battery TOYOTA SEQUOIA 2001 Service Manual PDF

DI±292
± DIAGNOSTICSENGINE
486 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0560 System Voltage
MONITOR DESCRIPTION
The battery supplies electricity to the ECM even when the ignition switch is OFF. This electricity allows the
ECM to store data such as DTC history, freeze frame data, fuel trim values, and other data.
If the battery voltage falls below a minimum level, the ECM will conclude that there is a fault in the power
supply circuit. The next time the engine starts, the ECM will turn on the MIL and a DTC will be set.
DTC No.DTC Detecting ConditionTrouble Area
P0560Open in back up power source circuit

Open in back±up power source circuit

EFI fuse

ECM
HINT:
If DTC P0560 present, the ECM will not store another DTC.
MONITOR STRATEGY
Related DTCsP0560System voltage malfunction
Required sensors/componentsECM
Frequency of operationContinuous
Duration3 sec.
MIL operationImmediate (*1)
Sequence of operationNone
*1: The DTC is set immediate. The MIL will be illuminated after the engine starts in the next time.
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Stand±by RAMInitialized
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Battery voltageLess than 3.5 V
DICF7±02

A05652A18100
Battery2DEFI No. 1
B±Y
E4ECM
BATT 73
2H 1
IA411
B±Y B
F10
Fusible Link
Block 4Engine Room J/B
5
B12
± DIAGNOSTICSENGINE
DI±293
487 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check battery voltage.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Select the item: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / BATTERY VOLTAGE.
CHECK:
Read the battery voltage on the hand±held tester
RESULT:
Battery voltageProceed to
0 VA
Except 0 VB
B Go to step 5.
A

A21381
Engine Room J/B
EFI No. 1 Fuse
B17417
E4
BATT ECM Connector
± DIAGNOSTICSENGINE
DI±295
489 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check for open and short in harness and connector between ECM and EFI No. 1
fuse, EFI No. 1 fuse and battery.
PREPARATION:
(a) Remove the EFI No. 1 fuse from the engine room J/B.
(b) Disconnect the E4 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tor.
OK:
Standard:
Tester ConnectionSpecified Condition
Engine Room J/B (EFI No. 1 fuse
terminal 2) ± BATT (E4±3)Below 1 W
Engine Room J/B (EFI No. 1 fuse
terminal 2) or BATT (E4±3) ±
Body ground
10 kW or higher
NG Repair or replace harness or connector.
OK
5 Check the battery (See page CH±1).
NG Replace battery.
OK
Check and replace engine room J/B.

DI±298
± DIAGNOSTICSENGINE
492 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0617 Starter Relay Circuit High
MONITOR DESCRIPTION
While the engine is being cranked, the battery positive voltage is applied to terminal STA of the ECM.
If the vehicle is being driven and the ECM detects the starter control signal (STA), the ECM concludes that
the starter control circuit is malfunctioning. The ECM will turn on the MIL and a DTC is set.
DTC No.DTC Detection ConditionTrouble Area
P0617
When all conditions (a), (b) and (c) are satisfied for 20 seconds
with battery (+B) voltage 10.5 V or more
(a) Vehicle speed
20 km/h (12.4 mph)
(b) Engine revolution
1,000 rpm
(c) STA signal ON
Park/neutral position switch

Starter relay circuit

Ignition switch

ECM
MONITOR STRATEGY
Related DTCsP0617Starter signal error
Rid / tMain sensors/componentsStarter signalRequired sensors/componentsRelated sensors/componentsVehicle speed sensor, Engine speed sensor
Frequency of operationContinuous
Duration20 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Battery voltage10.5 V±
Vehicle speed20 km/h (12.4 mph)±
Engine RPM1,000 rpm±
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Starter signalON (at ºmore than 20 km/h (12.4 mph) and more than 1,000 rpmº)
DID8D±01

A23548
ECM
E4
STAR ACCR
AM28
ED I18
Ignition SWB B
B±W 1C9
620
42 P
1
B±W
B 1
J2
J/C 1
17
B±O
2D
ALTE7 J38
1FGR
W4
ED2 IA1
S3 F10
Fusible
Link Block4
W±R
B±L
Battery 5B
ST 3A
1
StarterST Relay 5
B
12 3
Instrument Panel J/B
12
Engine Room J/B
2C
5 Sub J/B No. 4
P 3A 12A36
ACC CUT Relay
to Audio
J37J/C
C
GR
4 GR
N B±R
B±R
J/C BD
J51 J52B±R
STSW
E6 IG4B
Engine Room R/B No.2
2 B
2 2
2
2 2 B±RB±R RAD No.2
1C
1C
1C
1J 1J1J
1L
1E 3
5
W±L W±R
W±R
2C
2E1
3B±R
3
B1
B±W
W±B 6
A 1
2 3 58
3
J5
J/C 1
1W±B 128 B±R
W±RJ51 BE6 11
STA W±R
21
3
S2W±R4A
4B 19
9 Sub J/B No.4 GR
P1
Park/Neutral
Position SW
AM1ACC
AM2
ST2
ECU±B
SHORT PIN
B 7
B 2AM1
1
STA8
IA5
± DIAGNOSTICSENGINE
DI±299
493 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

DI±302
± DIAGNOSTICSENGINE
496 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0630 VIN not Programmed or Mismatch ECM/PCM
CIRCUIT DESCRIPTION
DTC P0630 is set when the Vehicle Identification Number (VIN) is not stored in the Engine Control Module
(ECM) or the input VIN is not accurate. Input the VIN with the hand±held tester.
DTC No.DTC Detecting ConditionTrouble Area
P0630
VIN is not stored in ECM.

Input VIN in ECM is not accurate.ECM
MONITOR STRATEGY
Related DTCsP0630VIN not programmed
Rid / tMain sensors/componentsECMRequired sensors/componentsRelated sensors/components±
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Battery voltage8 V±
Ignition switchON
StarterOFF
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
VIN codeNot programmed
COMPONENT OPERATING RANGE
ParameterStandard Value
VIN codeProgrammed
DID8E±01

DI±304
± DIAGNOSTICSENGINE
498 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P1340, P1341 Camshaft Position Sensor ºAº (Bank
Sensor 1)
CIRCUIT DESCRIPTION
Camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The camshaft drive gear (LH) has 3 teeth on its inner circumference. When the camshaft gear rotates, air
gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field
and result in change in the resistance of the MRE element.
The crankshaft signal plate has 32 teeth and is mounted on the crankshaft. The crankshaft position sensor
generates 32 signals at every engine revolution. The ECM detects the standard crankshaft angle based on
the G signal and the actual crankshaft angle and the engine speed by the NE signal.
DTC No.DTC Detecting ConditionTrouble Area
P1340
No camshaft position sensor signal to ECM during cranking
(2 trip detection logic)
Open or short in camshaft position sensor circuit

Camshaft position sensor
P1340
P1341No camshaft position sensor signal to ECM with engine speed
600 rpm or more

Camshaft osition sensor

LH camshaft timing pulley

ECM
MONITOR DESCRIPTION
The camshaft position sensor (G signal) consists of a magnet and MRE element.
The camshaft drive gear has 5 teeth on its inner circumference. When the camshaft gear rotates, air gap
changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and
result in change in the resistance of the MRE element. The crankshaft angle sensor plate has 32 teeth and
output 32 signals every engine revolution. The ECM detects the standard crankshaft angle based on the
G signal and actual crankshaft angle and engine speed by NE signal.
MONITOR STRATEGY
RltdDTC
P1340Camshaft position sensor (Bank 1) range check
or rationality
Related DTCs
P1341Camshaft position sensor (Bank 1) range check
or rationality
Rid / tMain sensors/componentsCamshaft position sensorRequired sensors/componentsRelated sensors/componentsCrankshaft position sensor, Engine speed sensor
Frequency of operationContinuous
Duration5 sec.
MIL operationP1340 case 1 (no signal): 2 driving cycles
P1340 case 2 (mis±aligned), P1341: Immediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
P1340 Case 1 (No signal):
StarterON
Minimum battery voltage while starter ON±11 V
DID8F±01

A23564
Engine Room J/B
EFI Relay
2
1EFI No.2
EFI No.1
3
5 2A2
J5
J/C A
EDW±B1
2F
Battery BF10
FL Block
4
5B
2D1
2H6E4 B±W
IA4
B±W8
MREL
14P±L L±B
E8 E8
2726
AIV2 AIV1 V14
VSV for Air Injection Control
(Bank 1)
V12
VSV for Air Injection Control
(Bank 2)
G±R G±R
G±R
G±R
IG422 J/C J16
BB G±R
IA44
G±R
AA J/C J2
G±RECM
± DIAGNOSTICSENGINE
DI±311
505 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

± DIAGNOSTICSENGINE
DI±317
511 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P1441Air switching valve No. 2 (Bank 1) is stuck open
Related DTCsP1444Air switching valve No. 2 (Bank 2) is stuck openRelated DTCs
P2440Air switching valve and air switching valve No. 2
are stuck open
Required sensors/componentsPressure sensor, Air switching valve No. 2 (Bank 1, 2), Electromagnetic air switching valve
Frequency of operationContinuous
Duration
P1441 (Air switching valve No. 2 (Bank 1) is stuck open): 20 sec.
P1444 (Air switching valve No. 2 (Bank 2) is stuck open): 20 sec.
P2440 (Air switching valve and air switching valve No. 2 are stuck open): 18 sec.
MIL operation
P1441 (Air switching valve No. 2 (Bank 1) is stuck open): 2 driving cycles
P1444 (Air switching valve No. 2 (Bank 2) is stuck open): 2 driving cycles
P2440 (Air switching valve and air switching valve No. 2 are stuck open):
1 driving cycle
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
P1441, P1444: Air switching valve No. 2 bank 1 and/or bank 2 are stuck open
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
CASE 1
Atmospheric pressure76 kPa (570 mmHg)±
Battery voltage11.5 V±
Time after secondary air injection out of
operation10 sec.±
AIR pumpOFF
Time after engine start10 sec.±
Air switching valve No. 2 (Bank 1)OFF
Air switching valve No. 2 (Bank 2)OFF
Air injection pressure sensor failNot detected
Air switching valveON
Engine RPM±3,750 rpm
CASE 2
Atmospheric pressure76 kPa (570 mmHg)±
Battery voltage11.5 V±
AIR pumpOFF
Time after engine start10 sec.±
Air switching valve No. 2 (Bank 1)OFF
Air switching valve No. 2 (Bank 2)OFF
Air injection pressure sensor failNot detected
Engine load0%±
Intake air amount40 g/sec±
IAT at engine start±15°C (5°F)±
ECT at engine start±5°C (41°F)

DI±318
± DIAGNOSTICSENGINE
512 Author: Date:
2005 SEQUOIA (RM1146U) Air switching valve
ON
Engine RPM±3,750 rpm
P2440: Electromagnetic air switching valve and air switching valve No. 2 are stuck open
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not presentSee page DI±18
Atmospheric pressure76 kPa (570 mmHg)±
Battery voltage11.5 V±
Time after secondary air injection out of
operation10 sec.±
Cumulative intake air amount172 g±
AIR pumpOFF
Air switching valveOFF
Air switching valve No. 2 (Bank 1)OFF
Air switching valve No. 2 (Bank 2)OFF
Engine RPM±3,750 rpm
Air injection pressure sensor failNot detected
TYPICAL MALFUNCTION THRESHOLDS
P1441, P1444: Air switching valve No. 2 bank 1 and/or bank 2 are stuck open
Detection CriteriaThreshold
CASE 1:
Both of the following conditions are metCondition (a) and (b)
(a) Cumulative pressure pulsation (When AI OFF)20 kPa (150 mmHg) or more
(b) Air pressure change (When ASV No.2 open)
(P1441 (Bank 1), P1444 (Bank 2))Less than 1 kPa (7.5 mmHg) or more
CASE 2:
Detected times of identifying condition 1 is met4 times or more
1. Cumulative pressure pulsation100 kPa (750 mmHg) or more
P2440: Electromagnetic air switching valve and air switching valve No. 2 are stuck open
Detection CriteriaThreshold
Detected times of identifying condition 1 is met4 times or more
1. Cumulative pressure pulsation100 kPa (750 mmHg) or more