Owner's Guide

DI±122
± DIAGNOSTICSENGINE
316 Author: Date:
2005 SEQUOIA (RM1146U)
1 Connect hand±held tester, and read value of engine coolant temperature.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / COOLANT TEMP.
CHECK:
Read the temperature value on the the hand±held tester.
OK:
Same value as actual engine coolant temperature.
RESULT:
Displayed TemperatureProceed to
±40°C (±40°F)A
140°C (284°F) or moreB
OK (Same as present temperature)C
HINT:

If there is an open circuit, hand±held tester indicates ±40°C (±40°F).

If there is a short circuit, hand±held tester indicates 140°C (284°F) or more.
B Go to step 4.
C Check for intermittent problems
(See page DI±11).
A

± DIAGNOSTICSENGINE
DI±129
323 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detection Condition
Condition (a) of DTC P0120, P0122, P0123, P0220, P0222 or P0223 continues
for 2 sec.
(Open or short in the throttle control motor and sensor circuit)Trouble Area
P0120
Detection conditions for DTCs P0122 and P0123 are not satis-
fied but condition (a) is satisfied
(a) VTA1 is º0.2 V or lessº or VTA1 is º4.8 V or moreº
Open or short in throttle control motor and sensor circuit

Throttle control motor and sensor

ECM
P0122(a) VTA1 is 0.2 V or less

Short in throttle control motor and sensor circuit

Throttle control motor and sensor

Short in VTA1 circuit

Open in VC circuit

ECM
P0123(a) VTA1 is 4.8 V or more

Open in throttle control motor and sensor circuit

Throttle control motor and sensor

Open in VTA1 circuit

Open in E2 circuit

VC and VTA1 circuit are short±circuited

ECM
P0220
Detection conditions for DTCs P0222 and P0223 are not satis-
fied but condition (a) is satisfied
(a) VTA2 is º0.5 V or lessº or VTA2 is º4.8 V or moreº
Throttle control motor and sensor

ECM
P0222(a) VTA2 is 0.5 V or less

Throttle control motor and sensor

Short in VTA2 circuit

Open in VC circuit

ECM
P0223(a) VTA2 is º4.8 V or moreº and
VTA1 is º0.2 V or moreº and VTA1 is º1.8 V or lessº

Throttle control motor and sensor

Open in VTA2 circuit

Open in E2 circuit

VC and VTA2 circuit are short±circuited

ECM
P2135
Condition (a) continues for 0.5 sec. or more, or
condition (b) continues for 0.4 sec. or more:
(a) Difference between VTA1 and VTA2 is 0.02 V or less
(b) VTA1 is º0.2 V or lessº and VTA2 is º0.5 V or lessº
VTA1 and VTA2 circuit are short±circuited

Throttle control motor and sensor

ECM
HINT:

After confirming DTCs, use the hand±held tester or the OBD II scan tool to confirm the throttle valve
opening percentage and closed throttle position switch condition.

THROTTLE POS means the VTA1 signal and the THROTTLE POS #2 means the VTA2 signal.
Reference (Normal condition):
Tester displayAccelerator pedal fully releasedAccelerator pedal fully depressed
THROTTLE POS10 to 24%66 to 98%
THROTTLE POS #22.1 to 3.1 V4.5 to 5.5 V

± DIAGNOSTICSENGINE
DI±133
327 Author: Date:
2005 SEQUOIA (RM1146U)
1 Connect hand±held tester, and read the voltage for throttle position sensor data.
PREPARATION:
(a) Enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / THROTTLE POS
and THROTTLE POS #2.
CHECK:
Read voltage value displayed on the hand±held tester.
OK:
RESULT:
Throttle position expressed as percentage and voltage
Accelerator pedal releasedAccelerator pedal depressedTrouble areaProceed toTHROTTLE POS
(VTA1)THROTTLE POS #2
(VTA2)THROTTLE POS
(VTA1)THROTTLE POS #2
(VTA2)Trouble areaProceed to
0 %0 to 0.2 V0 %0 to 0.2 VVC circuit open
100 %4.5 to 5.5 V100 %4.5 to 5.5 VE2 circuit open
0 % or 100 %2.1 to 3.1 V
(Fail safe)0 % or 100 %2.1 to 3.1 V
(Fail safe)VTA1 circuit open or
ground shortA
about 16 %
(Fail safe)0 to 0.2 or 4.5 to 5.5 Vabout 16 %
(Fail safe)0 to 0.2 or 4.5 to 5.5 VVTA2 circuit open or
ground short
10 to 24 %2.15 to 3.05 V64 to 96 %
(Does not fail safe)4.5 to 5.5 V
(Does not fail safe)Throttle position sen-
sor circuit is normalB
B Go to step 5.
A

B17411
E2 VC
E8ECM Connector
± DIAGNOSTICSENGINE
DI±135
329 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check voltage between terminals VC and E2 of ECM connector.
PREPARATION:
(a) Disconnect the T14 throttle control motor and sensor con-
nector.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between the specified terminals of the E8
ECM connector.
OK:
Standard:
Tester ConnectionSpecified Condition
VC (E8±23) ± E2 (E8±28)4.5 to 5.5 V
NG Replace ECM (See page SF±80).
OK
4 Replace throttle body (See page SF±42).
Go
5 Check if DTC output recur.
PREPARATION:
(a) Clear the DTC (See page DI±43).
(b) Start the engine.
(c) Run the engine at idle for 15 seconds or more.
CHECK:
Read the DTC.
RESULT:
Display (DTC Output)Proceed to
ºP0120, P0122, P0123, P0220, P0222, P0223 and/or P2135º are output
againA
No DTC outputB
B System is OK.
A

DI±140
± DIAGNOSTICSENGINE
334 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Fuel cutOFF
EngineRunning
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Time until ºengine coolant temperatureº detection temperature reaches feedback start temperature
When the temperature at the time of engine starting is
±8.34°C (17°F) or moreEngine coolant temperature is less than ºclosed±loop enable temperatureº
when 2 min. or more after engine start
When the temperature at the time of engine starting is
±19.45 to ±8.34°C (±3 to 17°F)Engine coolant temperature is less than ºclosed±loop enable temperatureº
when 5 min. or more after engine start
When the temperature at the time of engine starting is
±19.45°C (±3°F) or lessEngine coolant temperature is less than ºclosed±loop enable temperatureº
when 20 min. or more after engine start
INSPECTION PROCEDURE
HINT:

If DTC P0115, P0116, P0117, P0118 and P0125 are output simultaneously, engine coolant tempera-
ture sensor circuit may be open or short. Perform the troubleshooting of DTC P0115, P0117 or P0118
first.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, as well as other data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0125) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTCs using the hand±held tester.
RESULT:
Display (DTC output)Proceed to
P0125A
ºP0125º and other DTCsB
HINT:
If any other codes besides ºP0125º are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI±58).
A

DI±144
± DIAGNOSTICSENGINE
338 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR RESULT
Refer to page DI±26 for detailed information.
The test value and test limit information are described as shown in the following table. Check the monitor
result and test values after performing the monitor drive pattern (refer to ºConfirmation Monitorº).

MID (Monitor Identification Data) is assigned to each emissions±related component.

TID (Test Identification Data) is assigned to each test value.

Scaling is used to calculate the test value indicated on generic OBD ll scan tools.
Thermostat
MIDTIDScalingDescription of Test ValueMinimum Test LimitMaximum Test Limit
$E1$E8Multiply by 0.1
(°C)ECT sensor output when estimated
ECT reached to malfunction criteriaMalfunction criterionMaximum test limit
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0128) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P0128A
P0128 and other DTCsB
HINT:
If any other codes besides P0128 are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI-58).
A

+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Case 1
Case 2
Case 3
Case 4
Output voltage of A/F sensor
(sensor 1: front sensor)
Injection volume
Output voltage
Output voltage of heated oxygen
sensor (sensor 2: rear sensor)Mainly suspected
trouble area
OK
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
Sensor 1: front sensor
(sensor 1, heater, sensor 1
circuit)
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NGExtremely rich or lean actual
air±fuel ratio
(Injector, fuel pressure, gas
leakage in exhaust system,
etc.) OK
OK
OK
Almost
no reaction
'
Sensor 2: rear sensor
(sensor 2, heater, sensor 2
circuit)
Almost
no reactionAlmost
no reactionAlmost
no reaction
DI±156
± DIAGNOSTICSENGINE
350 Author: Date:
2005 SEQUOIA (RM1146U)
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of
the heated oxygen sensors.
For displaying the graph indication, first enter ºACTIVE TEST / A/F CONTROL / USER DATA,º then select
ºA/F B1,2S1and O2S B1,2S2º by pressing ºYESº button, and push ºENTERº button before pressing ºF4º
button.
HINT:

If different DTCs that are related to different system are output simultaneously while terminal E2 is used
as a ground terminal, terminal E2 may be open.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. when
a malfunction occurred.

± DIAGNOSTICSENGINE
DI±157
351 Author: Date:
2005 SEQUOIA (RM1146U)
1 Read output DTC.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P0138, P0158A
P0137, P0157B
P0136, P0156C
HINT:
If any other codes besides P0136, P0137, P0138, P0156, P0157 and/or P0158 are output, perform the trou-
bleshooting for those DTCs first.
B Go to step 14.
C Go to step 7.
A
2 Check output voltage of heated oxygen sensor.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) After warming up the engine, run the engine at 2,500 rpm for 3 minutes.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / O2S B1S2 or B2S2.
(d) Allow the engine to idle.
CHECK:
Read the Heated Oxygen (HO2) sensor output voltage while idling.
RESULT:
HO2 Sensor Output VoltagesProceed To
More than 1.2 VA
Less than 1.0 VB
B Go to step 5.
A

± DIAGNOSTICSENGINE
DI±159
353 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check whether DTC output recurs (DTC P0138, P0158)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0138 or P0158A
No outputB
B Check for intermittent problems
(See page DI±11).
A
Replace heated oxygen sensor.
7 Check output voltage of heated oxygen sensor.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Start the engine.
(d) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / O2S B1S2.
(e) After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.
CHECK:
(a) Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
HINT:
Quickly accelerate the engine to 4,000 rpm 3 times using the accelerator pedal.
Standard: Fluctuates between 0.4 V or less and 0.5 V or more.
NG Go to step 14.
OK
8 Perform confirmation driving pattern.
NEXT

DI±160
± DIAGNOSTICSENGINE
354 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check whether DTC output recurs (DTC P0136, P0156)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0136 or P0156A
No outputB
B Check for intermittent problems
(See page DI±11).
A
10 Replace heated oxygen sensor.
NEXT
11 Perform confirmation driving pattern.
NEXT
12 Check whether DTC output recurs (DTC P0136, P0156)
CHECK:
(a) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
(b) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P0136 or P0156A
No outputB
B Repair completed.
A