engine oil TOYOTA SEQUOIA 2001 Service Repair Manual

B04770
IN±18
± INTRODUCTIONFOR ALL OF VEHICLES
18 Author: Date:
2005 SEQUOIA (RM1146U)
(4) Check that the VSC TRAC warning light blinks.
(5) After the measurement, remove the SST and re-
start the engine. At this time, make sure that the
VSC TRAC warning light is off.
(b) Notice in VSC operation.
(1) Removal and reinstallation of VSC±related compo-
nents may cause misadjustment of them. Do not re-
move or reinstall them unless necessary.
(2) When conducting VSC±related operations, do not
fail to make sure that the preparation and the finish-
ing of the operation are all performed in accordance
with the direction in this text.
3. FOR VEHICLES EQUIPPED WITH A CATALYTIC CONVERTER
CAUTION:
If a large amount of unburned gasoline flows into the converter, it may overheat and create a fire haz-
ard. To prevent this, observe the following precautions and explain them to your customer.
(a) Use only unleaded gasoline.
(b) Avoid prolonged idling.
Avoid running the engine at idle speed for more than 20 minutes.
(c) Avoid spark jump test.
(1) Perform spark jump test only when absolutely necessary. Perform this test as rapidly as possible.
(2) While testing, never race the engine.
(d) Avoid prolonged engine compression measurement.
Engine compression tests must be done as rapidly as possible.
(e) Do not run engine when fuel tank is nearly empty.
This may cause the engine to misfire and create an extra load on the converter.
(f) Avoid coasting with ignition turned off.
(g) Do not dispose of used catalyst along with parts contaminated with gasoline or oil.
4. IF VEHICLE IS EQUIPPED WITH MOBILE COMMUNICATION SYSTEM
For vehicles with mobile communication systems such as two±way radios and cellular telephones, observe
the following precautions.
(1) Install the antenna as far as possible away from the ECU and sensors of the vehicle's electronic
system.
(2) Install the antenna feeder at least 20 cm (7.87 in.) away from the ECU and sensors of the ve-
hicle's electronic systems. For details about ECU and sensor locations, refer to the section on
the applicable component.
(3) Do not wind the antenna feeder together with the other wiring as much as possible, also avoid
running the antenna feeder parallel with other wire harness.
(4) Check that the antenna and feeder are correctly adjusted.
(5) Do not install powerful mobile communication system.

MA001±42
± MAINTENANCEOUTSIDE VEHICLE
MA±1
48 Author: Date:
2005 SEQUOIA (RM1146U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing.
If necessary, tighten them.
4. TIRE ROTATION (See page SA±3)
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, find the cause and correct.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

MA003±50
MA±4
± MAINTENANCEUNDER HOOD
51 Author: Date:
2005 SEQUOIA (RM1146U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see±through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(2UZ±FE engine: See page CO±14)
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see±through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re±insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 ± 80°C, 158 ± 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, find the cause and
correct.

MA004±18
P08488
Back Front
± MAINTENANCEENGINE
MA±5
52 Author: Date:
2005 SEQUOIA (RM1146U)
ENGINE
INSPECTION
HINT:
Perform the following procedures when the engine is cold.
1. REPLACE TIMING BELT
(See page EM±13)
2. INSPECT DRIVE BELT
(See page CH±1)
3. REPLACE SPARK PLUGS
(See page IG±1)
4. INSPECT AIR FILTER
(a) Visually check that the air cleaner element is not exces-
sively dirty, damaged or oily.
HINT:
Oiliness may indicate a stuck PCV valve.
If necessary, replace the air cleaner element.
(b) Clean the element with compressed air.
First blow from back side thoroughly, then blow off the
front side of the element.
5. REPLACE AIR FILTER
Replace the used air cleaner element with a new one.
6. REPLACE ENGINE OIL AND OIL FILTER
(See page LU±2)
7. REPLACE ENGINE COOLANT
(See page CO±2)
8. INSPECT CHARCOAL CANISTER
(See page EC±9)
9. REPLACE GASKET IN FUEL TANK CAP
(See page SF±33)
10. INSPECT FUEL LINES, CONNECTIONS, FUEL TANK
VAPOR VENT SYSTEM HOSES AND FUEL TANK
BAND
Visually inspect the fuel lines for cracks, leakage loose connec-
tions, deformation or tank band looseness.
11. INSPECT EXHAUST PIPES AND MOUNTINGS
Visually inspect the pipes, hangers and connections for severe
corrosion, leaks or damage.
12. INSPECT VALVE CLEARANCE
(See page EM±4)

P23118Drain Plug Transfer
B07969
Differential
Front
RearDrain plug
Drain plug
B07952Drain Plug
MA0099
OK if coolOK if hot
Add if coolAdd if hot
± MAINTENANCECHASSIS
MA±9
56 Author: Date:
2005 SEQUOIA (RM1146U)
8. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Transfer:
Remove the transfer cover.
(b) Remove the drain plug and drain the oil.
(c) Reinstall the drain plug securely.
(d) Add new oil until it reaches the bottom of the filler hole.
Transfer oil: See page TR±4
Front differential oil: See page SA-38
Rear differential oil: See page SA±129
9. REPLACE AUTOMATIC TRANSMISSION FLUID
(a) Remove the drain plug and drain the fluid.
(b) Reinstall the drain plug securely.
(c) With the engine OFF, add new fluid through the dipstick
tube.
Transmission fluid (A/T): See page DI±524
(d) Start the engine and shift the selector into all positions
from ºPº through ºLº and then shift into ºPº.
(e) With the engine idling, check the fluid level.
Add fluid up to the ºCOOLº level on the dipstick.
(f) Check that the fluid level is in the ºHOTº range at the nor-
mal operating temperature (70 ± 80°C or 158 ± 176°F)
and add as necessary.
NOTICE:
Do not overfill.
10. RECOAT FRONT WHEEL BEARINGS AND THRUST
BUSH
(a) Recoat the front wheel bearing with grease (See page
SA±28).

PP42W±01
± PREPARATIONENGINE MECHANICAL
PP±3
61 Author: Date:
2005 SEQUOIA (RM1146U)
ENGINE MECHANICAL
SST (Special Service Tools)
09201±01055Valve Guide Bushing Remover & Re
placer 5.5
09201±41020Valve Stem Oil Seal Replacer
09202±70020Valve Spring Compressor
(09202±00010)Attachment
09213±70011Crankshaft Pully Holding Tool
(90105±08076)Bolt
(90119±08216)Bolt
09222±30010Connecting Rod Bushing Remover
& Replacer
09223±46011Crankshaft Front Oil Seal
ReplacerCrankshaft pulley
Crankshaft timing pulley
09223±56010Crankshaft Rear Oil Seal
Replacer
09330±00021Companion Flange Holding ToolCrankshaft pulley
09843±18030Tacho±pulse Pickup Wire No.2

PP1BN±07
PP±8
± PREPARATIONENGINE MECHANICAL
66 Author: Date:
2005 SEQUOIA (RM1146U)
SSM (Special Service Materials)
08826±00080Seal Packing Black or equivalent
(FIPG)Camshaft bearing cap
Cylinder head semi±circular plug
Cylinder head cover
Rear oil sear retainer
08826±00080Seal Packing Black or equivalent
(FIPG)Camshaft housing plug
08826±00100Seal Packing 1282B,
THREE BOND 1282B or equivalent
(FIPG)Coolant drain union
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalentDrive plate bolt
Torque converter clutch bolt
08833±00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentNo.1 idler pulley bolt

PP1AW±08
± PREPARATIONLUBRICATION
PP±21
79 Author: Date:
2005 SEQUOIA (RM1146U)
LUBRICANT
ItemCapacityClassification
Engine oil
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change
7.1 liters (7.5 US qts, 6.2 Imp. qts)
6.2 liters (6.6 US qts, 5.5 Imp. qts)
5.7 liters (6.0 US qts, 5.0 Imp qts)API grade SL Energy±Conserving or ILSAC mul-
tigrade engine oil.

PP0O2±06
± PREPARATIONBODY ELECTRICAL
PP±73
131 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

± SERVICE SPECIFICATIONSENGINE MECHANICAL
SS±5
147 Author: Date:
2005 SEQUOIA (RM1146U) Cylinder head
Warpage Maximum
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.05
Cylinder head bolt thread inside diameter STD
Minimum
Protrusion heightIntake
Exhaust0.10 mm (0.039 in.)
30°, 45°, 60°
45°
1.0 to 1.4 mm (0.039 to 0.055 in.)
10.285 to 10.306 mm (0.4049 to 0.4057 in.)
10.335 to 10.356 mm (0.4069 to 0.4077 in.)
9.810 to 9.960 mm (0.3862 to 0.3921 in.)
9.700 mm (0.3819 in.)
9.2 to 9.8 mm (0.362 to 0.386 in.)
8.2 to 8.8 mm (0.323 to 0.346 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD
O/S 0.055.510 to 5.530 mm (0.2169 to 0.2374 in.)
10.333 to 10.344 mm (0.4068 to 0.4072 in.)
10.383 to 10.394 mm (0.4088 to 0.4092 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum95.05 mm (3.7421 in.)
95.10 mm (3.7441 in.)
94.55 mm (3.7224 in.)
94.60 mm (3.7244 in.)
44.5°
5.470 to 5.485 mm (0.2154 to 0.2159 in.)
5.465 to 5.480 mm (0.2152 to 0.2157 in.)
0.025 to 0.060 mm (0.0010 to 0.0024 in.)
0.030 to 0.065 mm (0.0012 to 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.0 mm (0.039 in.)
0.5 mm (0.020 in.)
Valve springDeviation Maximum
Free length
Installed tension at 35.0 mm (1.378 in.)2.0 mm (0.079 in.)
54.1 mm (2.130 in.)
210 to 226 N (21.4 to 23.0 kgf, 47.2 to 50.7 lbf)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum30.968 to 30.976 mm (1.2192 to 2.2195 in.)
31.000 to 31.016 mm (1.2205 to 1.2211 in.)
0.024 to 0.050 mm (0.0009 to 0.0020 in.)
0.07 mm (0.0028 in.)
CamshaftThrust clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Journal oil clearance STD
Maximum
Timing tube journal oil clearance STD
Maximum
Journal diameter
Timing tube journal diameter STD
Circle runout
Cam lobe height STD Intake
Exhaust
Minimum Intake
Exhaust
Camshaft gear backlash STD
Maximum
Camshaft gear spring end free distance0 to 0.040 mm (0 to 0.0016 in.)
0.030 to 0.070 mm (0.0011 to 0.0028 in.)
0.12 mm (0.0047 in.)
0.10 mm (0.0039 in.)
0.030 to 0.071 mm (0.0012 to 0.0028 in.)
0.10 mm (0.0039 in.)
0.036 to 0.057 mm (0.0014 to 0.0022 in.)
0.075 mm (0.0030 in.)
26.954 to 26.970 mm (1.0612 to 1.0618 in.)
39.955 to 39.964 mm (1.5730 to 1.5734 in.)
0.03 mm (0.0012 in.)
42.61 to 42.71 mm (1.6776 to 1.6815 in.)
42.63 to 42.71 mm (1.6783 to 1.6823 in.)
42.46 mm (1.6717 in.)
42.48 mm (1.6724 in.)
0.020 to 0.200 mm (0.0008 to 0.0079 in.)
0.30 mm (0.0188 in.)
18.2 to 18.8 mm (0.712 to 0.740 in.)
ManifoldWarpageMaximum Exhaust0.10 mm (0.0039 in.)