lock TOYOTA T100 1996 Factory User Guide

Downloaded from www.Manualslib.com manuals search engine V08423 Knock Sensor 1
GRECM
KNK
E1 12
E6
WIRING DIAGRAM
 Wiring Diagram
DTC P0325Knock Sensor 1 Circuit Malfunction
CIRCUIT DESCRIPTION
Knock sensor is fitted to the cylinder block to detect engine knocking. This sensor contains a piezoelectric element which
generates a voltage when it becomes deformed, which occurs when the cylinder block vibrates due to knocking. If engine
knocking occurs, ignition timing is retarded to suppress it.
DTC No. DTC Detecting Condition Trouble Area
P0325No knock sensor 1 signal to ECM with engine speed,
1,200 rpm or more. Open or short in knock sensor1 circuit
 Knock sensor 1 (looseness)
 ECM
If the ECM detects the above diagnosis conditions, it operates the fall safe function in which the corrective retard angle
value is set to the maximum value.
 Diagnostic Trouble Code No. and Detection Item
 Circuit Description
The major role and operation, etc. of the circuit
and its component parts are explained.
 Indicates the diagnostic trouble code, diagnostic
trouble code set parameter and suspect area of
the problem.
This shows a wring diagram of the circuit.
Use the diagram together with ELECTRICAL
WIRING DIAGRAM to thoroughly understand the
circuit.
Wiring colors are indicated by an alphabetical code.
B = Black, L = Blue, R = Red, BR = Brown,
LG = Light Green, V = Violet, G = Green,
O = Orange, W = White, GR = Gray, P = Pink,
Y = Yellow
The first letter indicates the basic wire color and
the second letter indicates the color of the stripe. IN−24
− INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
1996 TOYOTA T100 (RM449U)
6. CIRCUIT INSPECTION
How to read and use each page is shown below.

Downloaded from www.Manualslib.com manuals search engine V08425
LOCK
KNK
E6 Connector
(a) Remove the glove compartment (See page SF − 37).
(b) Disconnect the E6 connector of ECM.
INSPECTION PROCEDURE
Replace knock sensor. 1 Check continuity between terminal KNK of ECM connector and body ground.
OK:
Check knock sensor (See page SF − 34). Measure resistance between terminal KNK of ECM connector
and body ground.
Resistance: 1 MΩ or higher
Connector being checked is connected.  Indicates the condition of the connector of ECU during the check.
PREPARATION:
CHECK:
2Go to step 3.
OK OK
NG
 Indicates the position of the ignition switch during the check.
Check from the connector back side.
(with harness)
Ignition Switch LOCK (OFF)
Ignition Switch START
LOCKIgnition Switch ON
Ignition Switch ACC
STARTON
ACC
 Inspection Procedure
 Indicates the place to check the voltage or resistance.
 Indicates the connector position to checked, from the front or back side.
Connector being checked is disconnected. Check from the connector front side. (without harness)
In this case, care must be taken not to bend the terminals.
E6 Connector KNKWire Harness
E6 Connector KNK
A00255 AB0117
A00265
Use the inspection procedure to determine
if the circuit is normal or abnormal, and, if
it is abnormal, use it to determine whether
the problem is located in the sensors,
actuators, wire harness or ECU.
− INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN−25
1996 TOYOTA T100 (RM449U)

Downloaded from www.Manualslib.com manuals search engine IN0379
Sensor Side
ECU Side
IN0378
Sensor SideECU Side
IN0380
Sensor SideECU Side
IN0381
Pull Lightly
Looseness of Crimping
− INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN−27
1996 TOYOTA T100 (RM449U)
2. CONTINUITY CHECK (OPEN CIRCUIT CHECK)
(a) Disconnect the connectors at both ECU and sensor
sides.
(b) Measure the resistance between the applicable terminals
of the connectors.
HINT:
Measure the resistance while lightly shaking the wire har-
ness vertically and horizontally.
When tester probes are inserted into a connector, insert
the probes from the back. For waterproof connectors in
which the probes cannot be inserted from the back, be
careful not to bend the terminals when inserting the tester
probes.
3. RESISTANCE CHECK (SHORT CIRCUIT CHECK)
(a) Disconnect the connectors on both ends.
(b) Measure the resistance between the applicable terminals
of the connectors and body ground. Be sure to carry out
this check on the connectors on both ends.
Resistance: 1 MΩ or higher
HINT:
Measure the resistance while lightly shaking the wire harness
vertically and horizontally.
4. VISUAL CHECK AND CONTACT PRESSURE CHECK
(a) Disconnect the connectors at both ends.
(b) Check for rust or foreign material, etc. in the terminals of
the connectors.
(c) Check crimped portions for looseness or damage and
check if the terminals are secured in lock portion.
HINT:
The terminals should not come out when pulled lightly.
(d) Prepare a test male terminal and insert it in the female ter-
minal, then pull it out.
NOTICE:
When testing a gold−plated female terminal, always use a
gold−plated male terminal.
HINT:
When the test terminal is pulled out more easily than others,
there may be poor contact in that section.

Downloaded from www.Manualslib.com manuals search engine IN02L−01
− INTRODUCTIONTERMS
IN−31
31 Author: Date:
1996 TOYOTA T100 (RM449U)
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti−Lock Brake System
A.D.D.Automatic Disconnecting Differential
A/TAutomatic Transmission
AT FAutomatic Transmission Fluid
BTDCBefore Top Dead Center
Calif.California
CBCircuit Breaker
Diff.LockDifferential Locking System
DPDash Pot
ECUElectronic Control Unit
E/GEngine
ELREmergency Locking Retractor
ESAElectronic Spark Advance
EXExhaust (Manifold, Valve)
FIPGFormed in Place Gasket
FLFusible Link
FPUFuel Pressure Up
FrFront
IGIgnition
INIntake (Manifold, Valve)
J/BJunction Block
LHLeft−Hand
LLCLong Life Coolant (Year Around Coolant)
LSPVLoad Sensing Proportioning Valve
Max.Maximum
Min.Minimum
MPMultipurpose
M/TManual Transmission
O/D, ODOverdrive
OHCOver Head Camshaft
O/SOversize
PCVPositive Crankcase Ventilation
PSPower Steering
RHRight−Hand
RrRear
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
SWSwitch
TDCTop Dead Center
TEMP.Temperature

Downloaded from www.Manualslib.com manuals search engine MA001−28
− MAINTENANCEOUTSIDE VEHICLE
MA−1
36 Author: Date:
1996 TOYOTA T100 (RM449U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge.
If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts.
If necessary, tighten them.
4. TIRE ROTATION
Check the owner’s manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean.
If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all latches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.

Downloaded from www.Manualslib.com manuals search engine MA002−05
MA−2
− MAINTENANCEINSIDE VEHICLE
37 Author: Date:
1996 TOYOTA T100 (RM449U)
INSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner’s responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified freeplay. Be alert for changes in steering condition, such as hard steering,
excessive freeplay or strange noises.
11. SEATS
(a) Check that the seat adjusters operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latch position.
(d) For fold−down seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.

Downloaded from www.Manualslib.com manuals search engine − MAINTENANCEINSIDE VEHICLE
MA−3
38 Author: Date:
1996 TOYOTA T100 (RM449U)
13. ACCELERATOR PEDAL
Check the pedal for smooth operation and uneven pedal effort or catching.
14. CLUTCH PEDAL
(See page CL−2)
(a) Check the pedal for smooth operation.
(b) Check that the pedal has the proper freeplay.
15. BRAKE PEDAL
(See page BR−6)
(a) Check the pedal for smooth operation.
(b) Check that the pedal has the proper reserve distance and freeplay.
(c) Check the brake booster function.
16. BRAKES
At a safe place, check that the brakes do not pull to one side when applied.
17. PARKING BRAKE
(See page BR−8)
(a) Check that the lever has the proper travel.
(b) On a safe incline, check that the vehicle is held securely with only the parking brake applied.
18. AUTOMATIC TRANSMISSION ”PARK” MECHANISM
(a) Check the lock release button of the selector lever for proper and smooth operation.
(b) On a safe incline, check that the vehicle is held securely with the selector lever in ”P” position and all
brakes released.

Downloaded from www.Manualslib.com manuals search engine MA003−05
MA−4
− MAINTENANCEUNDER HOOD
39 Author: Date:
1996 TOYOTA T100 (RM449U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the FULL and LOW lines on the see−through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upper and lower level lines on the case.
6. BRAKE AND CLUTCH FLUID LEVELS
Check that the brake and clutch fluid levels are near the upper level line on the see−through reservoirs.
7. ENGINE DRIVE BELTS
Check all drive belts for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temperature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking brake applied, shift the selector into all positions from the P to
L, and then shift into the P position.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re−insert the dipstick and check that the
fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 − 80°C, 158 − 176°F).
HINT:
Wait until the engine cools down (approx. 30 min.) before checking the fluid level after extended driving at
high speeds, in hot weather, in heavy traffic or pulling a trailer.
11. EXHAUST SYSTEM
(a) Visually inspect for cracks, holes or loose supports.
(b) If any change in the sound of the exhaust or smell of the exhaust fumes is noticed, have the cause
located and corrected.

Downloaded from www.Manualslib.com manuals search engine MA0568
B02099
B02100
− MAINTENANCECHASSIS
MA−13
48 Author: Date:
1996 TOYOTA T100 (RM449U)
12. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) Tighten these parts:
Seat mounting bolts
Torque:
37 N·m (375 kgf·cm, 27 ft·lbf)

2WD:
Strut bar bracket−to−frame mounting bolts
Torque: 52 N·m (530 kgf·cm, 38 ft·lbf)
Leaf spring U−bolt mounting nuts
Torque: 133 N·m (1,350 kgf·cm, 98 ft·lbf )
(b) Under Severe Conditions:
In addition to the above maintenance items, check for
loose or missing bolts and nuts on the following.
Steering system
Drive train
Suspension system
Fuel tank mounts
Engine mounts, etc.
13. FINAL INSPECTION
(a) Check operation of body parts:
Hood:
Auxiliary catch operates properly
Hood locks securely when closed
Doors:
Door locks operate properly
Doors close properly
Seats:
Seat adjusts easily and locks securely in any
positions
Seat backs lock securely at any angle
Fold−down seat backs lock securely
(b) Road test:
Engine and chassis parts do not have abnormal
noises.
Vehicle does not wander or pull to one side.
Brakes work properly and do not drag.

Downloaded from www.Manualslib.com manuals search engine PP0G8−01
PP−6
− PREPARATIONENGINE MECHANICAL (3RZ−FE)
1996 TOYOTA T100 (RM449U)
EQUIPMENT
Caliper gauge
CO/HC meter
Compression gauge
Connecting rod aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune−up tester
Heater
Magnetic finger
Micrometer
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Soft brush
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
V−block
Valve seat cutter
Vernier calipers