warning light TOYOTA SUPRA 1986 Service Repair Manual

24
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[2JZ±GTE]
A 1 A/C Ambient Temp. Sensor E 4 Engine Coolant Temp. Sender (Water Temp. Sender)
A 2 A/C Condenser Fan Motor E 5 Engine Coolant Temp. SW (Water Temp. SW)
A 3 A/C Triple Pressure SW E 6 Engine Hood Courtesy SW
(A/C Dual and Single Pressure SW) E 7 Engine Oil Level Sensor
A 4 A/C Magnetic Clutch and Lock Sensor
A 5 A/T Fluid Temp. Sensor F 1 Front Airbag Sensor LH
A 6 ABS Actuator F 2 Front Airbag Sensor RH
A 7 ABS Actuator F 3 Front Fog Light and Parking Light LH
A 10 ABS Speed Sensor Front LH F 4 Front Fog Light and Parking Light RH
A 11 ABS Speed Sensor Front RH F 5 Front Side Marker Light LH
F 6 Front Side Marker Light RH
B 1 Back±Up Light SW (for M/T) F 7 Front Turn Signal Light LH
B 2 Brake Fluid Level Warning SW F 8 Front Turn Signal Light RH
F 9 Front Wiper Motor
C 1 Camshaft Position Sensor No. 1
C 2 Camshaft Position Sensor No. 2 G 1 Generator (Alternator)
C 3 Crankshaft Position Sensor G 2 Generator (Alternator)
C 4 Cruise Control Actuator
H 1 Headlight Hi LH
D 1 Data Link Connector 1 (Check Connector) H 2 Headlight Hi RH
D 2 Daytime Running Light Relay No. 3 H 3 Headlight Lo LH
D 3 Daytime Running Light Relay No. 3 H 4 Headlight Lo RH
H 5 Heated Oxygen Sensor (Main)
E 1 EGR Gas Temp. Sensor H 8 Horn LH
E 2 Electronically Controlled Transmission Solenoid H 9 Horn RH
E 3 Engine Coolant Temp. Sensor (EFI Water Temp. Sensor)

26
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[2JZ±GE]
A 1 A/C Ambient Temp. Sensor E 2 Electronically Controlled Transmission Solenoid
A 3 A/C Dual Pressure SW E 3 Engine Coolant Temp. Sensor (EFI Water Temp.
A 4 A/C Magnetic Clutch and Lock Sensor Sensor)
A 5 A/T Fluid Temp. Sensor E 4 Engine Coolant Temp. Sender (Water Temp.
A 6 ABS Actuator Sender)
A 7 ABS Actuator E 6 Engine Hood Courtesy SW
A 8 ABS Relay E 7 Engine Oil Level Sensor
A 9 ABS Relay
A 10 ABS Speed Sensor Front LH F 1 Front Airbag Sensor LH
A 11 ABS Speed Sensor Front RH F 2 Front Airbag Sensor RH
F 3 Front Fog Light and Parking Light LH
B 1 Back-Up Light SW (for M/T) F 4 Front Fog Light and Parking Light RH
B 2 Brake Fluid Level Warning SW F 5 Front Side Marker Light LH
F 6 Front Side Marker Light RH
C 4 Cruise Control Actuator F 7 Front Turn Signal Light LH
F 8 Front Turn Signal Light RH
D 1 Data Link Connector 1 (Check Connector) F 9 Front Wiper Motor
D 4 Distributor
G 1 Generator (Alternator)
E 1 EGR Gas Temp. Sensor G 2 Generator (Alternator)

29
Position of Parts in Instrument Panel
E 8 Electronically Controlled Transmission Pattern O 5 O/D Main SW and A/T Indicator Light (for Shift
Select SW Lever)
E 9 Engine Control Module (Engine and Electronically
Controlled Transmission ECU) P 4 PPS ECU
E 10 Engine Control Module (Engine and Electronically P 5 Parking Brake SW
Controlled Transmission ECU)
E 11 Engine Coolant Temp. Sensor (Water Temp. Sensor) R 4 Radio and Player (w/o Stereo Power Amplifier)
(for A/C System) R 5 Radio and Player (w/o Stereo Power Amplifier)
R 6 Radio and Player (w/ Stereo Power Amplifier)
F 10 Front Tweeter (Speaker) LH R 7 Remote Control Mirror SW
F 11 Front Tweeter (Speaker) RH R 8Rheostat
G 3 Glove Box Light S 6 Seat Heater SW
G 4 Glove Box Light SW S 7 Shift Lock ECU
S 8 Stereo Power Amplifier
H 10 Hazard SW S 9 Stereo Power Amplifier
H 11 Heated Oxygen Sensor (Sub) S 10 Stereo Power Amplifier
H 12 Heater Control SW S 11 Stop Light SW
H 13 Heater Control SW S 16 Sub Heated Oxygen Sensor
(for California)
I 18 Ignition Key Cylinder Light
I 19 Ignition SW T 5 Telltale Light LH
I 20 Integration Relay T 6 Telltale Light RH
T 7 Theft Deterrent ECU
J 1 Junction Connector T 8 TRAC Off SW
J 2 Junction Connector T 9 Traction ECU
T 10 Traction ECU
K 3 Key Interlock Solenoid T 13 Theft Deterrent ECU
K 4 Kick Down SW
U 1 Unlock Warning SW
N 2 Noise Filter

46
POWER SOURCE (Current Flow Chart)*1: (FOR CANADA)
*2: (FOR USA)
A/C Condenser Fan Motor
228
A2 *Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
Location
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.


7.5A HTR
7.5A IGN
7.5A RAD No. 2
7.5A ST
7.5A TURN
10A ECU±B
10A ECU±IG
10A GAUGE
10A MIR±HTR
10A PANEL
10A TAIL
15A CIG
15A SEAT±HTR
15A STOP
20A WIPER
30A DEFOG
30A DOOR
7.5A ALT±S
7.5A DOME
7.5A DRL
7.5A TRAC
15A FOG
15A HAZ±HORN
15A HEAD (LH) *2
15A HEAD (LH±LWR) *1
15A HEAD (LH±UPR) *1
15A HEAD (RH) *2
15A HEAD (RH±LWR) *1
15A HEAD (RH±UPR) *1
20A RAD No. 1
30A ABS No. 2
30A EFI No. 1
30A EFI No. 2
30A FAN
50A HTR
50A MAIN
60A ABS No. 1
60A POWERA3 A4 A6 A8 A9 A12 A14 A18 A19 A20 A22 A23 A24 A29 A30 A33 B1 B2 B4 B6 B7 228 228159
164159 159 228208
228159 159 164 164159
164228 122 210 210 116164
220228 206 206
A/C Single Pressure SW
[A/C Triple Pressure SW]
A/C Magnetic Clutch and
Lock Sensor
ABS Actuator
ABS Relay
A/C Amplifier
ABS ECU
ABS and Traction ECU
ABS Lateral Acceleration
Sensor
Air Inlet Control Servo Motor
Ashtray Illumination
Auto Antenna Control Relay
Auto Antenna Motor
Back±Up Light SW (for M/T)
Brake Fluid Level Warning SW
Blower Motor Control Relay
Buckle SW LH
Buckle SW RH
[LOCATION](1): J/B No. 1 (See page 20)(2): R/B No. 2 (See page 19)(3): R/B No. 4 (See page 23)
20 22
23

47
197
Center Airbag Sensor
Assembly
C5 C6 C10 C11D5 C7D1 D2 D3 C13 C8 C9 C12 C14 C15 C16 186 122 186 60
70
130 64
82
220159
140
150
164
174
220
122 70
82
181
228111140
150
22022094
9611194
96106 129
94
96
102
108
122
111 126 203 174140
150
17496 96 70
140
159 82
150
164
197
70
82
164
174
197
Cigarette Lighter
Cigarette Lighter
Illumination
Clock
Clutch Start SW
Brake Warning Light
[Comb. Meter]
Combination Meter
Meter Illumination
[Comb. Meter]
Speedometer
[Comb. Meter]
Turn Signal Indicator
Light [Comb. Meter]
Combination Meter
High Beam Indicator
Light [Comb. Meter]
Turn Signal Indicator
Light [Comb. Meter]
Dimmer SW [Comb. SW]
Fog Light SW [Comb. SW]
Horn SW [Comb. SW]
Light Control SW
[Comb. Meter]
Turn Signal SW
[Comb. Meter]
Front Wiper and Washer
SW [Comb. Meter]
Rear Wiper and Washer
SW [Comb. Meter]
Cruise Control Clutch SW
Cruise Control ECU
Data Link Connector 1
(Check Connector)
Daytime Running Light
Relay No. 3
Data Link Connector 2
(TDCL)
(4): R/B No. 5 (See page 20)
23

52
POWER SOURCE (Current Flow Chart)*1: (FOR CANADA)
*2: (FOR USA)
*Page Nos. of
Related Systems
Parts
Code or
Location
CB or FuseT5 70
82
Location
Malfunction Indicator Lamp
(Check Engine Warning Light)
[Telltale Light LH]
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.


7.5A HTR
7.5A IGN
7.5A RAD No. 2
7.5A ST
7.5A TURN
10A ECU±B
10A ECU±IG
10A GAUGE
10A MIR±HTR
10A PANEL
10A TAIL
15A CIG
15A SEAT±HTR
15A STOP
20A WIPER
30A DEFOG
30A DOOR
7.5A ALT±S
7.5A DOME
7.5A DRL
7.5A TRAC
15A FOG
15A HAZ±HORN
15A HEAD (LH) *2
15A HEAD (LH±LWR) *1
15A HEAD (LH±UPR) *1
15A HEAD (RH) *2
15A HEAD (RH±LWR) *1
15A HEAD (RH±UPR) *1
20A RAD No. 1
30A ABS No. 2
30A EFI No. 1
30A EFI No. 2
30A FAN
50A HTR
50A MAIN
60A ABS No. 1
60A POWERT6
T7
T8T9 T11 T12V1
V2V3
V4 V5 V6 V7 164
22068 118102
11 4194 197
70
122
150
181 82
140
174
220
228 60
64
130122 164 206 206 8270
8270
8270 7070
8270
Telltale Light LH
Charge Warning Light
[Telltale Light RH]
Open Door Warning Light
[Telltale Light RH]
Rear Light Warning Light
[Telltale Light RH]
Seat Belt Warning Light
[Telltale Light RH]
SRS Warning Light
[Telltale Light RH]
Telltale Light RH
Theft Deterrent ECU
TRAC Off SW
Traction ECU
Tension Reducer Solenoid LH
Tension Reducer Solenoid RH
VSV (for ACIS)
VSV (for EGR)
VSV (for EVAP)
VSV (for Exhaust Bypass
Valve)
VSV (for Exhaust Gas
Control Valve)
VSV (for Fuel Pressure Up)
VSV (for Intake Air
Control Valve)
[LOCATION](1): J/B No. 1 (See page 20)(2): R/B No. 2 (See page 19)(3): R/B No. 4 (See page 23)
20 22
23

68
CHARGING*
1:2JZ±GTE
*2 : 2JZ±GE
123E 81E12
LIG S B
IC REGULATOR
BW
W
B±O Y±G
Y±G
Y
WY
W
BATTERY10A
GAUGE 7. 5A
IG N
GENERATOR
(
ALTERNATOR) AAA B 123 1 II1 34 II123
W
W
A G1 ,G2B FROM POW ER SOURCE SYSTEM(
SEE PAGE 56)
EA2 4
EA3 2(*
1)
(*
2)
W
22
7. 5A
ALT±S 22
11 120A
ALT
W
W
2A 1I14
Y±G Y±G
Y±G FR OM
COM B INA TIO N
METERCHARGE WARNING LIGHT
[TELLTALE LIGHT RH] T6
1

71
2. CONTROL SYSTEM
*SEQUENTIAL MULTIPORT FUEL INJECTION (ELECTRONIC FUEL INJECTION) SYSTEM
THE SEQUENTIAL MULTIPORT FUEL INJECTION (ELECTRONIC FUEL INJECTION) SYSTEM MONITORS THE ENGINE CONDITION
THROUGH THE SIGNALS INPUT FROM EACH SENSOR (INPUT SIGNALS FROM (1) TO (13) ETC.) TO THE ENGINE CONTROL
MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU). THE BEST FUEL INJECTION TIMING IS DECIDED
BASED ON THIS DATA AND THE PROGRAM MEMORIZED BY THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU), AND THE CONTROL SIGNAL IS OUTPUT TO TERMINALS #10, #20, #30, 40, #50 AND #60 OF
THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) TO OPERATE THE
INJECTOR (INJECT THE FUEL). THE SEQUENTIAL MULTIPORT FUEL INJECTION (ELECTRONIC FUEL INJECTION) SYSTEM
PRODUCES CONTROLS OF FUEL INJECTION OPERATION BY THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU) IN RESPONSE TO THE DRIVING CONDITIONS.
*ESA (ELECTRONIC SPARK ADVANCE) SYSTEM
THE ESA SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT TO THE ENGINE CONTROL MODULE
(ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) FROM EACH SENSOR (INPUT SIGNALS FROM (1), (2), (4) TO
(13) ETC.). THE BEST IGNITION TIMING IS DECIDED ACCORDING TO THIS DATA AND THE MEMORIZED DATA IN THE ENGINE
CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) AND THE CONTROL SIGNAL IS OUTPUT
TO TERMINALS IGT1, IGT2, IGT3, IGT4, IGT5 AND IGT6 THESE SIGNALS CONTROL THE IGNITER TO PROVIDE THE BEST IGNITION
TIMING FOR THE DRIVING CONDITIONS.
*HEATED OXYGEN SENSOR HEATER CONTROL SYSTEM
THE MAIN HEATED OXYGEN SENSOR, SUB HEATED OXYGEN SENSOR HEATER CONTROL SYSTEM TURNS THE HEATER ON
WHEN THE INTAKE AIR VOLUME IS LOW (TEMP. OF EXHAUST EMISSIONS IS LOW), AND WARMS UP THE OXYGEN SENSOR TO
IMPROVE DETECTION PERFORMANCE OF THE SENSOR. THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU) EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (2), (4), (9) TO
(11) ETC.), AND OUTPUTS CURRENT TO TERMINALS HT1, HT2 TO CONTROL THE HEATER.
*IDLE AIR CONTROL (IDLE SPEED CONTROL) SYSTEM
THE IDLE AIR CONTROL (ISC) SYSTEM (STEP MOTOR TYPE) INCREASES THE ENGINE SPEED AND PROVIDES IDLING STABILITY
FOR FAST IDLE±UP WHEN THE ENGINE IS COLD, AND WHEN THE IDLE SPEED HAS DROPPED DUE TO ELECTRICAL LOAD AND SO
ON. THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) EVALUATE THE
SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (5), (8), (9), (11) ETC.), OUTPUTS CURRENT TO TERMINALS ISC1,
ISC2, ISC3 AND ISC4 TO CONTROL THE IDLE AIR CONTROL VALVE (ISC VALVE).
*EGR CONTROL SYSTEM
THE EGR CONTROL SYSTEM DETECTS THE SIGNAL FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (9), (10) ETC.), AND
OUTPUTS CURRENT TO TERMINAL EGR TO CONTROL THE EGR VALVE.
*FUEL PUMP CONTROL SYSTEM
THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) OUTPUTS CURRENT TO
TERMINAL FPC AND CONTROLS THE FUEL PUMP ECU AND FUEL PUMP DRIVE SPEED IN RESPONSE TO THE DRIVING
CONDITIONS.
3. DIAGNOSIS SYSTEM
WITH THE DIAGNOSIS SYSTEM, WHEN THERE IS A MALFUNCTION IN THE ENGINE CONTROL MODULE (ENGINE AND
ELECTRONICALLY CONTROLLED TRANSMISSION ECU) SIGNAL SYSTEM, THE MALFUNCTIONING SYSTEM IS RECORDED IN THE
MEMORY. THE MALFUNCTIONING SYSTEM CAN BE FOUND BY READING THE CODE DISPLAYED BY THE MALFUNCTION INDICATOR
LAMP (CHECK ENGINE WARNING LIGHT).
4. FAIL±SAFE SYSTEM
WHEN A MALFUNCTION HAS OCCURRED IN ANY SYSTEM, IF THERE IS A POSSIBILITY OF ENGINE TROUBLE BEING CAUSED BY
CONTINUED CONTROL BASED ON THE SIGNALS FROM THAT SYSTEM, THE FAIL±SAFE SYSTEM EITHER CONTROLS THE SYSTEM
BY USING DATA (STANDARD VALUES) RECORDED IN THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU) MEMORY OR ELSE STOPS THE ENGINE.

77
* 1 : ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU
I14 10A
GAUGE
I14
I5
II1 2II123 II18
IJ1 13 IJ1 5 IJ1 171E 12
II1 15 II111 IF173 2
1 3
IF ENG TE 1 TE2 E1W TT
2 15
67
7 1 2 38 5L±BL±RY
Y±L
LG
P BR GR±R
L±BBR
PL±B
P
BR
L±R
Y
RYY Y
Y
L±B LG P±G
Y±L
V10
VEHICLE SPEED SENSOR
(
SPEED SENSOR)
NO. 1
(
FOR COMBI NA TI ON M ETER) ODO AND
TRIP
TELLTALE LIGHT RHMALFUNCTION INDICATOR LAMP
(
CHECK ENGINE WARNING LIGHT)
[TELLTALE LIGHT LH] T5
T6
FROM POWER SOURCESYSTEM(
SEE PAGE 56)
L±B
DATA LINK
CONNECTOR 2
(
TDCL) D5I14I14
A 11 A10 B11 A 9
L±R
Y Y
R
BR
Y
L±R
SPEEDOMETER
[COMB. METER]B C10 , C12A
P±G
L±B
BR
(
A/T)
I8

83
(13) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR FRONT AND REAR SIDE AND THE SIGNAL IS INPUT INTO TERMINALS
KNK1 AND KNK2 AS A CONTROL SIGNAL.
2. CONTROL SYSTEM
*SEQUENTIAL MULTIPORT FUEL INJECTION (ELECTRONIC FUEL INJECTION) SYSTEM
THE SEQUENTIAL MULTIPORT FUEL INJECTION (ELECTRONIC FUEL INJECTION) SYSTEM MONITORS THE ENGINE CONDITION
THROUGH THE SIGNALS INPUT FROM EACH SENSOR (INPUT SIGNALS FROM (1) TO (13) ETC.) TO THE ENGINE CONTROL
MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU). THE BEST FUEL INJECTION TIMING IS DECIDED
BASED ON THIS DATA AND THE PROGRAM MEMORIZED BY THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU), AND THE CONTROL SIGNAL IS OUTPUT TO TERMINALS #10, #20, #30, 40, #50 AND #60 OF
THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) TO OPERATE THE
INJECTOR (INJECT THE FUEL). THE SEQUENTIAL MULTIPORT FUEL INJECTION (ELECTRONIC FUEL INJECTION) SYSTEM
PRODUCES CONTROLS OF FUEL INJECTION OPERATION BY THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU) IN RESPONSE TO THE DRIVING CONDITIONS.
*ESA (ELECTRONIC SPARK ADVANCE) SYSTEM
THE ESA SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT TO THE ENGINE CONTROL MODULE
(ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) FROM EACH SENSOR (INPUT SIGNALS FROM (1), (2), (4) TO
(13) ETC.). THE BEST IGNITION TIMING IS DECIDED ACCORDING TO THIS DATA AND THE MEMORIZED DATA IN THE ENGINE
CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) AND THE CONTROL SIGNAL IS OUTPUT
TO TERMINAL IGT. THIS SIGNAL CONTROLS THE IGNITER TO PROVIDE THE BEST IGNITION TIMING FOR THE DRIVING
CONDITIONS.
*HEATED OXYGEN SENSOR HEATER CONTROL SYSTEM (FOR CALIFORNIA)
THE MAIN HEATED OXYGEN SENSOR FRONT AND REAR SIDE, SUB HEATED OXYGEN SENSOR HEATER CONTROL SYSTEM
TURNS THE HEATER ON WHEN THE INTAKE AIR VOLUME IS LOW (TEMP. OF EXHAUST EMISSIONS IS LOW), AND WARMS UP THE
OXYGEN SENSOR TO IMPROVE DETECTION PERFORMANCE OF THE SENSOR. THE ENGINE CONTROL MODULE (ENGINE AND
ELECTRONICALLY CONTROLLED TRANSMISSION ECU) EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM
(1), (2), (4), (9) TO (11) ETC.), AND OUTPUTS CURRENT TO TERMINALS HT1, HT2, HT3 TO CONTROL THE HEATER.
*IDLE AIR CONTROL (IDLE SPEED CONTROL) SYSTEM
THE IDLE AIR CONTROL (ISC) SYSTEM (STEP MOTOR TYPE) INCREASES THE ENGINE SPEED AND PROVIDES IDLING STABILITY
FOR FAST IDLE±UP WHEN THE ENGINE IS COLD, AND WHEN THE IDLE SPEED HAS DROPPED DUE TO ELECTRICAL LOAD AND SO
ON. THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) EVALUATES THE
SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (5), (8), (9), (11) ETC.), OUTPUTS CURRENT TO TERMINALS ISC1,
ISC2, ISC3 AND ISC4 TO CONTROL THE IDLE AIR CONTROL VALVE (ISC VALVE).
*EGR CONTROL SYSTEM
THE EGR CONTROL SYSTEM DETECTS THE SIGNAL FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (9), (10) ETC.), AND
OUTPUTS CURRENT TO TERMINAL EGR TO CONTROL THE EGR VALVE.
*FUEL PUMP CONTROL SYSTEM
THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) OUTPUTS CURRENT TO
TERMINAL FPC AND CONTROLS THE FUEL PUMP ECU AND FUEL PUMP DRIVE SPEED IN RESPONSE TO THE DRIVING
CONDITIONS.
*ACIS (ACOUSTIC CONTROL INDUCTION SYSTEM)
ACIS INCLUDES A VALVE IN THE BULKHEAD SEPARATING THE SURGE TANK INTO TWO PARTS. THIS VALVE IS OPENED AND
CLOSED IN ACCORDANCE WITH THE DRIVING CONDITIONS TO CONTROL THE INTAKE MANIFOLD LENGTH IN TWO STAGES FOR
INCREASED ENGINE OUTPUT IN ALL RANGES FROM LOW TO HIGH SPEEDS.
THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY CONTROLLED TRANSMISSION ECU) JUDGES THE VEHICLE
SPEED BY THE SIGNALS ((4), (5)) FROM EACH SENSOR AND OUTPUTS SIGNALS TO THE TERMINAL ACIS TO CONTROL THE VSV
(FOR INTAKE CONTROL VALVE).
3. DIAGNOSIS SYSTEM
WITH THE DIAGNOSIS SYSTEM, WHEN THERE IS A MALFUNCTION IN THE ENGINE CONTROL MODULE (ENGINE AND
ELECTRONICALLY CONTROLLED TRANSMISSION ECU) SIGNAL SYSTEM, THE MALFUNCTIONING SYSTEM IS RECORDED IN THE
MEMORY. THE MALFUNCTIONING SYSTEM CAN BE FOUND BY READING THE CODE DISPLAYED BY THE MALFUNCTION INDICATOR
LAMP (CHECK ENGINE WARNING LIGHT).
4. FAIL±SAFE SYSTEM
WHEN A MALFUNCTION HAS OCCURRED IN ANY SYSTEM, IF THERE IS A POSSIBILITY OF ENGINE TROUBLE BEING CAUSED BY
CONTINUED CONTROL BASED ON THE SIGNALS FROM THAT SYSTEM, THE FAIL±SAFE SYSTEM EITHER CONTROLS THE SYSTEM
BY USING DATA (STANDARD VALUES) RECORDED IN THE ENGINE CONTROL MODULE (ENGINE AND ELECTRONICALLY
CONTROLLED TRANSMISSION ECU) MEMORY OR ELSE STOPS THE ENGINE.