low beam TOYOTA SIENNA 2018 Owners Manual (in English)

5
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
1
If indicator does not turn off within a few seconds of starting engine, there may be a malfunction.
Have vehicle inspected by your Toyota dealer.
2 If this light flashes, refer to “Dynamic Radar Cruise Control,” Section 4-5, 2018 Owner’s Manual.3 If equipped.
Turn signal indicator
Fog light indicator3
High coolant temperature warning
Low engine oil pressure warning
1
Low Tire Pressure Warning1
Master warning light1
Low fuel level warning light
Lane Departure Alert (LDA) indicator
Low engine oil level warning
Electric power steering system
warning light1
Security indicator
ECO Driving Indicator Light1
ECT PWR indicator
Low outside temperature indicator
Vehicle Stability Control OFF
indicator1
Third seat fold incomplete
warning3
Slip indicator/Hill-start Assist
Control indicator1,5
Low windshield washer fluid level
warning
Rear Cross Traffic Alert
(RCTA) indicator3
Malfunction/Check Engine
indicator1
Pre-Collision System (PCS)
warning1
Headlight low/high
beam indicator

11
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Lights & turn signals
Parking brake
Set: Depress
Release: Depress again
High beam flasher
Low beam Headlights
Daytime Running Light system (DRL) Automatically turns on the headlights at a
reduced intensity on some models.
Automatic light cut off system Automatically turns lights off after a delay of 30
seconds, or the lock switch on remote may be pushed after locking.
Automatic High Beam (AHB) system Automatically switches between high
and low beams as appropriate to provide the most light possible and enhance
forward visibility. Refer to Toyota Safety Sense™ P (TSS-P) in this guide or the
Owner’s Manual for more details on the Automatic High Beam feature.
* Operating conditions must be met. Refer to Owner’s Manual for details.
Parking lights
High beam
Auto or OFF
DRL OFF
Auto High Beam* or
Front fog lights come on only when the headlights are on low beam.
Turn
FRONT FOG LIGHTS (IF EQUIPPED)
HEADLIGHTS

12
FEATURES & OPERATIONS
Rotating the dial downward will lower the angle of the beam.
Up
Down
DownUp
Right turn
Lane change
Lane change
Left turn
Wash and wipe
Wipe
Interval wipe
Wash and
wipeOff
Windshield wipers & washers
*Intermittent windshield wiper
frequency adjustment Rotate to
increase/decrease wipe frequency.* Rain-sensing windshield wiper Rotate
to increase/decrease sensor sensitivity. Intermittent
Adjust frequency* Adjust frequency*Single wipeSingle wipe
Interval wipeInterval wipe
Slow Slow
FastFastPull to wash
and wipePull to wash
and wipe Off Off
Rain-sensing (if equipped)
FRONT
REAR
TURN SIGNALS
HEADLIGHT BEAM LEVEL CONTROL (IF EQUIPPED)

40
TOYOTA SAFETY SENSE™
Automatic High Beams (AHB)
(1) With the engine switch in IGNITION ON mode and headlight switch turned to
“AUTO” position, push lever away from you.
The “
” indicator will come on when the headlights are turned on
automatically to indicate that the system is active.
(2) Pull the lever back toward you to turn the AHB system off.
The “
” will turn off and the “” turns on.
When all of these conditions are met, high beams will be automatically turned on
(after approximately 1 second):
• Vehicle speed is above approximately 20 mph (32 km/h).
• The area ahead of the vehicle is dark.
• There are no oncoming or preceding vehicles with headlights or tail lights
turned on.
• There are few street lights on the road ahead.
If any of these conditions occur, the system is designed to automatically turn off
high beams:
• Vehicle speed drops below approximately 20 mph (32 km/h).
• The area ahead of the vehicle is not dark.
• Oncoming or preceding vehicles have headlights or tail lights
turned on.
• There are many streetlights on the road ahead.
ACTIVATING THE AHB SYSTEM
CONDITIONS WHERE AHB WILL TURN ON/OFF AUTOMATICALLY
AHB is a safety system designed to help drivers see more of what’s ahead at
nighttime without dazzling other drivers. When enabled, AHB uses an in-vehicle
camera to help detect the headlights of oncoming vehicles and tail lights of
preceding vehicles, then automatically switches between high and low beams
as appropriate to provide the most light possible and enhance forward visibility.
By using high beams more frequently, the system may allow earlier detection of
pedestrians and obstacles.
Refer to a Toyota Owner’s Manual for additional information on AHB operation,
settings adjustments, limitations, and precautions before attempting to use it.