engine TOYOTA T100 1996 Factory Service Manual

Downloaded from www.Manualslib.com manuals search engine DI0U9−01
Vehicle Brought to Workshop
Customer Problem Analysis P. DI−128
Problem Symptom Confirmation
If the engine does not start, perform steps 10 and 12 firstConnect the OBD II scan tool or TOYOTA hand−held tester to DLC3 P. DI−129
If the display indicates a communication fault in the tool, inspect DLC3 P. DI−129
Check DTC and Freezed Frame Data (Precheck)
Record or Print DTC and Freezed Frame Data P. DI−129
Clear DTC and Freezed Frame Data P. DI−129
Visual Inspection
Setting the Check Mode Diagnosis P. DI−129
Symptom Simulation P. IN−16
DTC Chart P. DI−140
Problem Symptoms Table P. DI−148
Circuit Inspection P. DI−149
Adjustment, Repair
DTC Check P. DI−129
Titles insideare titles of pages in
in the bottom portion. See the indicated
pages for detailed explanations.this manual with the page number indicated
Malfunction
occurs.Malfunction does not occur.
Parts Inspection
Check for Intermittent Problems P. DI−129
Identification of Problem
Confirmation Test
End 1
2
3
4
5
6
7
108
9
11
12
13
15 14
16
Normal Malfunction code.
17Basic Inspection P. DI−129
− DIAGNOSTICSENGINE (5VZ−FE)
DI−127
384 Author: Date:
1996 TOYOTA T100 (RM449U)
ENGINE (5VZ−FE)
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshoot in accordance with the procedure on the following page.

Downloaded from www.Manualslib.com manuals search engine DI0UA−01
ENGINE CONTROL SYSTEM Check Sheet
Customer’s Name
Driver’s Name
Date Vehicle
Brought in
License No.
Model and Model
Year
Frame No.
Engine Model
Odometer Reading
km
miles
Problem Symptoms
Engine does
not Start
Difficult to
Start
Poor Idling
Poor
Driveability
Engine Stall
Others
Engine does not crankNo initial combustionNo complete combustion
Engine cranks slowly
Other
Incorrect first idleIdling rpm is abnormalHigh ( rpm)Low ( rpm)
Rough idling
Other
HesitationBack fireMuffler explosion (after−fire)Surging
Knocking
Other
Soon after startingAfter accelerator pedal depressed
After accelerator pedal released
During A/C operation
Shifting from N to D
Other
Dates Problem
Occurred
Problem Frequency
Condition When
Problem Occurs
Weather
Engine Operation
Engine Temp. Place Outdoor Temp.Constant
Sometimes ( times per day/month)Once only
Other
Fine
CloudyRainySnowyVarious/Other
Hot
Warm CoolCold (approx. °F/ °C)
Highway
SuburbsInner cityUphillDownhill
Rough road
Other
Cold
Warming upAfter warming upAny temp.Other
Starting
Just after starting ( min.)IdlingRacing
Driving
Constant speedAccelerationDeceleration
A/C switch ON/OFF
Other
Condition of MILRemains on Sometimes lights up Does not light up
NormalMalfunction code(s) (code )
Freezed frame data ( )
NormalMalfunction code(s) (code )
Freezed frame data ( )
Normal Mode
(Precheck)
Check Mode DTC InspectionInspector’s
Name
DI−128
− DIAGNOSTICSENGINE (5VZ−FE)
1996 TOYOTA T100 (RM449U)
CUSTOMER PROBLEM ANALYSIS CHECK

Downloaded from www.Manualslib.com manuals search engine FI0534
DI0UB−02
FI7231
TOYOTA Hand−Held Tester
DLC 3
− DIAGNOSTICSENGINE (5VZ−FE)
DI−129
1996 TOYOTA T100 (RM449U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand−
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on−
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Codes (DTCs) prescribed by SAE J2012
are recorded in the ECM memory (See page
DI−140).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTCs remain recorded in the ECM memory.
To check the DTCs, connect the OBD II scan tool or
TOYOTA hand−held tester to the Data Link Con-
nector 3 (DLC3) on the vehicle. The OBD II scan
tool or TOYOTA hand−held tester also enables you
to erase the DTCs and check freezed frame data
and various forms of engine data (For operating
instructions, see the OBD II scan tool’s instruction
book.).
DTCs include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI−140).

Downloaded from www.Manualslib.com manuals search engine N09214
DLC3 DI−130
− DIAGNOSTICSENGINE (5VZ−FE)
1996 TOYOTA T100 (RM449U)
The diagnosis system operates in normal mode
during normal vehicle use. It also has a check mode
for technicians to simulate malfunction symptoms
and troubleshoot. Most DTCs use 2 trip detection
logic* to prevent erroneous detection, and ensure
thorough malfunction detection. By switching the
ECM to check mode when troubleshooting, the
technician can cause the MIL to light up for a mal-
function that is only detected once or momentarily
(TOYOTA hand−held tester only).
*2 trip detection logic: When a logic malfunction is
first detected, the malfunction is temporarily stored
in the ECM memory. If the same malfunction is de-
tected again during the 2nd drive test, this 2nd
detection causes the MIL to light up.
The 2 trip repeats the same mode a 2nd time. (How-
ever, the ignition switch must be turned OFF be-
tween the 1st trip and 2nd trip.)
Freeze frame data:
Freeze frame data records the engine condition
when a misfire (DTCs P0300 − P0306) or fuel trim
malfunction (DTCs P0171, P0172) or other mal-
function (first malfunction only), is detected.
Because freeze frame data records the engine
conditions (fuel system, calculator load, engine
coolant temperature, fuel trim, engine speed, ve-
hicle speed, etc.) when the malfunction is detected,
when troubleshooting it is useful for determining
whether the vehicle was running or stopped, the en-
gine warmed up or not, the air−fuel ratio lean or rich,
etc. at the time of the malfunction.
Priorities for troubleshooting:
If troubleshooting priorities for multiple DTCs are given in the
applicable DTC chart, these should be followed.
If no instructions are given troubleshoot DTCs according to the
following priorities.
(1) DTCs other than fuel trim malfunction (DTCs
P0171, P0172), EGR (DTCs P0401, P0402) and
misfire (DTCs P0300 − P0306).
(2) Fuel trim malfunction (DTCs P0171, P0172) and
EGR (DTCs P0401, P0402).
(3) Misfire (DTCs P0300 − P0306).
(b) Check the DLC3
The vehicle’s ECM uses V.P.W. (Variable Pulse Width) for
communication to comply with SAE J1850. The terminal
arrangement of DLC3 complies with SAE J1962 and
matches the V.P.W. format.

Downloaded from www.Manualslib.com manuals search engine A00653
w/o Tachometer
w/ Tachometer
− DIAGNOSTICSENGINE (5VZ−FE)
DI−131
1996 TOYOTA T100 (RM449U) Terminal No.
Connection / Voltage or ResistanceCondition
2Bus  Line / Pulse generationDuring transmission
4Chassis Ground ↔ Body Ground / 1 Ω or lessAlways
5Signal Ground ↔ Body Ground / 1 Ω or lessAlways
16Battery Positive ↔ Body Ground / 9 − 14 VAlways
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
2. INSPECT DIAGNOSIS (Normal Mode)
(a) Check the MIL
(1) The MIL comes on when the ignition switch is turned
ON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−36).
(2) When the engine started, the MIL should go off. If
the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system.
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only: When the diagnosis sys-
tem is switched from normal mode to check mode, it erases
all DTCs and freezed frame data recorded in normal mode.
So before switching modes, always check the DTCs and
freezed frame data, and note them down.
(1) Prepare the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand−
held tester to the DLC3 at the lower of the instru-
ment panel.
(3) Turn the ignition switch ON and push the OBD II
scan tool or TOYOTA hand−held tester switch ON.
(4) Use the OBD II scan tool or TOYOTA hand−held
tester to check the DTCs and freezed frame data,
note them down. (For operating instructions, see
the OBD II scan tool’s instruction book.)
(5) See page DI−129 to confirm the details of the
DTCs.

Downloaded from www.Manualslib.com manuals search engine FI3605
Flashing
ON
OFF
0.13 Seconds
DI−132
− DIAGNOSTICSENGINE (5VZ−FE)
1996 TOYOTA T100 (RM449U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand−held tester) to check the DTCs, use
normal mode. For code on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the 1st time. Then repeat the simula-
tion process again. When the problem has been simulated
twice, the MIL lights up and the DTCs are recorded in the
ECM.
3. INSPECT DIAGNOSIS (Check Mode)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC.
(1) Initial conditions
Battery positive voltage 11 V or more
Throttle valve fully closed
Transmission in ”P” or ”N” position
Air conditioning switched OFF
(2) Turn the ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 at
the lower of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA
hand−held tester switch ON.
(6) Switch the TOYOTA hand−held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Start the engine. (The MIL goes out after the engine
start.)
(8) Simulate the conditions of the malfunction de-
scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTCs, etc.
(9) After simulating the malfunction conditions, use the
TOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. Turning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode. so all DTCs, etc. are erased.
(10) After checking the DTC, inspect the applicable cir-
cuit.

Downloaded from www.Manualslib.com manuals search engine − DIAGNOSTICSENGINE (5VZ−FE)
DI−133
1996 TOYOTA T100 (RM449U)
(b) Clear the DTC.
The following actions will erase the DTCs and freezed
frame data.
(1) Operating the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester to erase the
codes (See the OBD II scan tool’s instruction book
for operating instructions.).
(2) Disconnecting the battery terminals or EFI fuse.
NOTICE:
If the TOYOTA hand−held tester switches the ECM from
normal mode to check mode or vice−versa, or if the igni-
tion switch is turned from ON to ACC or OFF during check
mode, the DTCs and freezed frame data will be erased.
4. FAIL−SAFE CHART
If any of the following codes is recorded, the ECM enters fail−safe mode.
DTC No.Fail−Safe OperationFail−Safe Deactivation Conditions
P0100Ignition timing fixed at 10° BTDCReturned to normal condition
P0110Intake air temp. is fixed at 20°C (68°F)Returned to normal condition
P0115Engine coolant temp. is fixed at 80°(176°F)Returned to normal condition
P0120VTA is fixed at 0°
Following condition must be repeated at least 2 times
consecutively
0.1 V  VTA  0.95 V
P0135
P0141Heater circuit in which an abnormality is detected is
turned offIgnition switch OFF
P0325
P0330Max. timing retardationIgnition switch OFF
P1300Fuel cutIGF signal is detected for 6 consective ignitions
5. CHECK FOR INTERMITTENT PROBLEMS
HINT:
TOYOTA HAND−HELD TESTER only:
By putting the vehicle’s ECM in check mode, 1 trip detection logic is possible instead of 2 trip detection logic
and sensitivity to detect open circuits is increased. This makes it easier to detect intermittent problems.
(a) Clear the DTCs (See step 3).
(b) Set the check mode (See step 3).
(c) Perform a simulation test (See page IN−16).
(d) Check the connector and terminal (See page IN−26).
(e) Handle the connector (See page IN−26).
6. BASIC INSPECTION
When the malfunction code is not confirmed in the DTC check, troubleshooting should be performed in the
order for all possible circuits to be considered as the causes of the problems. In many cases, by carrying
out the basic engine check shown in the following flow chart, the location causing the problem can be found
quickly and efficiently. Therefore, use of this check is essential in engine troubleshooting.
1 Is battery positive voltage 11 V or more when engine is stopped?
NO Charge or replace battery.

Downloaded from www.Manualslib.com manuals search engine P00495
Outside
Inside
DI−134
− DIAGNOSTICSENGINE (5VZ−FE)
1996 TOYOTA T100 (RM449U)
YES
2 Is engine cranked?
NO Proceed to page ST−6 and continue to trouble-
shoot.
YES
3 Does engine start?
NO Go to step 7.
YES
4 Check air filter.
PREPARATION:
Remove the air filter.
CHECK:
Visual check that the air filter is not dirty or excessive oily.
HINT:
If necessary, clean the filter with compressed air. First blow from
inside thoroughly, then blow from outside of the filter.
NG Repair or replace.
OK

Downloaded from www.Manualslib.com manuals search engine P19970
P21121
A00097
SST
DLC1 E1
TE1
DLC1
− DIAGNOSTICSENGINE (5VZ−FE)
DI−135
1996 TOYOTA T100 (RM449U)
5 Check idle speed.
PREPARATION:
(a) Warm up the engine to normal operating temperature.
(b) Switch off all the accessories.
(c) Switch off air conditioning.
(d) Shift the transmission into ”N” position.
(e) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3 on the vehicle.
CHECK:
Use ”CURRENT DATA” to check the idle speed.
OK:
Idle speed: 650 − 750 rpm
NG Proceed to problem symptoms table on page
DI−148.
OK
6 Check ignition timing.
PREPARATION:
(a) Warm up the engine to normal operating temperature.
(b) Shift the transmission into ”N” position.
(c) Keep the engine speed at idle.
(d) Using SST, connect terminals TE1 and E1 of the DLC1.
SST 09843−18020
(e) Using a timing light, connect the tester to the No.1 high−
tension cord.
CHECK:
Check the ignition timing.
OK:
Ignition timing: 8 − 12° BTDC at idle
NG Proceed to page Ignition system and continue
to troubleshoot.
OK
Proceed to problem symptoms table on page
DI−148.

Downloaded from www.Manualslib.com manuals search engine BE6653A00773A00788
ON
Fuel Inlet Hose
DI−136
− DIAGNOSTICSENGINE (5VZ−FE)
1996 TOYOTA T100 (RM449U)
7 Check fuel pressure.
PREPARATION:
(a) Be sure that enough fuel is in the tank.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and push the TOYOTA hand−
held tester main switch ON.
(d) Use ”ACTIVE TEST” mode to operate the fuel pump.
(e) Please refer to the TOYOTA hand−held tester operator’s
manual for further details.
(f) If you have no TOYOTA hand−held tester, connect the
positive (+) and negative (−) leads from the battery to the
fuel pump connector (See page SF−5).
CHECK:
Check for fuel pressure in the fuel inlet hose when it is pinched
off.
HINT:
At this time, you will hear a fuel flowing noise.
NG Proceed to page SF−5 and continue to trouble-
shoot.
OK