shield TOYOTA SEQUOIA 2001 Service Repair Manual

IN0IG±04
BO4111
Negative Cable
± INTRODUCTIONFOR ALL OF VEHICLES
IN±9
9 Author: Date:
2005 SEQUOIA (RM1146U)
FOR ALL OF VEHICLES
PRECAUTION
1. FOR VEHICLES EQUIPPED WITH SRS AIRBAG AND
SEAT BELT PRETENSIONER
(a) The SEQUOIA is equipped with an SRS (Supplemental
Restraint System), such as the driver airbag, front pas-
senger airbag, side airbag assembly, curtain shield airbag
assembly and seat belt pretensioner.
Failure to carry out service operations in the correct se-
quence could cause the supplemental restraint system to
unexpectedly deploy during servicing, possibly leading to
a serious accident.
Further, if a mistake is made in servicing the supplemental
restraint system, it is possible the SRS may fail to operate
when required. Before servicing (including removal or
installation of parts, inspection or replacement), be sure
to read the following items carefully, then follow the cor-
rect procedure described in this manual.
(b) GENERAL NOTICE
(1) Malfunction symptoms of the supplemental re-
straint system are difficult to confirm, so the diag-
nostic trouble codes become the most important
source of information when troubleshooting. When
troubleshooting the supplemental restraint system,
always inspect the diagnostic trouble codes before
disconnecting the battery (See page DI±1118).
(2) Work must be started after 90 seconds from the
time the ignition switch is turned to the ºLOCKº posi-
tion and the negative (±) terminal cable is discon-
nected from the battery.
(The supplemental restraint system is equipped
with a back±up power source because if work is
started within 90 seconds of disconnecting the neg-
ative (±) terminal cable from the battery, the SRS
may deploy.)
When the negative (±) terminal cable is discon-
nected from the battery, memory of the clock and
audio systems will be cancelled. So before starting
work, make a record of the contents memorized in
each memory system. When work is finished, reset
the clock and audio systems as before. To avoid
erasing the memory of each memory system, never
use a back±up power supply from another battery.

IN±10
± INTRODUCTIONFOR ALL OF VEHICLES
10 Author: Date:
2005 SEQUOIA (RM1146U)
(3) Even in case of a minor collision where the SRS
does not deploy, the steering wheel pad, the pas-
senger airbag assembly, side airbag assembly, cur-
tain shield airbag assembly, seat belt pretensioner,
airbag sensor assembly, front airbag sensor, side
airbag sensor assembly and curtain shield airbag
sensor assembly should be inspected.
Parts of referenceSee page
Steering wheel padSee page RS±22
Passenger side airbag assemblySee page RS±35
Side airbag assembly
Power adjuster type
Manual adjuster type
See page RS±49
See page RS±64
Curtain shield airbag assemblySee page RS±72
Seat belt pretensionerSee page BO±165
Airbag sensor assemblySee page RS±83
Front airbag sensor assemblySee page RS±88
Side airbag sensor assemblySee page RS±93
Curtain shield airbag sensor assemblySee page RS±98
(4) Never use SRS parts from another vehicle. When
replacing parts, replace them with new ones.
(5) Before repairs, remove the airbag sensor because
shocks are likely to be applied to the sensor during
repairs.
(6) Never disassemble or repair the steering wheel
pad, front passenger airbag assembly, airbag sen-
sor assembly and front airbag sensor.
(7) If the steering wheel pad, front passenger airbag
assembly, side airbag assembly, curtain shield air-
bag assembly, seat belt pretensioner, airbag sensor
assembly and front airbag sensor have been
dropped, or if there are cracks, dents or other de-
fects in the case, bracket or connector, replace
them with new ones.
(8) Do not expose the steering wheel pad, front pas-
senger airbag assembly, side airbag assembly, cur-
tain shield airbag assembly, seat belt pretensioner,
airbag sensor assembly and front airbag sensor di-
rectly to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kW/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of
the SRS components. Follow the instructions on the
notices.
(11) After work on the supplemental restraint system is
completed, check the SRS warning light (See page
DI±1118).

H11622H12060B08604
Example:
CorrectWrong Clear Plastic Bag
R06952H12059B08605
Example:
± INTRODUCTIONFOR ALL OF VEHICLES
IN±15
15 Author: Date:
2005 SEQUOIA (RM1146U)
(g) CURTAIN SHIELD AIRBAG ASSEMBLY
(1) Always store a removed or new curtain shield air-
bag assembly in a clear plastic bag, and keep it in
a safe place.
NOTICE:
Protection bag is not reused.
CAUTION:
Never disassemble the curtain shield airbag assembly
(2) Never measure the resistance of the airbag squib
(This may cause the airbag to deploy, which is very
dangerous.).
(3) Grease should not be attached to the curtain shield
airbag assembly and the surface should not be
cleaned with any kind of detergents.
(4) Store the airbag assembly where the ambient tem-
perature remains below 93°C (200°F), without high
humidity and away from electrical noise.
(5) When using electric welding, first disconnect the air-
bag connector (yellow color and 2 pins) into the
instrument panel before starting work.
(6) When disposing of a vehicle or the curtain shield air-
bag assembly alone, the airbag should be deployed
using an SST before disposal (See page RS±73).
Perform the operation in a safe place away from
electrical noise.

IN±42
± INTRODUCTIONTERMS
42 Author: Date:
2005 SEQUOIA (RM1146U) H/B
Hatchback
H±FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HSGHousing
HTHard Top
HWSHeated Windshield System
ICIntegrated Circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, Valve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
ISCIdle Speed Control
J/BJunction Block
J/CJunction Connector
KDKick±Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft±Hand
LHDLeft±Hand Drive
L/H/WLength, Height, Width
LLCLong±Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Differential
LSP & PVLoad Sensing Proportioning And Bypass Valve
LSPVLoad Sensing Proportioning Valve
MAPManifold Absolute Pressure
MAX.Maximum
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MG1Motor Generator No.1
MG2Motor Generator No.2
MPMultipurpose
MPIMultipoint Electronic Injection
MPXMultiplex Communication System
M/T, MTMManual Transmission (Transaxle)
MTMount
MTGMounting
NNeutral
NANatural Aspiration
NO.Number
O2SOxygen Sensor
O/DOverdrive

MA001±42
± MAINTENANCEOUTSIDE VEHICLE
MA±1
48 Author: Date:
2005 SEQUOIA (RM1146U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing.
If necessary, tighten them.
4. TIRE ROTATION (See page SA±3)
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, find the cause and correct.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

MA002±35
MA±2
± MAINTENANCEINSIDE VEHICLE
49 Author: Date:
2005 SEQUOIA (RM1146U)
INSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified free play. Be alert for changes in steering condition, such as hard steering,
excessive free play or strange noises.
11. SEATS
(a) Check that the seat adjusters operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latch position.
(d) For fold±down seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.

MA003±50
MA±4
± MAINTENANCEUNDER HOOD
51 Author: Date:
2005 SEQUOIA (RM1146U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see±through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(2UZ±FE engine: See page CO±14)
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see±through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re±insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 ± 80°C, 158 ± 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, find the cause and
correct.

PP3JT±01
± PREPARATIONBODY
PP±75
133 Author: Date:
2005 SEQUOIA (RM1146U)
BODY
SST (Special Service Tools)
09082±00700SRS Airbag Deployment ToolSEAT BELT PRETENSIONER
09082±00740Airbag Deployment Wire
Sub±harness No.2SEAT BELT PRETENSIONER
09806±30010Windshield Moulding RemoverWINDSHIELD
ROOF DRIP SIDE FINISH
MOULDING
09812±00010Door Hinge Set Bolt WrenchFRONT DOOR

PP1AP±02
± PREPARATIONBODY
PP±79
137 Author: Date:
2005 SEQUOIA (RM1146U)
SSM (Special Service Materials)
08833±00030Three cement black or equivalent
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalent
08850±00801Windshield Glass Adhesive Set
or equivalent

SS061±77
SS±46
± SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
188 Author: Date:
2005 SEQUOIA (RM1146U)
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Steering wheel set nut5051037
Steering wheel pad set screw (Torx screw)8.89078 in.´lbf
Front passenger airbag assembly x Instrument panel5.05144 in.´lbf
Front passenger airbag assembly x Instrument panel reinforcement2020415
Front seat x Body3737727
Front seat inner belt x Front seat4142831
Seatback cover x Seatback frame5.55649 in.´lbf
Armrest x Seatback frame3737727
Cutain shield airbag assembly x Body9.81007
Airbag senaor assembly x Body17.517913
Front airbag sensor x Body17.517913
Side airbag sensor assembly x Body17.517913
Curtain shield airbag sensor assembly x Body17.517913
Seat position sensor assembly x Body8.08271 in.´lbf