sensor TOYOTA SEQUOIA 2001 Service Repair Manual

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1609
1803 Author: Date:
2005 SEQUOIA (RM1146U)A/T R
Receives an R signal from the park/neutral position switch (Direct line)±
TAIL/HEADReceives a dimmer signal from the body ECU (BEAN)±
TIRE PRESSUREReceives a low tire pressure signal from the tire pressure monitor ECU (Direct line)
4LOReceives a 4LO signal from the 4WD control ECU (Direct line)±
MAIN REQD (Blinks)Blinks when 4,500 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
MAIN REQD (Comes on)Blinks when 5,000 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
RSCA OFFReceives an RSCA OFF signal from the airbag sensor center (Direct line)
HIReceives a suspension position HI signal from the suspension control ECU (Direct
line)
NReceives a suspension position N signal from the suspension control ECU (Direct
line)
LOReceives a suspension position LO signal from the suspension control ECU (Direct
line)
AHC MAN.Receives a suspension control manual signal from the suspension control ECU
(Direct line)
*1: w/ Day time running light
*2: w/o Day time running light
BUZZER:
ItemDetail
Key ReminderBuzzer is ON: Ignition switch is OFF, key is inserted, and door is open.
Fasten BeltBuzzer is ON: Ignition switch is ON and seat belt is unfastened.
2. COMBINATION METER IN SEQUOIA HAS THE FOLLOWING FEATURES:
(a) Built±in buzzer for the reminder system (key and seat belt)
(b) Integrated trip and odometer knobs

Press and release knob to scroll through trip ºAº, trip ºBº, and odometer features.

Press and hold the trip knob to reset trip meter functions.
(c) Oil maintenance indicator

When 4,500 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor begins to blink for 15 seconds after the ignition switch is turned to the ON position.

When 5,000 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor comes on.

Press and hold the trip knob to reset the oil maintenance indicator.
(d) Rotate knob to adjust interior illumination

DID8U±01
DI±1614
± DIAGNOSTICSCOMBINATION METER SYSTEM
1808 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
Inspect the related ºFuseº and ºRelayº before confirming the suspected area as shown in the table below.
MALFUNCTION SYSTEM:
SymptomSuspected AreaSee page
Entire combination meter does not operate.Refer to troubleshooting proceduresDI±1628
Operating light control rheostat does not change light brightness.Refer to troubleshooting proceduresDI±1645
Seat belt warning does not operate.Refer to troubleshooting proceduresDI±1650
Key reminder warning buzzer does not sound.
1. Multiplex communication system
2. Key unlock warning switch circuit
3. Door courtesy lamp switch circuit
4. Combination meter assyDI±1892
DI±1715
DI±1728
IN±35
METER GAUGES:
SymptomSuspected AreaSee page
Malfunction in speedometerRefer to troubleshooting proceduresDI±1632
Malfunction in tachometerRefer to troubleshooting proceduresDI±1636
Malfunction in fuel receiver gaugeRefer to troubleshooting proceduresDI±1640
Malfunction in engine coolant temperature receiver gaugeRefer to troubleshooting proceduresDI±1644
Malfunction in oil pressure receiver gaugeRefer to troubleshooting proceduresDI±1654
Malfunction in volt meterRefer to troubleshooting proceduresDI±1658
WARNING LIGHTS:
SymptomSuspected AreaSee page
Check engine warning light (MIL) does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Discharge warning light does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Brake warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
ABS warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
SRS warning light does not come on.
1. Airbag sensor assy
2. Wire harness or connector
3. Combination meter assyDI±1126
±
IN±35
Open door warning light does not come on.
1. Door courtesy light switch circuit
2. Wire harness or connector
3. Combination meter assy
4. Body ECUDI±1728
±
IN±35
IN±35
Fuel level warning light does not come on.
1. Refer to troubleshooting
2. Wire harness or connector
3. Combination meter assyDI±1640
±
IN±35
Low oil pressure warning light does not come on.
1. Low oil pressure warning switch
2. Wire harness or connector
3. Combination meter assyBE±55
±
IN±35

Wire harness side
1
2
3
4
5
6
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
401
2
3
4
5
8 6
10
11
12
13
14
15
16
17
18
19
21
23
24
Terminal No.
Translate ECU
ECM
STA Fuse
Front Seat Inner Belt LH (Buckle Switch)
Overhead Module (Garage Door Opener)
Overhead Module (Garage Door Opener)
Washer Level Sensor
ECM
ECM (*1)
Transponder Key Computer
Body ECU
ECM
ECM
Tire Pressure Monitor ECU
Injector No. 1
Light Control Rheostat
ECM
Speed Sensor
4P OUT (Other Parts)
Fuel Sender Gauge
Oil Pressure Sender Gauge
IGN Fuse
Airbag Sensor Assembly
Memory Seat ECU and SW (*2)
Back Door ECU
Integration Control and Panel
Turn Signal Flasher Relay
Park/Neutral Position Switch
Airbag Sensor AssemblyTranslate ECU
Translate ECU
Skid Control ECU
4WD Control ECU
Alternator
Speed Sensor
Fuel Sender Gauge
Ground
Suspension Control ECU
Body ECU (*4)
Body ECU (*3)
Turn Signal Flasher Relay
Skid Control ECU
ECU±B Fuse
IGN1 Fuse Connectors:
Terminal No.
Wire harness side
C5
C64WD Control ECU
4WD Control ECU
Suspension Control ECU
Suspension Control ECU
Suspension Control ECU
*1: 4WD
*2: w/ Driving Position Memory
*3: w/ Daytime Running Light
*4: w/o Daytime Running LightPark/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch DI±1624
± DIAGNOSTICSCOMBINATION METER SYSTEM
1818 Author: Date:
2005 SEQUOIA (RM1146U)

DID8X±01
DI±1626
± DIAGNOSTICSCOMBINATION METER SYSTEM
1820 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
DATA LIST
According to the DATA LIST displayed by the hand±held tester, you can read the values of the switches,
sensors, actuators and so on without part removal. Reading the DATA LIST as the first step of troubleshoot-
ing is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
SPEED METER
Vehicle Speed Meter /
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Almost the same as actual vehicle
speed (When driving)
TACHO METEREngine RPM /
Min.: 0 rpm Max.: 12,750 rpmAlmost the same as actual engine
speed (When engine is running)
FUEL GAUGEFuel Input /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the fuel receiver gauge
angle.

LIGHT RHEOSTATLight Control Rheostat /
Min.: 0 Max.: 255Light control rheostat switch is
Dark (0) " Bright (255)
OIL GAUGEOil Gauge /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the oil pressure receiver
gauge angle.

ODO/TRIP SWODO / TRIP
ODO/TRIP switch / ON/OFFON: Switch is pushed
OFF: Switch is released

I28558
C612
W±B
Battery AW
58BR
IECombination Meter
W±L I18
Ignition SW
2 1
AM1 IG1
B±Y
W Instrument Panel J/B
AM1
21 47
6 1 6
9 1C
1C
1D 1E
1L
1FR±L
R±LSub J/B No. 3
3B 3A515C524
C610 R±L
Y±RY
Y±RY
13
23 19
26
IG4
IG4
IG4
GAUGE
B V1
Vehicle Speed Sensor
(Combination Meter)
F10
Fusible Link Block
J8
J/C DI±1632
± DIAGNOSTICSCOMBINATION METER SYSTEM
1826 Author: Date:
2005 SEQUOIA (RM1146U)
Malfunction in speedometer
CIRCUIT DESCRIPTION
The speedometer detects vehicle speed based on a 4±pulse signal from the vehicle speed sensor.
WIRING DIAGRAM
DID8Z±01

N02332
1
2 3
DI±1634
± DIAGNOSTICSCOMBINATION METER SYSTEM
1828 Author: Date:
2005 SEQUOIA (RM1146U)
3 Inspect vehicle speed sensor.
PREPARATION:
(a) Disconnect the vehicle speed sensor connector.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative (±) lead to terminal 2.
(c) Connect the positive (+) lead from the tester to terminal
3 and the negative (±) lead to terminal 2.
(d) Rotate the shaft.
CHECK:
Check that voltage between terminals 2 and 3 changes from
approx. 0 V to16 V or more.
OK:
Voltage changes from approx. 0 V to 16 V
HINT:
The voltage should change 4 times for every revolution of the
speed sensor shaft.
NG Replace vehicle speed sensor.
OK

I28569
Combination Meter:
C5±24
I28570
Combination Meter:
C6±12
C6±10
I28573
Vehicle Speed Sensor
Wire Harness Side:
V1
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1635
1829 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check harness and connector (Vehicle speed sensor ± combination meter and
vehicle speed sensor ± battery).
PREPARATION:
Disconnect the combination meter connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester connectionConditionSpecified condition
C5±24 ± V1±3AlwaysBelow 1 W
C6±10 ± V1±2AlwaysBelow 1 W
C6±12 ± Body groundAlwaysBelow 1 W
C5±24 ± Body groundAlways10 kW or higher
C6±10 ± Body groundAlways10 kW or higher
CHECK:
Measure the voltage according to the value(s) in the table be-
low.
OK:
Tester connectionConditionSpecified condition
V1±1 ± Body groundIgnition switch OFFBelow 1 V
V1±1 ± Body groundIgnition switch ON10 to 14 V
NG Repair or replace harness or connector.
OK
Replace combination meter
(See page IN±35).

I28559
E5 C5 ECU
TACHCombination Meter
23 J/C
J14D
J15F
Y±G Y±G 1 DI±1636
± DIAGNOSTICSCOMBINATION METER SYSTEM
1830 Author: Date:
2005 SEQUOIA (RM1146U)
Malfunction in tachometer
CIRCUIT DESCRIPTION
The indication on the tachometer is based on information that the ECM receives from the crankshaft position
sensor.
WIRING DIAGRAM
DID90±01

DI±1644
± DIAGNOSTICSCOMBINATION METER SYSTEM
1838 Author: Date:
2005 SEQUOIA (RM1146U)
Malfunction in engine coolant temperature receiver gauge
CIRCUIT DESCRIPTION
The ECM receives an engine coolant temperature signal from the engine coolant temperature sensor and
sends it to the A/C ECU.
The combination meter receives the signal from the A/C ECU through multiplex communication. Therefore,
if a malfunction occurs in the engine coolant temperature receiver gauge, there may be a malfunction in the
multiplex communication system, air conditioning system, or engine system.
(Multiplex communication system: See page DI±1892)
(Air conditioning system: See page DI±2301)
(Engine system: See page DI±9)
INSPECTION PROCEDURE
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
COOLANT TEMPHIGH / NORMAL / LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
OK:
Engine coolant temperature receiver gauge readings change according to hand±held tester op-
eration.
OK Go to engine system or air conditioning system
(See page DI±9 or DI±2301).
NG
Replace combination meter
(See page IN±35).
DID92±01

DID4Z±01
DI±1666
± DIAGNOSTICSSLIDING ROOF SYSTEM
1860 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the hand±held tester, you can read the value of the switch, sensor,
actuator and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting is one
of the method to shorten the labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, read the ºDATA LISTº.
SLIDE ROOF:
ItemMeasurement Item/
Display (Range)Normal conditionDiagnostic Note
LIMIT SW 1Position SW NO.1/
ON or OFFON: 250 mm point from fully opened position
OFF: Sliding roof fully closed position±
LIMIT SW 2Position SW NO.2/
ON or OFFON: Sliding roof fully closed position
OFF: Sliding roof except fully closed position±
OPEN SWSliding roof open SW
signal/ON or OFFON: Sliding roof is open
OFF: Sliding roof is close±
CLOSE SWSliding roof close SW
signal/ON or OFFON: Sliding roof is close
OFF: Sliding roof is open±
UP SWSliding roof up SW sig-
nal/ON or OFFON: Sliding roof is up
OFF: Sliding roof is down±
DOWN SWSliding roof down SW
signal/ON or OFFON: Sliding roof is down
OFF: Sliding roof is up±
IG (DIRCT)Ignition SW (Direct
signal)/ON or OFFON: Ignition switch to on
OFF: Ignition switch to off±
IG (MPX)Ignition SW (MPX)/ON
or OFFON: Ignition switch to on
OFF: Ignition switch to off±
2. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one of the meth-
od to shorten the labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, perform the ºACTIVE TESTº.
SLIDE ROOF:
ItemTest DetailsDiagnostic Note
SLIDE ROOFSliding roof CLOS/UP ± OPN/DWNDuring this ACTIVE TEST, jam protection caught
detection can be monitored.