ECU TOYOTA SUPRA 1986 Service Repair Manual

DIAGNOSTIC TROUBLE CODE CHART
HINT: Parameters listed in the chart may not be exactly the same as your reading due to type of the instruments
or other factors.
DTC
No.
Number of
MIL BlinksCircuitDiagnostic Trouble Code Detecting Condition
Normal
G, NE Signal
(No.1)
G, NE Signal
(No.2)
Ignition Signal
A/T Control
Signal
No code is recorded
No ªNEº or ªG1º and ªG2º signal to ECM for 2 sec. or more after
cranking
No NE signal to ECM for 0.1 sec. or more at 1,000 rpm or
more
NE signal does not pulse 12 times to ECM during the interval
between G1 and G2 pulses
Deviation in G (G1, G2) and NE signal continues for 3 sec. dur-
ing idling (throttle fully closed) after engine warmed up
No IGF signal to ECM for 4~7 consecutive IGT signals with en-
gine speed less than 3,000 rpm
Fault in communications between the engine CPU and A/T CPU
in the ECM
EG±494± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

DTC
No.
Number of
MIL BlinksCircuitDiagnostic Trouble Code Detecting Condition
(a) Engine coolant temp.: 60°C (140°F) or more
(2 trip dectection logic)*3
(2 trip dectection logic)*3
(2 trip dectection logic)*3
EGR gas temp. and intake air temp. are 60°C (140°F) or less
for A/T, 55°C (131°F) or less for 1 ~ 4 min. under conditions
(a) and (b):
Fuel Pump
Control Signal
(2 trip dectection logic)*3
(b) EGR operation possible (Example A/T in 3rd speed (5th for
M/T), A/C ON, 96 km/h (60 mph), Flat road)
Switch Condition
Signal
EGR System
Malfunction
(2) Open in input circuit for 1 sec. or more with engine speed
1,000 rpm or less
(1) Open or short in fuel pump circuit for 1 sec. or more with
engine speed 1,000 rpm or less
(3) Open or short in diagnostic signal line (DI) fuel pump ECU
with engine speed 1,000 rpm or less
(1) 3 sec. or more after engine starts, with closed throttle posi±
tion switch OFF (IDL1)
(2) Park/neutral position switch: OFF
(Shift position in ''R'', ''D'', ''2'', or ''L'' position)
(3) A/C switch ON
*1: ºONº displayed in the diagnostic mode column indicates that the Malfunction Indicator Lamp is lit up when
a malfunction is defected. ºOFFº indicates that the ºCHECKº does not light up during malfunction diag±
nosis, even if a malfunction is detected. ºN.A.º indicates that the item is not included in malfunction diag±
nosis.
*2: ºº in the memory column indicates that a diagnostic trouble code is recorded in the ECM memory when
a malfunction occurs. ºXº indicates that a diagnostic trouble code is not recorded in the ECM memory even
if a malfunction occurs. Accordingly, output of diagnostic results in normal or test mode is done with the
IG switch ON. EG±502
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

Malfunction detection (1st time)
(temporarily recorded)Malfunction detection (2nd time)
(MIL lights up)
 
 
 Trouble Area
 
 
 
Malfunction
Indicator
Lamp*
1
 
 
 Memory*2
 
 
 See page
 
 
Trouble Area
 
 
Normal
Mode 
 
Test
Mode 
 
Memory
 
 
See page
 
 
 
 
 
 

Open in EGR gas temp. sensor circuit

Short in VSV circuit for EGR

EGR hose disconnected, valve stuck

Clogged EGR gas passage

ECM
 
 
 
 
 
 
ON
 
 
 
 
 
 
ON
 
 
 
 
 
 

 
 
 
 
 
 
EG±564
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Open or short in fuel pump ECU circuit

Fuel pump ECU

Fuel pump

ECM power source circuit

ECM
 
 
 
 
 
 
 
 
 
 
 
 
 
 
OFF
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ON
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
EG±568
 
 
 
 
 
 

A/C switch circuit

Throttle position sensor IDL circuit

Park/neutral position switch circuit

Accelerator pedal and cable

ECM
 
 
 
 
 
 
N.A.
 
 
 
 
 
 
OFF
 
 
 
 
 
 
X
 
 
 
 
 
 
EG±571
*3: This indicates items for which º2 trip detection logicº is used. With this logic, when a logic malfunction is
first detected, the malfunction is temporarily stored in the ECM memory. If the same case is detected again
during the second drive test, this second detection causes the Malfunction Indicator Lamp to light up.
The 2 trip repeats the same mode a 2nd time. (However, the IG switch must be turned OFF between the
1st trip and 2nd trip).
In the Test Mode, the Malfunction Indicator Lamp lights up the 1st trip a malfunction is detected.
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±503

FAIL±SAFE CHART
If any of the following codes is detected, the ECM enters fail±safe mode.
 DTC No. Fail±Safe Operation Fail±Safe Deactivation Conditions
 
 14
 
 Fuel cut
 
 6 IGF signals detected in 6 consecutive
ignitions
 16 Torque control prohibited Returned to normal condition 
 22
 
 THW is fixed at 80°C (176°F)
 
 Returned to normal condition
 24 THA is fixed at 20°C (68°F) Returned to normal condition
 
 
 
 
 
 
31
 
 
 
 
 
 
Volume of air flowing is measured by turbo pressure
Sensor to determine injection volume and ignition
Timing
 
 
 
 
 
 
Returned to normal condition
 
 34
 
 Fuel cut
 
 Returned to normal condition
  Turbo  
  
Turbo
Pressure Fuel cut Returned to normal condition
 35 Sensor  
 
 
35
 
 
BARO
Sensor 
 
Atmospheric pressure is fixed at
101.3 kPa (760 mmHg, 29.92 inVHg) 
 Returned to normal condition
 
 
 
 
41
 
 
 
 
VTA1 is fixed at closed throttle position
 
 
 
 
The following must each be repeated at
least 2 times consecutively:

0.1 V
VTA1
0.95 V

IDL: ON
 
 
 
47
 
 
 
VTA2 is fixed at wide open throttle
Position 
 
 
The following must be repeated at least 2
times consecutively

0.1 V
VTA2
0.95 V
 52 Max. timing retardation IG switch OFF
 53 Max. timing retardation Returned to normal condition
 55 Max. timing retardation IG switch OFF
Back±Up Function
If there is trouble with the program in the ECM and the ignition signals (IGT) are not output from the microcomput-
er, the ECM controls fuel injection and ignition timing at predetermined levels as a back±up function to make
it possible to continue to operate the vehicle.
Furthermore, the injection duration is calculated from the starting signal (STA) and the throttle position signal
(IDL). Also, the ignition timing is fixed at the initial ignition timing, 10
°BTDC, without relation to the engine speed.
HINT: If the engine is controlled by the back±up function, the malfunction indicator lamp lights up to warn the
driver of the malfunction but the diagnostic trouble code is not output. EG±504
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

Suspect area
See page
Symptom
Engine does not crank
No initial combustion
No complete combustion
Engine cranks normally
Cold engine
Hot engine
Incorrect first idle
High engine idle speed
Low engine idle speed
Rough idling
Hunting
Hesitation/Poor acceleration
Muffler explosion (after fire)
Surging
Soon after starting
After accelerator pedal depressed
After accelerator pedal released
During A/C operation
When shifting N to D
Does not
start
Difficult to
start
Poor Idling
Engine Stall
Poor
Driveability
Back up power source circuitECM power source circuitPark/neutral position switch circuitSwitch condition signal circuitEGR systemStarter signal circuitMass air flow meter circuitInjector circuitIAC valve circuitFuel pump control circuitA/C signal circuit (Compressor circuit)Turbo control circuitVSV circuit for fuel Pressure ControlCompressionSpark plugIgnition signal circuit (Spark test)Starter and Starter relayIgnition coilEngine control module (ECM)Theft deterrent ECUA/T faulty
EG±544EG±559EG±564EG±571EG±574EG±576EG±581EG±583EG±586EG±568EG±595EG±589AC±62ST±3
,
12
IG±21IG±23IG±22EG±9AT2±101BE±123IN±35
MATRIX CHART OF PROBLEM SYMPTOMS
When the malfunction code is not confirmed in the diagnostic trouble code check and the problem still can not
be confirmed in the basic inspection, proceed to this matrix chart and troubleshoot according to the numbered
order given below. EG±514
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

DTC 14 Ignition Signal Circuit
CIRCUIT DESCRIPTION
The ECM determines the ignition timing, turns on Tr1 at a predetermined angle (°CA) before the desired ignition
timing and outputs an ignition signal (IGT) º1º to the igniter.
Since the width of the IGT signal is constant, the dwell angle control circuit in the igniter determines the time
the control circuit starts primary current flow to the ignition coil based on the engine rpm and ignition timing one
revolution ago, that is, the time the Tr
2 turns on.
When it reaches the ignition timing, the ECM turns Tr
1 off and outputs the IGT signal ºOº.
This turns Tr
2 off, interrupting the primary current flow and generating a high voltage in the secondary coil which
causes the spark plug to spark. Also, by the counter electromotive force generated when the primary current
is interrupted, the igniter sends an ignition confirmation signal (IGF) to the ECM.
The ECM stops fuel injection as a fail safe function when the IGF signal is not input to the ECM.
 DTC No. Diagnostic Trouble Code Detecting Condition Trouble Area 
 
 
 
14
 
 
 
 
No IGF signal to ECM for 4 ~ 7 consecutive
IGT signals with engine speed less than
3,000 rpm
 
 
 
 

Open or short in IGF circuit from igniter to
ECM

Igniter

ECM
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±519

CIRCUIT DESCRIPTION
The throttle position sensor is mounted in the throttle
body and detects the the throttle valve opening angle.
When the throttle valve is fully closed, the IDL contacts
in the throttle position sensor are on, so the voltage at
the terminal IDL of the ECM becomes 0 V. At this time,
a voltage of approximately 0.7 V is applied to the termi-
nal VTA of the ECM. When the throttle valve is opened,
the IDL contacts go off and thus the power source volt-
age of approximately 12 V in the ECM is applied to the
terminal IDL of the ECM. The voltage applied to the ter-
minal VTA of the ECM increases in the proportion to
the opening angle of the throttle valve and becomes
approximately 3.2 ± 4.9 V when the throttle valve is ful-
ly opened. The ECM judges the vehicle driving condi-
tions from these signals input from the terminals VTA
and IDL, and uses them as one of the conditions for de-
ciding the air±fuel ratio correction, power increase
corrections and fuel±cut control etc. The sub±throttle
position sensor is built and operates in the same way
as the main throttle position sensor. This sensor is
used for traction control. The sub±throttle valve is
opened and closed by the sub±throttle actuator ac-
cording to signals from the TRAC ECU to control the
engine output.
Open or short in throttle position sensor circuit
for 0.5 sec. or more
Open or short in sub±throttle position sensor
circuit for 0.5 sec. or more

Open or short in throttle position sensor
circuit

Throttle position sensor

ECM

Open or short in sub±throttle position
sensor circuit

Sub±throttle position sensor

ECM
HINT:
Diagnostic trouble code 41 is for the throttle position sensor circuit.
Diagnostic trouble code 47 is for the sub±throttle position sensor circuit.

When the connector for the throttle position sensor(s) is disconnected, diagnostic trouble code 41
or 47 is not displayed. Diagnostic trouble code 41 or 47 is displayed only when there is an open
or short in the VTA signal circuit of the throttle position sensor(s).

Signals from the throttle position sensor(s) are also input to the TRAC ECU, so when a malfunc±
tion occurs on the TRAC side, code 41 or 47 may be displayed.
DTC 41 47 Throttle Position Sensor(s) Circuit
EG±552± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

INSPECTION PROCEDURE
(See page EG±510)
(1) Shift the shift lever to N position.
(2) Jack up one of the rear wheels.
(3) Connect SST (check harness ªAº).
(See page
EG±510)
(4) Disconnect power steering ECU connector
and cruise control ECU connector.
(5) Turn ignition switch ON.
Measure voltage between terminal SP1 of engine
control module connector and body ground when
the wheel is turned slowly.
Voltage is generated intermittently.
Check voltage between terminal SP1 of engine control module connector
and body ground.
Check and replace engine control module.
Repair or replace harness or connector between
ECM and telltale light RH.
Repair or replace harness or connector between
telltale light RH and No.1 vehicle speed sensor.
Replace No.1 vehicle speed sensor.
Check operation of odometer and trip meter (telltale light RH
(See page Be±48)).
Check operation of No.1 vehicle speed sensor (See page BE±46).
EG±558± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

DTC 78 Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
The fuel pump speed is controlled at 2 steps (high speed, low speed) by the condition of the engine (starting,
light load, heavy load), when the engine starts (STA ON), the engine control module sends a Hi signal (battery
positive voltage) to the fuel pump ECU (FPC terminal).
The fuel pump ECU then outputs Hi voltage (battery positive voltage) to the fuel pump so that the fuel pump
operates at high speed.
After the engine starts, during idling or light loads, the engine control module outputs a Low signal (about 9 V)
to the fuel pump ECU, the fuel pump ECU outputs Low battery voltage (about 9 V) to the fuel pump and causes
the fuel pump to operate at low speed.
If the intake air volume increases (high engine load), the engine control module sends a Hi signal to the fuel
pump ECU and causes the fuel pump to operate at high speed.
 
 DTC No.
 
 Diagnostic Trouble Code Detecting Condition
 
 Trouble Area
 
 
 
 
 
 
 
 
(1) Open or short in fuel pump circuit for
1 sec. Or more with engine speed
1,000 rpm or less
(2 trip detection logic)* 
 
 
 O h t i f l ECU i it 
 
 
78
 
 
 
(2) Open in input circuit of fuel pump ECU
(FPC) with engine speed 1,000 rpm or
less
(2 trip detection logic)* 
 
 

Open or short in fuel pump ECU circuit

Fuel pump ECU

Engine control module power source circuit

Fuel pump

Engine control module 
 
 
 
 
 
 
 
(3) Open or short in diagnostic signal line (DI)
of fuel pump ECU with engine speed
1,000 rpm or less
(2 trip detection logic)*
 
 
 
 

Engine control module
*: See page EG±503. EG±568
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

(See page IN±30).
Check for ECM power source circuit (See page
EG±576), and check for open in harness and
connector between terminal +B of data link
connector 1 and main relay.
(1) Turn ignition switch ON.
(2) Using SST, connect terminals +B and FP of data
link connector 1.
SST 09843±18020
Check that there is pressure in the hose from the fuel
filter.
Fuel pressure can be felt.
Check fuel pump operation.
Repair or replace harness or connector.
Check for open and short in harness and connector between terminals
+B
+B, FP
FP of the data link connector 1 and fuel pump ECU (See
page IN±30).
Turn ignition switch ON.
Measure voltage between terminal +B of data link con-
nector 1 and body ground.
Voltage: 9 Ð 14 V
Check voltage of terminal +B of data link connector 1.
Check for ECM power source circuit (See
page EG±576), and check for open in harness
and connector between terminal +B of data
link connector 1 and main relay.
INSPECTION PROCEDURE
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±569