sensor TOYOTA SUPRA 1995 Service Repair Manual

  TACHOMETER (ON±VEHICLE) 
 Standard indication (rpm) Allowable range (rpm)
 700 630 ± 770
 1000 915 ± 1115
 2000 1920 ± 2220
 3000 2890 ± 3350
 4000 3940 ± 4400
50005025 ± 5425 
6500
 
6650 ± 6950 
7000
 
7025 ± 7625  OD/TRIP METER (CONNECTOR CONNECTED) 
  1 ± Ground (Ignition SW position ON) Battery positive voltage  4 ± Ground (Light Control SW position TAIL or HEAD) Battery positive voltage  5 ± 7 (Ignition SW ON and drive the vehicle slowly) OV eBattery positive voltage  6 ± 7 (Ignition SW ON and drive the vehicle slowly) OV emore than 5V  8 ± Ground (Constant) Battery positive voltage 
 
 
10 ± Ground (Ignition SW ON, Light Control SW TAIL or
HEAD and turn the Light Control Rheostat
knob to clockwise) 
 
 6V " 0V
  FUEL RECEIVER GAUGE 
 A ± B Approx. 269.7

 A ± C Approx. 123.5

 B ± C Approx. 146.2

  FUEL SENDER GAUGE 
  Float position: F Approx. 4.0

  Float position: 1/2 Approx. 55.0

  Float position: E Approx. 107.0

  ENGINE COOLANT TEMPERATURE RECEIVER GAUGE 
 A ± B Approx. 229.7

 A ± C Approx. 54.0

 B ± C Approx. 175.7

  ENGINE COOLANT TEMPERATURE SENDER GAUGE 
  50 °C (122.0 °F) 160 ± 240

  120 °C (248.0 °F) 17.1 ± 21.2

  LIGHT FAILURE SENSOR 
  3 ± Ground (Light Control SW position OFF) No voltage
  3 ± Ground (Light Control SW position TAIL or HEAD) Battery positive voltage
  4 ± Ground (Ignition SW position LOCK or ACC) No voltage
  4 ± Ground (Ignition SW position ON) Battery positive voltage
  7 ± Ground (Stop Light SW position OFF) No voltage
  7 ± Ground (Stop Light SW position ON) Battery positive voltage
 8 ± Ground (Engine stop)No voltage 
8 ± Ground (Engine running)
 
Battery positive voltage 
INTEGRATION RELAY (Seat Belt Warning)
 
  1 ± Ground (Constant) Battery positive voltage  9 ± Ground (Ignition SW LOCK or ACC) No voltage  9 ± Ground (Ignition SW ON) Battery positive voltage
BE±202± BODY ELECTRICAL SYSTEMSERVICE SPECIFICATIONS

SRS (Supplemental Restraint System)
The 1995 SUPRA is equipped with an SRS, such as the driver airbag and front passenger airbag assembly.
Failure to carry out service operations in the correct sequence could cause the SRS to deploy, possibly
leading to a serious accident.
When removing or installing of airbag parts and the yellow wire harness and connector for the airbag is
necessary, refer to the precautionary notices in the RS section before performing the operation.
wWork must be started after 90 seconds from the time the ignition switch is set to the LOCK position
and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source so that if work is started within 90 seconds of
disconnecting the negative (±) terminal cable of the battery, the SRS may deploy.)
wTo avoid erasing the memory of each memory system, never use a back±up power supply from
outside the vehicle.
wBefore repairs, remove the airbag sensors if shocks are likely to be applied to the sensors during
repairs.
wThe front airbag sensor set bolt has been anti±rust treated. When the sensor is removed, always
replace the set bolt with a new one.
wIf the front airbag sensors, center airbag sensor assembly, steering wheel pad or front passenger
airbag assembly have been dropped, or if there are cracks, dents or other defects in the case, bracket
or connector, replace them with new ones.
wNever use SRS parts from another vehicle. When replacing parts, replace them with new parts.
wDo not expose the front airbag sensors, center airbag sensor assembly, steering wheel pad or front
passenger airbag assembly directly to hot air or flames.
wThe SRS wire harness is integrated with the cowl wire harness assembly. The wires for the SRS wire
harness are encased in a yellow corrugated tube. All the connectors for the system are also a standard
yellow color. If the SRS wire harness becomes disconnected or the connector becomes broken due
to an accident, etc., repair or replace it. (See RS section)
wThe steering wheel must be fitted correctly to the steering column with the spiral cable at the neutral
position; otherwise, cable disconnection and other troubles may result. Refer to RS section of this
manual concerning correct steering wheel installation.
wWhen removing or handling the steering wheel pad or front passenger airbag assembly, it should be
placed with their top surface facing up. In this case, the twin±lock type connector lock lever should
be in the locked state and care should be taken to place it so the connector will not be damaged.
(Storing the pad with its metallic surface up, the front passenger airbag assembly with the airbag door
facing down may lead to a serious accident if the airbag inflates for some reason.)
wGrease should not be applied to the steering wheel pad or the front passenger airbag assembly, and
they should not be cleaned with detergents of any kind.
wStore the steering wheel pad or the front passenger airbag assembly where the ambient temperature
remains below 93°C (200°F), without high humidity and away from electrical noise.
wInformation labels are attached to the periphery of the SRS components. Follow the notices.
wWhen the ignition switch is at ACC or ON and the SRS warning light remains on, the center airbag
sensor assembly has detected a malfunction code. (See RS section)
± BODYGENERAL INFORMATIONBO±5

INSTRUMENT PANEL DISASSEMBLY
1. REMOVE THESE PARTS FROM INSTRUMENT PANEL
(a) Defroster nozzle garnish
(b) Defroster nozzle
(c) Solar sensor
(d) Speakers
(e) Side defroster No.1 nozzle
(f) No.1 bracket
(g) Heater to register No.5 duct
(h) No.4 register
(i) Heater to register No.1 duct
(j) No.3 register
(k) Striker plate
(l) Instrument panel box light switch
(m) Room temperature sensor
(n) Theft deterrent and door lock ECU
(o) Power steering computer
(p) Audio mounting No.1 and No.2 bracket
(q) No.2 and No.3 bracket
(r) No.1 pins
2. REMOVE INSTRUMENT PANEL WIRE HARNESS
INSTRUMENT PANEL ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTRUMENT PANEL INSTALLATION
Installation is in the reverse order of removal.
± BODYINSTRUMENT PANELBO±51

FRONT SPEED SENSOR
COMPONENTS
FRONT SPEED SENSOR REMOVAL
Installation is in the reverse order of removal.
AFTER INSTALLATION, CHECK SPEED SENSOR SIG-
NAL (See page BR±62)
1. DISCONNECT CONNECTOR
(a) Remove the front fender splash shield.
(b) Disconnect the speed sensor connector.
2. REMOVE SPEED SENSOR
(a) Remove the 3 clamp bolts holding the sensor harness to the
body and upper suspension arm.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
(b) Remove the speed sensor from the steering knuckle.
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
(c) Remove the O±ring from the speed sensor. BR±48
± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)

REAR SPEED SENSOR
COMPONENTS
REAR SPEED SENSOR REMOVAL
Installation is in the reverse order of removal.
AFTER INSTALLATION, CHECK SPEED SENSOR SIG-
NAL (See page BR±62)
1. DISCONNECT SPEED SENSOR CONNECTOR
(a) Remove the rear seat cushion and seat back.
(b) Remove the quarter trim panel.
(c) Disconnect the speed sensor connector, and pull out the
sensor wire harness with the grommet.
2. REMOVE SPEED SENSOR
(a) Remove the 2 clamp bolts holding the sensor wire harness
to the body and upper arm.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
(b) Remove the speed sensor from the axle carrier.
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)BR±49

P. BR±84
P. BR±86 ~ BR±89
P. BR±24
P. BR±86
P. BR±88P. BR±92
P. BR±104 ~ BR±165P. BR±166
Vehicle brought to workshop
Perform troubleshooting in accordance with the procedure on the following pages.
Items insideare titles of pages in this manual,
with the page number in the bottom portion. See the pages
for detailed explanations.
Customer Problem Analysis
Check and Clear Diagnostic Trouble Codes (Precheck)
Symptom
does not occur
Problem Symptom ConfirmationSymptom Simulation
Symptom
occurs
Diagnostic Trouble Code CheckNormal code
Malfunction code
Diagnostic Trouble Code ChartProblem Symptoms Chart
Circuit InspectionSensor CheckCheck for Fluid Leakage
Identification of Problem
Repair
Confirmation Test
EndStepDiagnostic steps permitting the use of the TOYOTA
hand±held tester or TOYOTA break±out box.
HOW TO PROCEED WITH TROUBLESHOOTING
BR±52± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)

DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the diagnostic trouble code check, check the circuit listed for that
code in the table below and proceed to the relevant page.
HINT: Using SST 09843±18020, connect the terminals Tc and E
1, and remove the short pin.
BR±65
BR±65
BR±71
BR±71
BR±77
BR±77
BR±80
BR±80
BR±83
BR±83
BR±83
BR±83
BR±86
BR±86
BR±88
BR±88
BR±88
BR±88
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF*
OFF*
CodeABS Warning Light
Blinking PatternIndicator
DiagnosisSee pageABS
Warning
LightTRAC
OFF
LightTRAC
Indicator
Light
Open or short in ABS solenoid relay circuit
B+ short in ABS solenoid relay circuit
Open or short in ABS motor relay circuit
B+ short in ABS motor relay circuit
Open or short in TRAC solenoid relay circuit
B+ short in TRAC solenoid relay circuit
Open or short in TRAC motor relay circuit
B+ short in TRAC motor relay circuit
Open or short in ABS actuator solenoid circuit
(SFR circuit)
Open or short in ABS actuator solenoid circuit
(SFL circuit)
Open or short in ABS actuator solenoid circuit
(SRR circuit)
Open or short in ABS actuator solenoid circuit
(SRL circuit)
Open or short in TRAC actuator solenoid circuit
(SMC circuit)
Open or short in TRAC actuator solenoid circuit
(SRC circuit)
Right front wheel speed sensor signal
malfunction
Left front wheel speed sensor signal
malfunction
Right rear wheel speed sensor signal
malfunction
Left rear wheel speed sensor signal
malfunction
BR±56± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)

BR±88.
BR±88
BR±92
BR±95
BR±97
BR±98
BR±100
BR±102
BR±104
CodeABS Warning Light
Blinking Pattern
Indicator
DiagnosisSee pageABS
Warning
LightTRAC
Indicator
LightTRAC
OFF
Light
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF*
OFF*
OFF*
OFF*
Always
ON
Open circuit in left front or right rear speed sensor
circuit
Open circuit in right front or left rear speed sensor
circuit
Low battery positive voltage or abnormally high
battery positive voltage
Open or short in lateral acceleration
sensor circuit
ABS pump motor is locked
Open in ABS pump motor ground
Brake fluid reservoir level low
Open circuit in TRAC pump motor circuit
TRAC ECU communication abnormal
Wheel speed sensor signal malfunction
Malfunction in ABS (& TRAC) ECU

: Only vehicles with TRAC
*: When a malfunction causing code No. 17, 18, 55, 58, 61 or 62 is detected, the ABS warning light does
not light up, but the TRAC indicator light does. However, when checking the DTC, check the blinking
pattern of the ABS warning light.
± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)BR±57

SPEED SENSOR SIGNAL CHECK
1. Turn the ignition switch OFF
2. Using SST, connect terminals Ts and E1 of DLC1.
SST 09843±18020
3. Start the engine.
4. Check that the ABS warning light blinks.
HINT:
wIf the ABS warning light does not blink, inspect the ABS
warning light circuit (See page BR±107).
wIf the ABS warning light is always on, inspect and repair
the IG1 terminal of lateral acceleration sensor.
5. Drive the vehicle faster than 45 km/h (28 mph) for several
seconds.
6. Stop the vehicle.
7. Using SST, connect terminals Tc and E1 of DLC1.
SST 09843±18020
8. Read the number of blinks of the ABS warning light.
HINT: See the list of diagnostic trouble codes shown on the
next page.
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunctions are indicated at the same time, the
lowest numbered code will be displayed first.
9. After doing the check, disconnect terminals Ts and E1, Tc and
E1 of DLC1, and turn ignition switch OFF. BR±62
± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)

ECU DATA MONITOR USING TOYOTA
HAND±HELD TESTER
1. Hook up the TOYOTA hand±held tester to the DLC2.
2. Monitor the ECU data by following the prompts on the tester
screen.
HINT: TOYOTA hand±held tester has a ºSnapshotº function
which records the monitored data.
Please refer to the TOYOTA hand±held tester operator's
manual for further details.
Diagnostic Trouble Code of Speed Sensor Check Function
 Code No. Diagnosis Trouble Area
 
 71
 
 Low output voltage of right front speed sensor
 
 

Right front speed sensor

Sensor installation
 
 72
 
 Low output voltage of left front speed sensor
 
 

Left front speed sensor

Sensor installation
 
 73
 
 Low output voltage of right rear speed sensor
 
 

Right rear speed sensor

Sensor installation
 
 74
 
 Low output voltage of left rear speed sensor
 
 

Left rear speed sensor

Sensor installation
 
 75
 
 
Abnormal change in output voltage of right front speed
sensor 
 
Right front speed sensor rotor
 
 76
 
 
Abnormal change in output voltage of left front speed
sensor 
 
Left front speed sensor rotor
 
 77
 
 
Abnormal change in output voltage of right rear speed
sensor 
 
Right rear speed sensor rotor
 
 78
 
 
Abnormal change in output voltage of left rear speed
sensor 
 
Left rear speed sensor rotor
± BRAKE SYSTEMANTI±LOCK BRAKE SYSTEM (ABS)BR±63