oil temperature TOYOTA SEQUOIA 2001 Service Repair Manual

MA003±50
MA±4
± MAINTENANCEUNDER HOOD
51 Author: Date:
2005 SEQUOIA (RM1146U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see±through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(2UZ±FE engine: See page CO±14)
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see±through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re±insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 ± 80°C, 158 ± 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, find the cause and
correct.

B07270
MA04O±03
B07272
Drive Shaft Boots
B07271
Dust Cover
Z04824
A/T
OK if coolOK if hot
Add if coolAdd if hot
± MAINTENANCECHASSIS
MA±7
54 Author: Date:
2005 SEQUOIA (RM1146U)
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering wheel free play (See page SR±9).
(b) Check the steering linkage for looseness or damage.
Check that:

Tie rod ends do not have excessive play.

Dust seals are not damaged.

Boot clamps are not loose.
2. INSPECT SRS AIRBAG (See page RS±3)
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leaks.
If leakage is found, check the cause and repair.
4. 4WD:
INSPECT DRIVE SHAFT BOOTS
Inspect the drive shaft boots for clamp looseness, grease leak-
age or damage.
5. INSPECT BALL JOINTS AND DUST COVERS
(a) Inspect the ball joints for excessive looseness.
(b) Inspect the dust cover for damage.
6. 2WD:
CHECK OIL LEVEL IN AUTOMATIC TRANSMISSION
AND DIFFERENTIAL
(a) Automatic transmission:
Check that the fluid level is in the ºHOTº range at the nor-
mal operating temperature (70 ± 80°C or 158 ± 176°F)
and add as necessary.
NOTICE:
Do not overfill.
Transmission fluid (A/T): See page
DI±524

B07273
Filler Plug
Differential
Z04824
A/T
OK if coolOK if hot
Add if coolAdd if hot
P23117
Filler Plug
Transfer
B07968
Differential
Front
RearFiller Plug
Filler Plug MA±8
± MAINTENANCECHASSIS
55 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Differential:
Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole. If the level is low, add oil
until it reaches the bottom of the filler hole.
Differential oil: See page SA±129
7. 4WD:
CHECK OIL LEVEL IN AUTOMATIC TRANSMISSION,
TRANSFER AND DIFFERENTIAL
(a) Automatic transmission:
Check that the fluid level is in the ºHOTº range at the nor-
mal operating temperature (70 ± 80°C or 158 ± 176°F)
and add as necessary.
NOTICE:
Do not overfill.
Transmission fluid (A/T): See page DI±524
(b) Transfer:
Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole. If the level is low, add oil
until it reaches the bottom of the filler hole.
Transfer oil: See page TR±4
(c) Differential:
Remove the filler plug and feel inside the hole with your
finger. Check that the oil comes to within 5 mm (0.20 in.)
of the bottom edge of the hole. If the level is low, add oil
until it reaches the bottom of the filler hole.
Front differential oil: See page SA±38
Rear differential oil: See page SA±129

P23118Drain Plug Transfer
B07969
Differential
Front
RearDrain plug
Drain plug
B07952Drain Plug
MA0099
OK if coolOK if hot
Add if coolAdd if hot
± MAINTENANCECHASSIS
MA±9
56 Author: Date:
2005 SEQUOIA (RM1146U)
8. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Transfer:
Remove the transfer cover.
(b) Remove the drain plug and drain the oil.
(c) Reinstall the drain plug securely.
(d) Add new oil until it reaches the bottom of the filler hole.
Transfer oil: See page TR±4
Front differential oil: See page SA-38
Rear differential oil: See page SA±129
9. REPLACE AUTOMATIC TRANSMISSION FLUID
(a) Remove the drain plug and drain the fluid.
(b) Reinstall the drain plug securely.
(c) With the engine OFF, add new fluid through the dipstick
tube.
Transmission fluid (A/T): See page DI±524
(d) Start the engine and shift the selector into all positions
from ºPº through ºLº and then shift into ºPº.
(e) With the engine idling, check the fluid level.
Add fluid up to the ºCOOLº level on the dipstick.
(f) Check that the fluid level is in the ºHOTº range at the nor-
mal operating temperature (70 ± 80°C or 158 ± 176°F)
and add as necessary.
NOTICE:
Do not overfill.
10. RECOAT FRONT WHEEL BEARINGS AND THRUST
BUSH
(a) Recoat the front wheel bearing with grease (See page
SA±28).

PP0O2±06
± PREPARATIONBODY ELECTRICAL
PP±73
131 Author: Date:
2005 SEQUOIA (RM1146U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

DID7O±02
± DIAGNOSTICSENGINE
DI±3
197 Author: Date:
2005 SEQUOIA (RM1146U)
TOYOTA PART AND SYSTEM NAME LIST
This reference list indicates the part names used in this manual along with their definitions.
TOYOTA/LEXUS nameDefinition
Toyota HCAC system, Hydro±carbon Adsorptive Catalyst
(HCAC) system, HC adsorptive three±way catalystHC adsorptive three±way catalytic converter
Variable Valve Timing sensor, VVT sensorCamshaft position sensor
Variable valve timing system, VVT systemCamshaft timing control system
Camshaft timing oil control valve, Oil control valve, OCV,
VVT, VSVCamshaft timing oil control valve
Variable timing and lift, VVTLCamshaft timing and lift control
Crankshaft position sensor ºAºCrankshaft position sensor
Engine speed sensorCrankshaft position sensor
THAIntake air temperature
Knock control moduleEngine knock control module
Knock sensorEngine knock sensor
Mass or volume air flow circuitMass air flow sensor circuit
Vacuum sensorManifold air pressure sensor
Internal control module, Control module, Engine control
ECU, PCMPower train control module
FC idleDeceleration fuel cut
Idle air control valveIdle speed control
VSV for CCV, Canister close valve VSV for canister controlEvaporative emissions canister vent valve
VSV for EVAP, Vacuum switching valve assembly No. 1,
EVAP VSV, Purge VSVEvaporative emissions canister purge valve
VSV for pressure switching valve, Bypass VSVEvaporative emission pressure switching valve
Vapor pressure sensor, EVAP pressure sensor, Evaporative
emission control system pressure sensorFuel tank pressure sensor
Charcoal canisterEvaporative emissions canister
ORVR systemOn±board refueling vapor recovery system
Intake manifold runner controlIntake manifold tuning system
Intake manifold runner valve, IMRV, IACV (runner valve)Intake manifold tuning valve
Intake control VSVIntake manifold tuning solenoid valve
AFSAir fuel ratio sensor
O2 sensorHeater oxygen sensor
Oxygen sensor pumping current circuitOxygen sensor output signal
Oxygen sensor reference ground circuitOxygen sensor signal ground
Accel position sensorAccelerator pedal position sensor
Throttle actuator control motor, Actuator control motor, Elec-
tronic throttle motor, Throttle control motorElectronic throttle actuator
Electronic throttle control system, Throttle actuator control
systemElectronic throttle control system
Throttle/pedal position sensor, Throttle/pedal position switch,
Throttle position sensor/switchThrottle position sensor
Turbo press sensorTurbocharger pressure sensor
Turbo VSVTurbocharger pressure control solenoid valve
P/S pressure switchPower±steering pressure switch
VSV for ACMActive control engine mount

DID82±01
A20891
Mass Air Flow Sensor Crankshaft Position Sensor
Actual Valve TimingCorrection Target Valve Timing
Feedback
Duty Control ECM
Camshaft Timing
Oil Control
Valve (OCV)
Vehicle Speed Signal Engine Coolant Temp. Sensor Throttle Position Sensor
Camshaft Position Sensor
± DIAGNOSTICSENGINE
DI±73
267 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC P0010 Camshaft Position ºAº Actuator circuit
(Bank 1)
DTC P0020 Camshaft Position ºAº Actuator circuit
(Bank 2)
CIRCUIT DESCRIPTION
The Variable Valve Timing (VVT) system includes the ECM, the Oil Control Valve (OCV) and the VVT control-
ler. The ECM sends a target ºduty±cycleº control signal to the OCV. This control signal, applied to the OCV,
regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on en-
gine operation conditions such as intake air volume, throttle position and engine coolant temperature.
The ECM controls the OCV, based on the signals output from the sensors. The VVT controller regulates the
intake camshaft angle using oil pressure through the OCV. As a result, the relative position between the cam-
shaft and the crankshaft is optimized, and the engine torque improves, fuel economy improves, and exhaust
emissions decrease under overall driving conditions. Also, the ECM detects the actual valve timing using
signals from the camshaft position sensor and the crankshaft position sensor, and performs feedback con-
trol. This is how target valve timing is verified by the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P0010
P0020Open or short in OCV circuit

Open or short in OCV circuit

OCV

ECM

A21026
Component Side
C2
Crankshaft Position Sensor
± DIAGNOSTICSENGINE
DI±213
407 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:

Read freeze frame data using the hand±held tester. Freeze frame records the engine conditions when
a malfunction is detected. When troubleshooting it is useful for determining whether the vehicle was
running or stopped. the engine was warmed up or not, the air±fuel ratio lean or rich, etc. at the time
of the malfunction.

READ VALUE ON HAND±HELD TESTER
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and push the hand±held tester tool main switch ON.
(c) When using hand±held tester, enter the following menu: ºDIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / ENGINE SPDº.

The engine speed can be confirmed in DATA LIST using the hand±held tester. If there are no NE sig-
nals from the crankshaft position sensor despite the engine revolving, the engine speed will be indi-
cated as zero. If voltage output of the crankshaft position sensor is insufficient, the engine speed will
be indicated as lower RPM (than the actual RPM).
1 Check resistance of crankshaft position sensor.
PREPARATION:
Disconnect the C2 crankshaft position sensor connector.
CHECK:
Measure the resistance between terminals 1 and 2.
OK:
Standard:
Tester ConnectionSpecified Condition
1 ± 2985 to 1,600 W at cold
1 ± 21,265 to 1,890 W at hot
NOTICE:
º Coldº and ºHotº shown above mean the temperature of
the coils themselves. ºColdº is form ±10°C (14°F) to 50°C
(122°F) and ºHotº is from 50°C (122°F) to 100°C (212°F).
NG Replace crankshaft position sensor.
OK

DIDIJ±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±517
711 Author: Date:
2005 SEQUOIA (RM1146U)
TOYOTA PART AND SYSTEM NAME LIST
This reference list indicates the part names used in this manual along with their definitions.
Part and system nameDefinition
Toyota HCAC system, Hydrocarbon adsorptive Catalyst
(HCAC) system, HC adsorptive three±way catalystHC adsorptive three±way catalytic converter
Variable Valve Timing sensor, VVT sensorCamshaft position sensor
Variable valve timing system, VVT systemCamshaft timing control system
Camshaft timing oil control valve, Oil control valve OCV,
VVT, VSVCamshaft timing oil control valve
Variable timing and lift, VVTLCamshaft timing and lift control
Crankshaft position sensor ºAºCrankshaft position sensor
Engine speed sensorCrankshaft position sensor
THAIntake air temperature
Knock control moduleEngine knock control module
Knock sensorEngine knock sensor
Mass or volume air flow circuitMass air flow sensor circuit
Vacuum sensorManifold air pressure sensor
Internal control module, Control module, Engine control
ECU, PCMPower train control module
FC idleDeceleration fuel cut
Idle air control valveIdle speed control
VSV for CCV, Canister close valve VSV for canister controlEvaporative emissions canister vent valve
VSV for EVAP, Vacuum switching valve assembly No. 1,
EVAP VAV, Purge VSVEvaporative emissions canister purge valve
VSV for pressure switching valve, Bypass VSVEvaporative emission pressure switching valve
Vapor pressure sensor, EVAP pressure sensor, Evaporative
emission control system pressure sensorFuel tank pressure sensor
Charcoal canisterEvaporative emissions canister
ORVR systemOn±board refueling vapor recovery system
Intake manifold runner controlIntake manifold tuning system
Intake manifold runner valve, IMRV, IACV (runner valve)Intake manifold tuning valve
Intake control VSVIntake manifold tuning solenoid valve
AFSAir fuel ratio sensor
O2 sensorHeater oxygen sensor
Oxygen sensor pumping current circuitOxygen sensor output signal
Oxygen sensor reference ground circuitOxygen sensor signal ground
Accel position sensorAccelerator pedal position sensor
Throttle actuator control motor, Actuator control motor, Elec-
tronic throttle motor, Throttle control motorElectronic throttle actuator
Electronic throttle control system, Throttle actuator control
systemElectronic throttle control system
Throttle/pedal position sensor, Throttle/pedal position switch,
Throttle position sensor/switchThrottle position sensor
Turbo press sensorTurbocharger pressure sensor
Turbo VSVTurbocharger pressure control solenoid valve
P/S pressure switchPower±steering pressure switch
VSV for ACMActive control engine mount
Speed sensor, Vehicle speed sensor ºAº, Speed sensor for
skid control ECUVehicle speed sensor
ATF temperature sensor, Trans. fluid temp. sensor, ATF
temperature sensor ºAºTransmission fluid temperature sensor
Electronic controlled automatic transmission, ECTElectronically controlled automatic
Intermediate shaft speed sensor ºAºCounter gear speed sensor

DIDIK±01
D13871
Combination Meter
DLC3 Stop Light SwitchECM
Park/Neutral Position SwitchSpeed Sensor (SP2) Shift Solenoid Valve S1
Shift Solenoid Valve SR
Shift Solenoid Valve SLU
Shift Solenoid Valve SL2 ATF Temperature
Sensor No. 2Integration Control and Panel
(Shift Position L Switch)
MIL
Shift Solenoid Valve SL1
Shift Solenoid
Valve SLT
ATF Temperature
Sensor No.1
Shift Solenoid Valve S2
Speed Sensor (NT)

AT Oil Temp Warning LightShift Lever
(O/D Main Switch)
4WD:
4WD Control ECU
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±519
713 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION