lock TOYOTA SEQUOIA 2001 Service Manual PDF

A14809
B
BW
WB 2
EB2V2
VSV (ACIS)
2 1L±W21
E4ECM
ACIS
MREL 13
E3 P±B
B±R 1
1
1
1 1 1 1 1
12 EFI No. 2
EFI Main Relay
21
3
5
EFI No. 1
12
Engine Room No. 1 R/B
B±L
Battery B±W
W±B J3
J/C
AA
D
D
W±B
ECW
FL MAIN
1
1
4B
4A
FL BLOCK J7
J/C
W±B
1A DI±500
± DIAGNOSTICSENGINE
694 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

I08467
LOCKACC
ON
START
DI±508
± DIAGNOSTICSENGINE
702 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check ignition switch.
PREPARATION:
(a) Remove the lower finish panel.
(b) Disconnect the ignition switch connector.
CHECK:
Check resistance between terminals.
OK:
Standard:
Switch PositionTerminal ConditionSpecified Condition
LOCKAlways10 kW or more
ACC1 ± 3Below 1 W
ON1 ± 2 ± 3
5 ± 6Below 1 W
START1 ± 2
4 ± 5 ± 6Below 1 W
NG Replace ignition switch.
OK
Check for open in harness and connector be-
tween ECM and ignition switch, ignition
switch and battery (See page IN±35).

DI±518
± DIAGNOSTICSAUTOMATIC TRANSMISSION
712 Author: Date:
2005 SEQUOIA (RM1146U) Output speed sensor
Output shaft speed sensor
Input speed sensor, Input turbine speed sensor ºAº, Speed
sensor (NT), Turbine speed sensorInput turbine speed sensor
PNP switch, NSWPark/neutral position switch
Pressure control solenoidTransmission pressure control solenoid
Shift solenoidTransmission shift solenoid valve
Transmission control switch, Shift lock control unitShift lock control module
Engine immobilizer system, Immobilizer systemVehicle anti±theft system

DIDIO±01
/ /
How Often Does
Problem Occur?/ /
Automatic Transmission
System Check SheetInspector 's
Name :
Customer 's Name
Date Vehicle
Brought In/ /Odometer Readingkm
mile
Date Problem
Occurred
ContinuousIntermittent ( times a day)
SymptomsNo up±shift ( 1st " 2nd 2nd " 3rd 3rd " 4th 4th " 5th)
Vehicle does not move ( Any position Particular position)
No down±shift ( 5th " 4th 4th " 3rd 3rd " 2nd 2nd " 1st)
Lock±up malfunction
Shift point too high or too low
Harsh engagement ( N " D Lock±up Any drive position)
Slip or shudder
No kick±down
Others
DTC Check1st Time
2nd Time Check Item
Normal system codeTrouble code (DTC )
Normal system codeTrouble code (DTC )
Malfunction
Indicator LampNormal
Remains ON
VIN
Production Date
Licence Plate No.
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±523
717 Author: Date:
2005 SEQUOIA (RM1146U)
CUSTOMER PROBLEM ANALYSIS CHECK

DIDIQ±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±535
729 Author: Date:
2005 SEQUOIA (RM1146U)
ROAD TEST
1. PROBLEM SYMPTOM CONFIRMATION
Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that
the transaxle does not shift up, shift down, or the shift point is too high or too low, conduct the following road
test referring to the automatic shift schedule and simulate the problem symptoms.
2. ROAD TEST
NOTICE:
Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C
(122 to 176°F).
(a) D position test:
Shift into the D position and fully depress the accelerator pedal and check the following points. Check
up±shift operation.
(1) Check up±shift operation.
Check that 1 " 2, 2 " 3, 3 " 4 and 4 " 5th up±shifts take place, and that the shift points conform
to the automatic shift schedule (See page SS±24).
HINT:
5th Gear Up±shift Prohibition Control

Engine coolant temperature is 55 °C (131 °F) or less and vehicle speed is at 51 km/h (32 mph) or less.
4th Gear Up±shift Prohibition Control

Engine coolant temperature is 40 °C (104 °F) or less and vehicle speed is at 45 km/h (28 mph) or less.
5th Gear Lock±up Prohibition Control

Brake pedal is depressed.

Accelerator pedal is released.

Engine coolant temperature is 60 °C (140 °F) or less.
(2) Check for shift shock and slip.
Check for shock and slip at the 1 " 2, 2 " 3, 3 " 4 and 4 " 5th up±shifts.
(3) Check for abnormal noise and vibration.
Check for abnormal noise and vibration when up±shifting from 1 " 2, 2 " 3, 3 " 4 and 4 " 5
while driving with the shift lever in the D position, and check while driving in the lock±up condition.
HINT:
The check for the cause of abnormal noise and vibration must be done thoroughly as it could also be due
to loss of balance in the differential, torque converter clutch, etc.
(4) Check kick±down operation.
Check vehicle speeds when the 2nd to 1st, 3rd to 2nd, 4th to 3rd, and 5th to 4th kick±downs take
place while driving with the shift lever in the D position. Confirm that each speed is within the
applicable vehicle speed range indicated in the automatic shift schedule (See page SS±24).
(5) Check abnormal shock and slip at kick±down.
(6) Check the lock±up mechanism.

Drive in the D position (5th gear), at a steady speed (lock±up ON).

Lightly depress the accelerator pedal and check that the engine speed does not change
abruptly.
HINT:
If there is a big jump in engine speed, there is no lock±up.

DI±536
± DIAGNOSTICSAUTOMATIC TRANSMISSION
730 Author: Date:
2005 SEQUOIA (RM1146U)
(b) 4 (O/D OFF) position test:
Shift into the 4 (O/D OFF) position and fully depress the accelerator pedal and check the following
points.
(1) Check up±shift operation.
Check that the 1 " 2, 2 " 3 and 3 " 4 up±shifts take place and that the shift point conforms
to the automatic shift schedule (See page SS±24).
HINT:

There is no 5th up±shift in the 4 position.

4th Gear Lock±up Prohibition Control

Brake pedal is depressed.

Accelerator pedal is released.

Engine coolant temperature is 60 °C (140 °F) or less.
(2) Check engine braking.
While driving in the 4 position and 4th gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.
(4) Check the lock±up mechanism.

Drive in 4 position 4th gear, at a steady speed (lock±up ON).

Lightly depress the accelerator pedal and check that the engine speed does not change
abruptly.
HINT:
If there is a big jump in engine speed, there is no lock±up.
(c) 3 position test:
Shift into the 3 position and fully depress the accelerator pedal and check the following points.
(1) Check up±shift operation.
Check that the 1 " 2 and 2 " 3 up±shifts takes place and that the shift point conforms to the
automatic shift schedule (See page SS±24).
HINT:

There is no 4th up±shift and lock±up in the 3 position.

When the 2nd start switch is ON, there is no 1 "2 up±shift and 2 "1 down±shift.
(2) Check engine braking.
While running in the 3 position and 3rd gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.
(d) 2 position test:
Shift into the 2 position and fully depress the accelerator pedal and check the following points.
(1) Check up±shift operation.
Check that the 1 " 2 up±shift takes place and that the shift point conforms to the automatic shift
schedule (See page SS±24).
HINT:

There is no 3rd up±shift and lock±up in the 2 position.

When the 2nd start switch is ON, there is no 1 "2 up±shift and 2 "1 down±shift.

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±537
731 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Check engine braking.
While running in the 2 position and 2nd gear, release the accelerator pedal and check the engine
braking effect.
(3) Check for abnormal noises during acceleration and deceleration, and for shock at up±shift and
down±shift.
(e) L position test:
Shift into the L position and fully depress the accelerator pedal and check the following points.
(1) Check no up±shift.
While running in the L position, check that there is no up±shift to 2nd gear.
(2) Check engine braking.
While running in the L position, release the accelerator pedal and check the engine braking ef-
fect.
(3) Check for abnormal noises during acceleration and deceleration.
(f) R position test:
Shift into the R position, lightly depress the accelerator pedal, and check that the vehicle moves back-
ward without any abnormal noise or vibration.
CAUTION:
Before conducting this test, ensure that the test area is free from people and obstruction.
(g) P position test:
Stop the vehicle on a grade (more than 5°) and after shifting into the P position, release the parking
brake. Then, check that the parking lock pawl holds the vehicle in place.

DIDIW±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±551
745 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DRIVE PATTERN
1. MONITOR DRIVE PATTERN FOR ECT TEST
(a) Perform this drive pattern as one method to simulate the detection conditions of the ECT malfunctions.
(The DTCs may not be detected due to the actual driving conditions. And some codes may not be de-
tected through this drive pattern.)
HINT:
Preparation for driving

Warm up the engine sufficiently. (Engine coolant temperature is 60 °C (140 °F) or higher).

Drive the vehicle when the atmospheric temperature is ±10 °C (14 °F) or higher. (Malfunction is not
detected when the atmospheric temperature is ±10 °C (14 °F) or less).
Notice in driving

Drive the vehicle through all gears.
Stop " 1st " 2nd " 3rd " 4th " 5th " 5th (lock±up ON).

Repeat the above driving pattern three times or more.
NOTICE:

The monitor status can be checked using the OBD II scan tool. When using the hand±held tes-
ter, monitor status can be found in the ºENHANCED OBD II / DATA LISTº or under ºCARB OBD
IIº.

In the event that the drive pattern must be interrupted (possibly due to traffic conditions or other
factors), the drive pattern can be resumed and, in most cases, the monitor can be completed.

Perform this drive pattern on a level road as much as possible and strictly observe the posted
speed limits and traffic laws while driving.

D14144
Warmed up
sufficiently
Approx.100 km/h
(62 mph)
Vehicle Speed
Approx. 80 km/h
(50 mph)
0
Normal acceleration
through all the gears from 1st to 5th
Lock±up ON
Vehicle Speed
Stop
(Idling)
Maintain a constant speed or gradual acceleration (with the throttle open)
for 3 minutes or more.
*1 DI±552
± DIAGNOSTICSAUTOMATIC TRANSMISSION
746 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:
*1: Drive at such a speed in the uppermost gear, to engage lock±up. The vehicle can be driven at a speed
lower than that in the above diagram under the lock±up condition.
NOTICE:
It is necessary to drive the vehicle for approximately 30 minutes to detect DTC P0711 (ATF tempera-
ture sensor malfunction).

DIDIX±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±553
747 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
If a normal code is displayed during the diagnostic trouble code check although the trouble still occurs, check
the electrical circuits for each symptom in the order given in the charts on the following pages and proceed
to the page given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
1. Chapter 1: Electronic Circuit Matrix Chart
Refer to the table below when the trouble cause is considered to be electrical.
If the instruction ºProceed to next circuit inspection shown on matrix chartº is given in the flow chart
of each circuit, proceed to the circuit with the next highest number in the table to continue the check.
If the trouble still occurs even though there are no abnormalities in any of the other circuits, check and
replace the ECM.
HINT:
*1: When the circuit on which mark *1 is attached is defective, DTC could be output (see page DI±573).
SymptomSuspect AreaSee page
No up±shift
(A particular gear, from 1st to 4th gear, is not up±shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±641
DI±646
IN±35
No up±shift (4th " 5th)
1. O/D main switch circuit
2. Engine coolant temp. sensor circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SL1) circuit *1
5. Shift solenoid valve (SL2) circuit *1
6. Shift solenoid valve (SR) circuit *1
7. ECM
DI±688
DI±58
DI±591
DI±603
DI±631
DI±651
IN±35
No up±shift (3rd " 4th)
1. Engine coolant temp. sensor circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±58
DI±646
IN±35
No up±shift (1st " 2nd)
1. Shift position L switch circuit
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±691
DI±646
IN±35
No down±shift (5th " 4th)
1. O/D main switch circuit
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SL2) circuit *1
4. Shift solenoid valve (SR) circuit *1
5. ECM
DI±688
DI±603
DI±631
DI±651
IN±35
No down±shift (2nd " 1st)
1. Shift position L switch circuit
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±691
DI±646
IN±35
No down±shift
(A particular gear, from 1st to 4th gear, is not down±shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI±641
DI±646
IN±35
No lock±up
1. ATF temperature sensor circuit *1
2. Stop light switch circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SLU) circuit *1
5. Engine coolant temp. sensor circuit *1
6. ECM
DI±582
DI±600
DI±591
DI±680
DI±58
IN±35
No lock±up off4. Shift solenoid valve (SLU) circuit *1
6. ECM
DI±680
IN±35