engine TOYOTA SEQUOIA 2001 Service Repair Manual

I28471
Combination MeterMemory Seat ECU
& SW
Sub J/B No. 3J/C
J24
J/C
Instrument Panel J/B
F10
Fusible Link BlockI18
Ignition SW
Engine Room J/B
Battery
BHJ24
J/C J/C
J/C C5 J33 BI2 M6J34
J31 J32
3A 3AJ33 J34
J33 J34BI2
BI2 BI2
M6
M6 M7
AM1 ECU±IG
1F
1L
1J 1E 1G1C
1 4
6
1 16
2
1C
2 4
PWR SEAT
1 2
M7 BI2 ECU±B
Short Pin
2D 2C18 ALT
IG1 AM1 12
BB
W±B
W±B W±B
B58W W±L
W±R W±RB±Y B±R
L±O
3 W±R
W±RW±R W±R B±R B±R B±R L±O
L±O L±O L±O
3 111 8151641
5
A 9 C
A GG A
WWW17 30
CL
I FMPX1
+B
IG
SYSB
GND 1 4
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
DI±1947
2141 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

I28473
Combination Meter
F18
Front Passenger
Door ECUBack Door ECU
Sub J/B No. 3I18
Ignition SW Instrument Panel J/B
F10
Fusible Link Block
Engine Room J/BInstrument Panel J/B
Sub J/B No. 3
Battery
BJJ19
J/CJ22
J/C J37
J/CJ/C
J/C J33 J34
J33 J34 C5B11 BF1 BD2
II2B11
B11
B11 BF1 BD2
BD2 BF1 IN1
AM1 ECU±IG
1F
1L
1G1C
14
6
12
1C
154
12PWR No. 5 ALT
58
43C 3A88AAGAB H
IG1
AM1
1 26 7 312
1
6
4 2
5 11 1114 8
BB B B B
20 (*1)LG±R
B±RLG±R LG±R LG±R
B±RB±R B±R B±R
B±R B±Y
W±L W
B B
L±W L±W L±W L±W
W±R
W±R W±R
W±R W±R W±R
W±B W±B W±B W±B
A212
BB3 5
B11
B11 10 12 11 2
3A 3C
BD2 BF1
BF1 BD1IN1BF1 BD1 IC4
2 3 8 1
1J
1E 2C 2DECU±B
Short Pin
23
10MPX1
SIG
BDR
GND MPX2
BECU MPX1
*1: w/ Driving Position Memory
*2: w/o Driving Position Memory 10 (*2)
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
DI±1953
2147 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

DID9K±01
I27726
Radio Receiver Assy
Rear Door Speaker Tweeter
Rear Door Speaker Front Door Speaker (*1)
Front Door Speaker and
Woofer (*2)Steering Pad
Switch
Instrument Panel J/B

RAD NO. 2 Fuse

ECU±B Fuse

AM1 FuseEngine Room J/B

RAD NO. 1 Fuse

RAD NO. 3 Fuse
Ignition Switch
Disc Player
Controller
(*3)
Stereo
Component
AmplifierMulti±display
Controller (*3)
VTR
Terminal
(*3)Headphone
Terminal
(*3, *4)
Television Display Assy (*3)
Rear Seat Audio
Controller Assy (*4)
Radio Sub
Antenna*1: Built±in Type Amplifier
*2: Separate Type Amplifier
*3: w/ RSE System
*4: w/ RSA System Radio Main Antenna
DI±1956
± DIAGNOSTICSAUDIO SYSTEM
2150 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DI±1966
± DIAGNOSTICSAUDIO SYSTEM
2160 Author: Date:
2005 SEQUOIA (RM1146U)
5. Identify the condition in which the noise occurs, and check the noise filter on the related part.
Condition in which noise occursNoise Source
Depressing the acceleration pedal increases the noise, and stopping the
engine stops the noise immediately.Generator
Noise occurs during A/C or the heater operation.Blower motor
Rapid acceleration while driving on an unpaved road or after the ignition
switch is turned on makes noise.Fuel pump
Pressing and then releasing the horn switch, and keeping pressing the horn
switch makes unusual noise.Horn
Quiet noise is heard while the engine is running, but stops with the engine.Ignition
Noise occurs synchronously with the turn signal flash.Flasher
Noise occurs during window washer operation.Washer
Noise occurs while the engine is running, and it continues even after the en-
gine stops.Engine coolant temperature sensor
Noise occurs during wiper operation.Wiper
Noise occurs when the brake pedal is depressed.Stop light switch
Others.Static electricity stored on the vehicle
Reference:

Make sure first that there is no noise from outside. Failing to do so makes the noise source detec-
tion difficult and leads to misdiagnosis.

The noise should be removed in descending order of loudness.

Tuning the radio so that no station is received wakes the noise more noticeable, making the rec-
ognition of the phenomenon easier.

DID9T±01
± DIAGNOSTICSAUDIO SYSTEM
DI±1979
2173 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
TermsMeaning
Physical addressThree±digit code (shown in hexadecimal) which is given to each component com-
prising the AVC±LAN.
Corresponding to the function, individual symbols are specified.
Logical addressTwo±digit code (shown in hexadecimal) which is given to each function comprising
the inner system of the AVC±LAN.
HINT:
Titles for each unit are stated in the following order: parts name (physical address) and [Name indicated on
the DTC display]
1. Radio receiver assy (physical address: 190) [AUDIO H/U]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D6
*1Absence of Master
Component in which this code is recorded was
disconnected from system or master component
with ignition switch in ACC or ON.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
D8
*2
*5No Response to Connection
CheckComponent shown by sub code is or was discon-
nected from system after engine start.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±

± DIAGNOSTICSAUDIO SYSTEM
DI±1981
2175 Author: Date:
2005 SEQUOIA (RM1146U)DB
*1
Mode Status ErrorDual alarm is detected.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
DC
*3Transmission Error
Transmission to component shown by auxiliary
code has been failed.
(Detecting this DTC does not necessarily mean
actual failure.)
1. Power source circuit (Rear seat
audio controller). *6
2. Power source circuit (Multi±dis-
play controller sub±assy) *7
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
6. Replace stereo component am-
plifier assy.
7. Replace rear seat audio control-
ler. *6
8. Replace multi±display controller
sub±assy. *7DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
DD
*4Master Reset (Momentary Inter-
ruption)After the engine was started, master component
was disconnected from system.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±

DI±1982
± DIAGNOSTICSAUDIO SYSTEM
2176 Author: Date:
2005 SEQUOIA (RM1146U)DE
*4
Slave Reset (Momentary Inter-
ruption)After the engine was started, component shown
by sub code was disconnected from system.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
DF
*4Master Error
Due to defective cognition of component with a
display, master function is switched to audio
equipment.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: If the power connector is disconnected after the engine starts, this code is recorded after 180 se-
conds.

*3: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*4: This code may be stored if the ignition key is held in the START position for 1 minute or more before
returning to the ON position.

*5: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*6: w/ Rear seat audio system only.

*7: w/ Rear seat entertainment system only.

± DIAGNOSTICSAUDIO SYSTEM
DI±1983
2177 Author: Date:
2005 SEQUOIA (RM1146U)
Logical address: 01 (Communication control) continued
DTCNameDiagnosisVerificationSee page
E0
*1Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E2ON/OFF Instruction Parameter
ErrorError occurs in ON/OFF controlling command
from master component.Replace radio receiver assy.±
E3
*1Registration Request Transmis-
sion
Registration Request command is output from
component shown by sub code.
Receiving Connection Check Instruction, Regis-
tration Request command is output from sub±
master component.
Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.
(b) Logical address: 61 (Cassette switch)
DTCNameDiagnosisVerificationSee page
40Mechanical Error of MediaMalfunction due to mechanical failure is identified.
Either that, or cassette tape is cut or entangled.1. Inspect cassette tape.
2. Replace radio receiver assy.±
±
(c) Logical address: 62 (CD player)
DTCNameDiagnosisVerificationSee page
42No Disc ReadoutDisc cannot be read.1. Inspect CD.
2. Replace radio receiver assy.±
±
44CD player ErrorError is detected in CD player.Replace radio receiver assy.±
47Detection of high temperatureHigh temperature is detected in CD player.
With ignition switch off, leave ve-
hicle in cool shaded place for a
while and recheck. After deleting
the DTC memory, if same code de-
tected, replace radio receiver assy.
±
48Detection of excess currentOver current is present in CD player.Replace radio receiver assy.±
(d) Logical address: 63 (In±dash CD changer)
DTCNameDiagnosisVerificationSee page
42No Disc ReadoutDisc cannot be read.1. Inspect CD.
2. Replace radio receiver assy.±
±
44CD player ErrorError is detected in CDDH.Replace radio receiver assy.±
47Detection of high temperatureHigh temperature is detected in CDCH.
With ignition switch off, leave ve-
hicle in cool shaded place for a
while and recheck. After deleting
the DTC memory, if same code de-
tected, replace radio receiver assy.
±
48Detection of excess currentOver current is present in CDCH.Replace radio receiver assy.±

DI±1984
± DIAGNOSTICSAUDIO SYSTEM
2178 Author: Date:
2005 SEQUOIA (RM1146U)
2. Stereo component amplifier assy (physical address: 440) [DSP±AMP]
Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D6
*1Absence of Master
Component in which this code is recorded was
disconnected from system with ignition in ACC or
ON. Either that, or radio receiver assy was dis-
connected when this code was recorded.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±
D7Communication Check Error
Component in which this code is recorded is or
was disconnected from system after engine start.
Either that, or radio receiver assy was discon-
nected when this code was recorded.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±
DC
*2Transmission Error
Transmission to component shown by auxiliary
code failed.
(Detecting this DTC does not necessarily mean
actual failure.)If same auxiliary code is recorded in
other components, check harness
for power supply and communica-
tion system of all components
shown by code.
±
DD
*3Master Reset (Momentary Inter-
ruption)After engine was started, radio receiver assy was
disconnected from system.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±

± DIAGNOSTICSAUDIO SYSTEM
DI±1985
2179 Author: Date:
2005 SEQUOIA (RM1146U)
Logical address: 01 (Communication control) continued
DTCNameDiagnosisVerificationSee page
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±
E0
*1Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E1
*1Audio processor ON errorWhile source equipment is operating, AMP output
stops.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±
E2ON/OFF Instruction Parameter
ErrorError occurs in ON/OFF controlling command
from radio receiver assy.Replace radio receiver assy.±
E3
*1Registration Request Transmis-
sionRegistration Request command is output from
slave component.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*3: This code may be stored if the ignition key is held in the START position for one minute or more
before returning to the ON position.

*4: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*5: w/ Rear seat audio system only.

*6: w/ Rear seat entertainment system only.