key TOYOTA SEQUOIA 2001 Service Workshop Manual

DID8S±01
/ /
/ /
COMBINATION METER SYSTEM Check Sheet
Inspector 's name:
Customer 's NameVIN
Production Date
Licence Plate No.
Date Vehicle
Brought InOdometer Readingkm
miles
Weather Conditions
When Problem
OccurredFrequency Problem Occurs
Weather
Outside temperature Constantly  Sometimes ( times per day, month)
 Once only Date Problem First Occurred
 Fine  Cloudy  Rainy  Snowy
 Various/Others
 Hot  Warm  Cool
 Cold (Approx. 5F ( 5C))
Problem Symptom
Gauge

Malfunction in speedometer

Malfunction in tachometer

Malfunction in engine coolant temperature receiver gauge

Malfunction in fuel receiver gauge

Entire combination meter does not operate

Buzzer does not sound (Key reminder warning, Seat belt warning)

Seat belt warning for driver's seat does not operate
Others

Operating light control rheostat does not change light brightness

















Malfunction in oil pressure receiver gauge

Malfunction in volt meter DI±1612
± DIAGNOSTICSCOMBINATION METER SYSTEM
1806 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK

DID8T±01
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1613
1807 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMIZE PARAMETERS
HINT:
The following can be customized.
NOTICE:

After confirming whether the items of the customer's request are applicable or not as custom-
ized items, perform customization.

Be sure to record the current value before customizing.

When troubleshooting, pay attention as there is a possibility that the function has been set to
SMALL through customizing (Example: In case of the symptom in which ºThe key reminder
buzzer operation does not functionº is displayed, check that the key reminder buzzer operation
is not set to SMALL, then perform troubleshooting).
METER:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
KEY REMND VOLUM
(Key reminder buzzer vol-
ume)
LARGEFunction that changes the volume of key reminder buzzer.LARGE/MEDIUM/SMALL

DID8U±01
DI±1614
± DIAGNOSTICSCOMBINATION METER SYSTEM
1808 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
Inspect the related ºFuseº and ºRelayº before confirming the suspected area as shown in the table below.
MALFUNCTION SYSTEM:
SymptomSuspected AreaSee page
Entire combination meter does not operate.Refer to troubleshooting proceduresDI±1628
Operating light control rheostat does not change light brightness.Refer to troubleshooting proceduresDI±1645
Seat belt warning does not operate.Refer to troubleshooting proceduresDI±1650
Key reminder warning buzzer does not sound.
1. Multiplex communication system
2. Key unlock warning switch circuit
3. Door courtesy lamp switch circuit
4. Combination meter assyDI±1892
DI±1715
DI±1728
IN±35
METER GAUGES:
SymptomSuspected AreaSee page
Malfunction in speedometerRefer to troubleshooting proceduresDI±1632
Malfunction in tachometerRefer to troubleshooting proceduresDI±1636
Malfunction in fuel receiver gaugeRefer to troubleshooting proceduresDI±1640
Malfunction in engine coolant temperature receiver gaugeRefer to troubleshooting proceduresDI±1644
Malfunction in oil pressure receiver gaugeRefer to troubleshooting proceduresDI±1654
Malfunction in volt meterRefer to troubleshooting proceduresDI±1658
WARNING LIGHTS:
SymptomSuspected AreaSee page
Check engine warning light (MIL) does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Discharge warning light does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Brake warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
ABS warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
SRS warning light does not come on.
1. Airbag sensor assy
2. Wire harness or connector
3. Combination meter assyDI±1126
±
IN±35
Open door warning light does not come on.
1. Door courtesy light switch circuit
2. Wire harness or connector
3. Combination meter assy
4. Body ECUDI±1728
±
IN±35
IN±35
Fuel level warning light does not come on.
1. Refer to troubleshooting
2. Wire harness or connector
3. Combination meter assyDI±1640
±
IN±35
Low oil pressure warning light does not come on.
1. Low oil pressure warning switch
2. Wire harness or connector
3. Combination meter assyBE±55
±
IN±35

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1615
1809 Author: Date:
2005 SEQUOIA (RM1146U) Seat belt warning lamp for driver's seat does not operate.
Refer to troubleshooting proceduresDI±1650
SLIP warning light does not come on.
1. SLIP warning light circuit
2. Wire harness and connector
3. Combination meter assy
4. Skid control ECUDI±1041
±
IN±35
IN±35
INDICATOR LIGHTS:
SymptomSuspected AreaSee page
Turn indicator light does not come on.
1. Turn signal flasher relay
2. Wire harness or connector
3. Combination meter assyBE±36
±
IN±35
High beam indicator light does not come on.
1. Headlight dimmer switch (*1)
Headlight dimmer switch circuit (*2)
2. Wire harness or connector
3. Combination meter assyBE±27
DI±1755
±
IN±35
Washer level indicator light does not come on.
1. Washer level warning switch
2. Wire harness or connector
3. Combination meter assyBE±49
±
IN±35
Tire pressure indicator light does not come on.
1. Tire pressure monitor ECU
2. Wire harness or connector
3. Combination meter assyDI±873
±
IN±35
CRUISE main indicator light does not come on.
1. CRUISE main indicator light circuit
2. Cruise main control switch circuit
3. Wire harness or connector
4. Combination meter assyDI±1557
DI±1561
±
IN±35
VSC OFF indicator light does not come on.1. VSC OFF indicator light circuit
2. Combination meter assyDI±1048
IN±35
VSC TRAC indicator light does not come on.1. VSC TRAC indicator light circuit
2. Combination meter assyDI±1027
IN±35
Security indicator light does not come on.1. Security indicator light circuit
2. Combination meter assyDI±1731
IN±35
4HI indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
4LO indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
CTR DIF LOCK indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
Height control indicator lamp does not come on.1. Height control indicator lamp circuit
2. Combination meter assyDI±785
IN±35
Height control manual indicator lamp does not come on.1. Height control manual indicator lamp circuit
2. Combination meter assyDI±789
IN±35
A/T indicator light does not come on.
1. Park/neutral position switch circuit
2. Wire harness and connector
3. Combination meter assyDI±576
±
IN±35
*1: w/o Day time running light
*2: w/ Day time running light
OTHERS:
SymptomSuspected AreaSee page
All buzzers (key reminder, seat belt) do not operate.Combination meter assyIN±35

Wire harness side
1
2
3
4
5
6
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
401
2
3
4
5
8 6
10
11
12
13
14
15
16
17
18
19
21
23
24
Terminal No.
Translate ECU
ECM
STA Fuse
Front Seat Inner Belt LH (Buckle Switch)
Overhead Module (Garage Door Opener)
Overhead Module (Garage Door Opener)
Washer Level Sensor
ECM
ECM (*1)
Transponder Key Computer
Body ECU
ECM
ECM
Tire Pressure Monitor ECU
Injector No. 1
Light Control Rheostat
ECM
Speed Sensor
4P OUT (Other Parts)
Fuel Sender Gauge
Oil Pressure Sender Gauge
IGN Fuse
Airbag Sensor Assembly
Memory Seat ECU and SW (*2)
Back Door ECU
Integration Control and Panel
Turn Signal Flasher Relay
Park/Neutral Position Switch
Airbag Sensor AssemblyTranslate ECU
Translate ECU
Skid Control ECU
4WD Control ECU
Alternator
Speed Sensor
Fuel Sender Gauge
Ground
Suspension Control ECU
Body ECU (*4)
Body ECU (*3)
Turn Signal Flasher Relay
Skid Control ECU
ECU±B Fuse
IGN1 Fuse Connectors:
Terminal No.
Wire harness side
C5
C64WD Control ECU
4WD Control ECU
Suspension Control ECU
Suspension Control ECU
Suspension Control ECU
*1: 4WD
*2: w/ Driving Position Memory
*3: w/ Daytime Running Light
*4: w/o Daytime Running LightPark/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch DI±1624
± DIAGNOSTICSCOMBINATION METER SYSTEM
1818 Author: Date:
2005 SEQUOIA (RM1146U)

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1627
1821 Author: Date:
2005 SEQUOIA (RM1146U)
ACTIVE TEST
Performing the ACTIVE TEST using the hand±held tester allows the meters, indicators and so on to operate
without part removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten
labor time.
It is possible to display the DATA LIST on the hand±held tester during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
SPEED METER
Operate speedometer: 0 / 40 (24) / 80 (48) / 120
(72) / 160 (96) /
200 (120) km/h (mph)The needle position should be within the accept-
able tolerance
TACHOMETER
Operate tachometer:
0 rpm / 1,000 rpm / 2,000 rpm / 3,000 rpm /
4,000 rpm / 5,000 rpm / 6,000 rpm / 7,000 rpmConfirm that the vehicle is stopped and engine is
idling.
FUEL GAUGEOperate fuel gauge: EMPTY, 1/2, FULLConfirm that the vehicle is stopped and engine is
idling.
COOLANT TEMPOperate engine coolant temperature receiver
gauge: HIGH / NORMAL / LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
D BELT REMINDOperate driver's seat belt warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
OPEN DOOR WARNOperate open door warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
LOW FUEL WARNOperate fuel level warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
TAILLIGHT INDICOperate taillight indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
HEADLIGHT INDICOperate Hi±beam indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
SRS WARNOperate SRS warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
ODO/TRIP DISPOperate ODO/TRIP display: OFF / ONConfirm that the vehicle is stopped and engine is
idling.
KEY REMND BUZZROperate key reminder buzzer: OFF / ONConfirm that the vehicle is stopped and engine is
idling.
SEAT BELT BUZZROperate driver's seat belt warning buzzer:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
MAINT REQDOperate oil maintenance indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
VOLT METEROperate volt meter: 9 V / 12 V / 15 V / 18VConfirm that the vehicle is stopped and engine is
idling.
OIL PRESS METEROperate oil pressure meter: HIGH, 3/4, 1/2, 1/4,
LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.

DID98±01
I28587
From Battery Driving Position Memory Switch BODY ECU
Courtesy SW (D)
MM
Remote Control Mirror Switch
RHOuter
Mirror LH
(Retract
Motor) M1
M2 MM
M1 DCTY
PCTY
RRCY
RLCY
HCTY
KSW
LSWR
LSWL
PKB
WIG
IG
ACC
BECU
S+B
BDRACT+
ACTD
ACT±M2
MIRB
MIRS
MIRFM+
MSW
EB
MF
E2MR
Door Lock Motor
Front
LHFront
RHRear
LHRear
RH
Courtesy SW (P)
Courtesy SW (RR)
Courtesy SW (RL)
Hood Courtesy SW
Key Unlock Warning SW
Door Unlock Detection
SW Rear RH
Door Unlock Detection
SW Rear LH
Parking Brake SW
Battery AM1ALTACC IG1 Ignition SwitchWSH
ECU±IG
RAD No. 2
ECU±B
DOOR No. 2SECURITY
HORN AM1
± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1679
1873 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DI1OE±19
Inspector 's name:
Customer 's Name
Date VehicleVIN
Licence Plate No.
Production Data
Odometer Reading / /km
mile
Weather Conditions
When Problem
Occurred
Date Problem First Occurred
Frequency Problem Occurs
Weather
/ /
Once only Brought in
Malfunction
System
Outdoor Temperature
Fine Cloudy Rainy Snowy
Various/Others
Hot Warm Cool
Cold (Approx. °F ( °C))
Constant Sometimes ( times per day, month)
Key Unlock Warning System
Headlight and Taillight System (Light Auto Turn±off system, Daytime Running
Light System
Stop Light System
Automatic Light Control System
Illuminated Entry System
Foglight System
Wiper and Washer System
Power Window Control System
Power Door Lock Control System
Theft Deterrent System
Wireless Door Lock Control System
Others (Buzzer etc.)
Auto Lock/Unlock System BODY CONTROL SYSTEM Check Sheet
Remote Control Mirror System (w/ Driving Position Memory)
± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1683
1877 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK

DID9A±01
DI±1684
± DIAGNOSTICSBODY CONTROL SYSTEM
1878 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMIZE PARAMETERS
HINT:
The following items can be customized.
NOTICE:

When the customer requests a change in a function, first make sure that customization of the
function(s) is/are possible.

Be sure to make a note of the current setting before customizing.

When troubleshooting a function, first make sure that the function is not set to OFF.
WIRELESS DOOR LOCK:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
WIRELESS OPERONTurns wireless door lock function ON/OFF.ON/OFF
OPEN DOOR WARNONSounds buzzer for 10 seconds when door is not completely
closed and transmitter LOCK switch is pressed.ON/OFF
AUTO LOCK DELAY30SControls amount of time from when doors are unlocked until
they are locked by automatic lock function.60S/30S
UNLOCK/2OPERON
When UNLOCK switch is pressed once, this function un±
locks only the designated door. When unlock switch is
pressed again within 3 seconds, all doors unlock. If setting is
OFF, pressing UNLOCK switch once unlocks all doors.
ON/OFF
LNT/LGT ON/UNLKONTurns on room light when wireless door lock system is oper-
ated.ON/OFF
ALARM FUNCTIONONOperates theft deterrent system when transmitter LOCK
(PANIC) switch is held for 3 seconds.ON/OFF
AUTO LOCKOFFLocks doors when the vehicle speed reaches a certain level.ON/OFF
UNLK/KEY TWICEON
Unlocks only driver's door when driver's door key cylinder is
turned to unlock once, and unlocks all doors when it is turned
to unlock twice. In OFF setting, unlocks all doors when the
cylinder is turned to unlock once.
ON/OFF
ALL UNLK/OPN±CLOFFFunction that unlocks all doors when the driver door is
opened after turning the ignition switch off.ON/OFF
UNLOCK/PARKOFFUnlocks doors when shift lever is moved to P position from
any position other than P while the ignition switch is ON.ON/OFF
THEFT:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
WARNING TIME15SChanges warning time for PASSIVE MODE.5S/15S/27.5S/60S
PASSIVE MODEOFF
Switches theft deterrent system from arming preparation
state to armed state 30 seconds after key is removed from
ignition key cylinder and driver side door is closed, even if
doors are not locked by wireless or door key lock operation.
ON/OFF
WARN BY GLS SENONFunction that switches the alarm warning on/off when glass
breakage is detected.ON/OFF
DOOR LOCK:
DISPLAY (ITEM)DEFAULTCONTENTSSETTING
AUTO LOCK/SHIFTONLocks doors when shift lever is moved from P to another
position.ON/OFF

DI1OH±18
DI±1686
± DIAGNOSTICSBODY CONTROL SYSTEM
1880 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
DOOR LOCK CONTROL
SymptomSuspected AreaSee page
Lock or unlock cannot be operated with door lock control switch.
1. Door lock control switch (Power source circuit)
(Driver's)
(Passenger's)
2. Body ECU
DI±1788
DI±1826
IN±35
Door key linked function does not operate.
1. Door key lock and unlock switch circuit (Driver's)
(Passenger's)
2. Body ECUDI±1794
DI±1832
IN±35
Key confinement prevention function does not operate.1. Key unlock warning switch circuit
2. Body ECUDI±1715
IN±35
Door lock function does not operate.1. Door lock motor circuit
2. Body ECUDI±1720
IN±35
THEFT DETERRENT SYSTEM
SymptomSuspected AreaSee page
No alerting condition is operated. (The system cannot be set.)
1. Security indicator circuit
2. Key unlock warning switch circuit
3. Courtesy light switch circuit
4. Door unlock detection switch circuit (Driver's)
(Passenger's)
5. Engine hood courtesy light switch circuit
6. Back door courtesy light switch circuit
7. Back door ECU
8. Body ECUDI±1731
DI±1715
DI±1728
DI±1791
DI±1829
DI±1725
DI±1864
IN±35
IN±35
Cannot be canceled when IG is turned ON with a key.
1. Key unlock warning switch circuit
2. Ignition switch
3. Body ECUDI±1715
BE±24
IN±35
Cannot be canceled when unlocking the back door with a key.1. Back door ECU
2. Body ECUIN±35
IN±35
Headlights do not light up as an alert function.1. Headlight relay circuit
2. Body ECUDI±1708
IN±35
Taillights do not light up as an alert function.1. Taillight relay circuit
2. Body ECUDI±1706
IN±35
Theft deterrent horn or vehicle horn does not sound.
1. Security horn circuit
2. Horn circuit
3. Body ECUDI±1734
DI±1764
IN±35
During warning condition, cannot be canceled by unlocking the
door with a key.1. Door key lock and unlock switch circuit (Driver's)
(Passenger's)
2. Body ECUDI±1794
DI±1832
IN±35
During warning condition, cannot be canceled by unlocking the
door with a key. (transmitter)1. Transmitter
2. Body ECUBE±99
IN±35
During warning condition, cannot be canceled by turning the igni-
tion ON with a key.1. Ignition switch
2. Key unlock warning switch circuit
3. Body ECUBE±24
DI±1715
IN±35
The system operated for more than 60 seconds.Body ECUIN±35
Glass breakage sensor does not operate.1. Glass breakage sensor circuit
2. Body ECUDI±1774
IN±35