battery location TOYOTA SUPRA 1997 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1997, Model line: SUPRA, Model: TOYOTA SUPRA 1997Pages: 1807, PDF Size: 39.36 MB
Page 374 of 1807
Steering Wheel Pad
(with Airbag) Junction Block No. 1Center Airbag Sensor Assembly Front Airbag Sensor LHFront Passenger Airbag Assembly Front Airbag Sensor RHSRS Warning Light
Spiral Cable
Locations of SRS Components
HANDLING PRECAUTIONS ON RELATED COMPONENTS
1. SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
Servicing vehicle with a Supplemental Restraint System (referrerd to as the SRS in the remainder of this
manual) installed.
When handling SRS components (removal, installation or inspection, etc.), always follow the directions
given in the repair manual for the relevant model year to prevent the occurrence of accidents and airbag
malfunction.
Also take the following precautions when repairing the body:
Work must be started after 90 seconds or longer from the time the ignition switch is set to the LOCK
position and the negative (-) terminal cable is disconnected from the battery.
(The airbag system is equipped with a backup power source so that if work is started within 20 seconds
of disconnecting the negative (-) terminal cable of the battery, the airbag may be deployed.)
When the negative (-) terminal cable is disconnected from the battery, memory of the clock and audio
systems will be cancelled. So before starting work, make a record of the contents memorized by each
memory system. Then when work is finished, reset the clock and audio systems as before.
When the vehicle has tilt and telescopic steering, power seat, outside rear view mirror and power shoul-
der belt anchorage, which are all equipped with memory function, it is not possible to make a record of
the memory contents. So when the operation is finished, it will be necessary to explain this fact to the
customer, and request the customer to adjust the features and reset the memory.
When using electric welding, first disconnect the SRS connector (yellow color and 2 pins) under the
steering column near the combination switch connector on the glove compartment finish plate and lower
the front scuff plate before starting work.
INTRODUCTIONIN-6
Page 377 of 1807
Light Failure Sensor Fuel Pump ECURear Wiper Relay
5. COMPONENTS ADJACENT TO THE BODY PANELS Locations of ECUs (Cont'd)
Many ECUs are mounted in this vehicle.
Take the following precautions during body repair to prevent damage to the ECUs.
Before starting electric welding operations, disconnect the negative (-) terminal cable from the battery.
When the negative (-) terminal cable is disconnected from the battery, memory of the clock and audio
systems will be cancelled. So before starting work, make a record of the contents memorized by each
memory system. Then when work is finished, reset the clock and audio systems as before.
When the vehicle has tilt and telescopic steering, power seat and outside rear view mirror, which are all
equipped with memory function, it is not possible to make a record of the memory contents.
So when the operation is finished, it will be necessary to explain this fact to the customer, and request
the customer to adjust the features and reset the memory.
Do not expose the ECUs to ambient temperatures above 80°C (176°F).
NOTICE: if it is possible the ambient temperature may reach 80°C (176°F) or more, remove the ECUs
from the vehicle before starting work.
Be careful not to drop the ECUs and not to apply physical shocks to them.
Various types of component parts are mounted directly on or adjacently to the body panels.
Strictly observe the following precautions to prevent damaging these components and the body panels
during handling.
Before repairing the body panels, remove their components or apply protective covers over the
components.
Before prying components off using screwdriver or a scraper, etc., attach protective tape to the tool
tip or blade to prevent damaging the components an the body paint.
Before removing components from the outer surface of the body, attach protective tape to the body
to ensure no damage to painted areas.
HINT: Apply touch-up paint to any damaged paint surfaces.
Before drilling or cutting sections, make sure that there are no wires, etc. on the reverse side.
INTRODUCTIONIN-9
Page 567 of 1807
DI-152
- DIAGNOSTICSENGINE (2JZ-GTE)
380 Author: Date:
1997 SUPRA (RM502U)
6. BASIC INSPECTION
When the malfunction code is not confirmed in the DTC check, troubleshooting should be performed in the
order for all possible circuits to be considered as the causes of the problems.
In many causes, by carrying out the basic engine check shown in the following flow chart, the location caus-
ing the problem can be found quickly and efficiently. Therefore, use of this check is essential in engine trou-
bleshooting.
1 Is battery positive voltage 11 V or more when engine is stopped?
NO Charge or replace battery.
YES
2 Is engine cranked?
NO Proceed to page ST-14, ST-16 and continue to
troubleshoot.
YES
3 Does engine start?
NO Go to step 7.
YES
Page 1002 of 1807
3
HOW TO USE THIS MANUAL B
This manual provides information on the electrical circuits installed on vehicles
by dividing them into a circuit for each system.
The actual wiring of each system circuit is shown from the point where the power
source is received from the battery as far as each ground point. (All circuit
diagrams are shown with the switches in the OFF position.)
When troubleshooting any problem, first understand the operation of the circuit
where the problem was detected (see System Circuit section), the power source
supplying power to that circuit (see Power Source section), and the ground
points (see Ground Points section). See the System Outline to understand the
circuit operation.
When the circuit operation is understood, begin troubleshooting of the problem
circuit to isolate the cause. Use Relay Location and Electrical Wiring Routing
sections to find each part, junction block and wiring harness connectors, wiring
harness and wiring harness connectors, splice points, and ground points of each
system circuit. Internal wiring for each junction block is also provided for better
understanding of connection within a junction block.
Wiring related to each system is indicated in each system circuit by arrows
(from
,to ). When overall connections are required, see the Overall Electrical
Wiring Diagram at the end of this manual.
Page 1050 of 1807
44
H POWER SOURCE (Current Flow Chart)
The chart below shows the route by which current flows from the battery to each electrical source
(Fusible Link, Circuit Breaker, Fuse, etc.) and other parts.
The next page and following pages show the parts to which each electrical source outputs current.
[LOCATION]1: J/B No. 1 (See page 20) 2: R/B No.2 (See page 22)
Page 1063 of 1807
58
POWER SOURCE
HEADLIGHT RELAY (USA)
2-1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION OR THE DIMMER SW AT FLASH POSITION
HEADLIGHT RELAY (CANADA)
2-1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION OR THE DIMMER SW AT FLASH POSITION
: CLOSED WITH THE ENGINE RUNNING AND THE PARKING BRAKE LEVER RELEASED (PARKING BRAKE SW
OFF)
TAILLIGHT RELAY
5-3 : CLOSED WITH THE LIGHT CONTROL SW AT TAIL OR HEAD POSITION
I19 IGNITION SW
2-3 : CLOSED WITH THE IGNITION KEY AT ACC OR ON POSITION
2-4 : CLOSED WITH THE IGNITION KEY AT ON OR ST POSITION
7-6 : CLOSED WITH THE IGNITION KEY AT ON OR ST POSITION
7-8 : CLOSED WITH THE IGNITION KEY AT ST POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
I1929
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
222R/B NO.2 (ENGINE COMPARTMENT LEFT)
423R/B NO.4 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1C20FLOOR NO. 2 WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1H
1J20COWL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1K
()
2A22BATTERY AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2B22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IB136ENGINE ROOM MAIN WIRE AND COWL WIRE (LEFT KICK PANEL)
IC236FLOOR NO. 2 WIRE AND COWL WIRE (LEFT KICK PANEL)
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E732ENGINE ROOM MAIN WIREE2034ENGINE ROOM MAIN WIRE
I1 9
X234
X678
SERVICE HINTS
Page 1067 of 1807
62
STARTING AND IGNITION (2JZ-GTE)
I19 IGNITION SW
7-8 : CLOSED WITH THE IGNITION SW AT ST POSITION
7-6 : CLOSED WITH THE IGNITION SW AT ON OR ST POSITION
P2 PARK/NEUTRAL POSITION SW (A/T)
6-5 : CLOSED WITH THE A/T SHIFT LEVER IN P OR N POSITION
C9 CLUTCH START SW (M/T)
1-2 : CLOSED WITH THE CLUTCH PEDAL FULLY DEPRESSED
S2 (A), S3 (B) STARTER
POINTS CLOSED WITH THE PARK/NEUTRAL POSITION SW ON AND THE IGNITION SW AT ST POSITION (A/T)
POINTS CLOSED WITH THE CLUTCH START SW ON AND THE IGNITION SW AT ST POSITION (M/T)
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C124I3B25J229
C224I625N125 (2JZ-GTE)
C324 (2JZ-GTE)I725P225 (2JZ-GTE)
C928I825S2A25 (2JZ-GTE)
D124 (2JZ-GTE)I925S3B25 (2JZ-GTE)
E9B29I1025T1329
E10A29I1125
I2A25I1929
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
222R/B NO. 2 ( ENGINE COMPARTMENT LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1J20COWL WIRE AND J/B NO 1 (LEFT KICK PANEL)IK20COWL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
2A22BATTERY AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EA132(2JZ-GTE)ENGINE WIRE AND ENGINE ROOM MAIN WIRE (NEAR THE R/B NO 2)EA232ENGINE WIRE AND ENGINE ROOM MAIN WIRE (NEAR THE R/B NO. 2)
IB136ENGINE ROOM MAIN WIRE AND COWL WIRE (LEFT KICK PANEL)IB236ENGINE ROOM MAIN WIRE AND COWL WIRE (LEFT KICK PANEL)
IF236INSTRUMENT PANEL WIRE AND COWL WIRE (INSTRUMENT PANEL REINFORCEMENT LH)
II138ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
IJ138ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)IJ238ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC32 (2JZ-GTE)FRONT SIDE OF INTAKE MANIFOLD
ED32 (2JZ-GTE)REAR SIDE OF INTAKE MANIFOLD
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E11I4
E1632ENGINE WIREI1738COWL WIRE
E17I20
SERVICE HINTS
Page 1070 of 1807
69
G2 (A) GENERATOR
(A) 3-GROUND :13.9-15.1 VOLTS WITH THE ENGINE RUNNING AT 2000 RPM AND 25C (77F)
13.5-14.3 VOLTS WITH THE ENGINE RUNNING AT 5000 RPM AND 115C (239F)
(A) 1-GROUND ;0-4 VOLTS WITH THE IGNITION SW AT ON POSITION AND THE ENGINE NOT RUNNING
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
G1B24 (2JZ-GTE)G2A24 (2JZ-GTE)T629G1B26 (2JZ-GE)G2A26 (2JZ-GE)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
222R/B NO. 2 (ENGINE COMPARTMENT LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1E20INSTRUMENT PANEL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
2A22BATTERY AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EA232ENGINE WIRE AND ENGINE ROOM MAIN WIRE (NEAR THE R/B NO 2)EA334ENGINE WIRE AND ENGINE ROOM MAIN WIRE (NEAR THE R/B NO. 2)
II138ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I1438INSTRUMENT PANEL WIRE
1
123 B
G 1ABLACK
12 X X X3T 6 G 2
SERVICE HINTS
Page 1080 of 1807
79
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A524 (2JZ-GTE)H524S125
C124H1129S525
C224I125 (2JZ-GTE)S1129
C324 (2JZ-GTE)I2B25T225 (2JZ-GTE)
C928I3A25T529
C10A28I1225 (2JZ-GTE)T629
C12B28I1325 (2JZ-GTE)T1425
D124 (2JZ-GTE)I1425 (2JZ-GTE)T1529
D528I1525 (2JZ-GTE)V225 (2JZ-GTE)
D828I1625 (2JZ-GTE)V325 (2JZ-GTE)
D1728I1725 (2JZ-GTE)V425
E124 (2JZ-GTE)I1929V525
E324 (2JZ-GTE)J229V625 (2JZ-GTE)
E9B29K125 (2JZ-GTE)V725
E10A29K225 (2JZ-GTE)V825
F1430M125V1025 (2JZ-GTE)
F1530P225 (2JZ-GTE)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
222R/B NO. 2 (ENGINE COMPARTMENT LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C20FLOOR NO. 2 WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1E20INSTRUMENT PANEL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1H
1I20COWL WIRE AND J/B NO 1 (LEFT KICK PANEL)1J20COWL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1K
2A22BATTERY AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EA132 (2JZ-GTE)ENGINE WIRE AND ENGINE ROOM MAIN WIRE (NEAR THE R/B NO 2)EA232ENGINE WIRE AND ENGINE ROOM MAIN WIRE (NEAR THE R/B NO. 2)
IB136ENGINE ROOM MAIN WIRE AND COWL WIRE (LEFT KICK PANEL)
IC136FLOOR NO 2 WIRE AND COWL WIRE (LEFT KICK PANEL)IC236FLOOR NO. 2 WIRE AND COWL WIRE (LEFT KICK PANEL)
IF136INSTRUMENT PANEL WIRE AND COWL WIRE (INSTRUMENT PANEL REINFORCEMENT LH)
II138ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
IJ138ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)IJ238ENGINE WIRE AND COWL WIRE (RIGHT KICK PANEL)
BP140FUEL GAUGE WIRE AND FLOOR NO. 2 WIRE (LUGGAGE ROOM FRONT LH)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB32 (2JZ-GTE)FRONT SIDE OF LEFT FENDER
ED32 (2JZ-GTE)REAR SIDE OF INTAKE MANIFOLD
IE36LEFT KICK PANELIF36LEFT KICK PANEL
IG36RIGHT KICK PANEL
BI40LEFT QUARTER PILLAR
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E732ENGINE ROOM MAIN WIREI238COWL WIRE
E10I438INSTRUMENT PANEL WIRE
E11I538INSTRUMENT PANEL WIREE12I838INSTRUMENT PANEL WIRE
E1332ENGINE WIREI1138COWL WIRE
E14
32ENGINE WIRE
I1438INSTRUMENT PANEL WIRE
E16I1738ENGINE WIRE
E17I2038COWL WIRE
Page 1084 of 1807
![TOYOTA SUPRA 1997 Service Repair Manual 95
HEADLIGHT RELAY
2-1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION OR THE DIMMER SW AT FLASH POSITION
C13 LIGHT CONTROL SW [COMB. SW]
13-1 1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION](/img/14/57469/w960_57469-1083.png "TOYOTA SUPRA 1997 Service Repair Manual 95
HEADLIGHT RELAY
2-1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION OR THE DIMMER SW AT FLASH POSITION
C13 LIGHT CONTROL SW [COMB. SW]
13-1 1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION")
95
HEADLIGHT RELAY
2-1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION OR THE DIMMER SW AT FLASH POSITION
C13 LIGHT CONTROL SW [COMB. SW]
13-1 1 : CLOSED WITH THE LIGHT CONTROL SW AT HEAD POSITION
C13 LIGHT CONTROL SW [COMB. SW]
14-9 : CLOSED WITH THE DIMMER SW AT FLASH POSITION
12-9 : CLOSED WITH THE DIMMER SW AT HIGH OR FLASH POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1228H224 (2JZ-GTE)H424 (2JZ-GTE)
C1328H227 (2JZ-GE)H427 (2JZ-GE)
H124 (2JZ-GTE)H324 (2JZ-GTE)I2029H127 (2JZ-GE)H327 (2JZ-GE)
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
222R/B NO.2 (ENGINE COMPARTMENT LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1J20COWL WIRE AND J/B NO 1 (LEFT KICK PANEL)1K20COWL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
2A22BATTERY AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IB136ENGINE ROOM MAIN WIRE AND COWL WIRE (LEFT KICK PANEL)IB236ENGINE ROOM MAIN WIRE AND COWL WIRE (LEFT KICK PANEL)
IF136INSTRUMENT PANEL WIRE AND COWL WIRE (INSTRUMENT PANEL REINFORCEMENT LH)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA32 (2JZ-GTE)FRONT SIDE OF RIGHT FENDEREA34 (2JZ-GE)FRONT SIDE OF RIGHT FENDER
IE36LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E232E2134ENGINE ROOM MAIN WIRE
E932ENGINE ROOM MAIN WIREI238COWL WIRE
E1834
X 3 2XX
9
1112 13 1412 12
12 12C12 C13 H 1 H 2
H 3H 4 I20BLACK BLACK BLACK
BROWN BROWN
34
SERVICE HINTS