oil filter TOYOTA SIENNA 2007 Service Owner's Guide

LU–42GR-FE LUBRICATION – OIL AND OIL FILTER
LU
REPLACEMENT
CAUTION:
• Prolonged and repeated contact with engine oil will
result in the removal of natural oils from the skin,
leading to dryness, irritation and dermatitis. In
addition, used engine oil contains potentially harmful
contaminants which may cause skin cancer.
• Precautions should be taken when replacing engine
oil to minimize the risk of your skin making contact
with used engine oil. Protective clothing and gloves
that cannot be penetrated by oil should be worn. The
skin should be washed with soap and water, or
waterless hand cleaner, to remove any used engine oil
thoroughly. Do not use gasoline, thinners, or solvents.
• In order to preserve the environment, used oil and
used oil filters must be disposed of at designated
disposal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug, and drain the oil into a
container.
(c) Clean and install the oil drain plug with a new
gasket.
Torque: 40 N*m (408 kgf*cm, 30 ft.*lbf)
2. REMOVE OIL FILTER ELEMENT
(a) Connect the hose with an inside diameter of 15 mm
(0.59 in.) to the pipe.
(b) Remove the oil filter drain plug from the oil filter cap.
A127996E01
A127997

2GR-FE LUBRICATION – OIL AND OIL FILTERLU–5
LU
(c) Insert the pipe with the hose into the oil filter cap.
NOTICE:
Be sure to insert the pipe with the O-ring
installed on the oil filter cap side.
HINT:
Place the hose end into a container before draining
oil from the hose.
(d) Make sure that oil is completely drained, and
remove the pipe and O-ring.
HINT:
Be sure to turn the pipe in the direction of the arrow
to remove it.
(e) Using SST, remove the oil filter cap.
SST 09228-06501
(f) Remove the oil filter element and O-ring from the oil
filter cap.
NOTICE:
Do not use any tools to remove the O-ring in
order to prevent the cap from being damaged.
Be sure to remove it by hand.
A160741E01
A127999
A128000E01
A128001E01

LU–62GR-FE LUBRICATION – OIL AND OIL FILTER
LU
3. INSTALL OIL FILTER ELEMENT
(a) Clean the inside of the oil filter cap, threads, and O-
ring groove.
(b) Apply a light coat of engine oil to a new O-ring and
install it to the oil filter cap.
NOTICE:
Make sure that the O-ring does not get twisted
on the groove.
(c) Install a new oil filter element to the oil filter cap.
(d) Remove all dirt and foreign matter from the
installation surface and the inside of the cap on the
engine side.
(e) Apply a light coat of engine oil to the O-ring again
and install the oil filter cap.
NOTICE:
Make sure that the O-ring does not get caught
between the parts.
(f) Using SST, install the oil filter cap.
SST 09228-06501
Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf)
NOTICE:
Make sure that there is no clearance between
the parts after tightening the oil filter cap.
(g) Apply a light coat of engine oil to a new O-ring and
install it to the oil filter cap.
NOTICE:
Remove all dirt and foreign matter from the
installation surface.
(h) Install the oil filter drain plug to the oil filter cap.
Torque: 13 N*m (127 kgf*cm, 10 ft.*lbf)
NOTICE:
Make sure that the O-ring does not get caught
between the parts.
4. ADD ENGINE OIL
(a) Add clean engine oil and install the oil filler cap.
Engine oil
Capacity:
5. INSPECT FOR OIL LEAK
(a) Start the engine. Check for engine oil leaks from the
connected parts of the oil filter cap and oil filter drain
plug.
A128001E02
A128002E01
A161390E01
Oil Grade Oil Viscosity (SAE)
ILSAC multigrade engine oil 5W-30
Item Standard Condition
Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 lmp. qts)
Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 lmp. qts)
Dry fill 7.1 liters (7.5 US qts, 6.2 lmp. qts)