key battery TOYOTA TACOMA 2002 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2002, Model line: TACOMA, Model: TOYOTA TACOMA 2002Pages: 23, PDF Size: 0.78 MB
Page 2 of 23

Page 20 TOYOTARS3200 REMOTE KEYLESS Security system
To better understand the features and functions of this security system, please read this
Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTIONPAGE
INTRODUCTION
2
REMOTE CONTROL INFORMATION
THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTION–RS3200 FEATURES4, 5
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)6
DISARMING THE RS3200 (except PASSIVE DISARMING) 7
PASSIVE (AUTOMATIC) ARMING & DISARMING 8
AUTOMATIC REARMING 9
ARMING SUSPENSION 9
MISCELLANEOUS
DOOR AJAR WARNING10
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10
REMOTE CONTROL RANGE 10
ALARM INFORMATION
PANIC MODE OPERATION11
ALARM TRIGGERS 12
ALARM DESCRIPTIONS 13
STOPPING AN ALARM 13
GLASS BREAKAGE SENSOR INFORMATION
GLASS BREAKAGE SENSOR CHECK PROCEDURE 14
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY15
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION 16, 17
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT
REMOVE THE BATTERY 19
INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION21
REMOTE CONTROL BATTERY REPLACEMENT
INSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can
interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the
battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to “snap” together.
TOYOTARS3200 remote keyless Security systemPage 1
Page 3 of 23

INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s
Guide completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RMand
D
ISARMat the same time you remotely lock and unlock the doors. The system provides comprehen-
sive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGEREDand sound an ALARMwhen a door,
trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During
the A
LARM, the vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.
A l s o , the vehicle ’s starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the STATUSMONITOR� �for this system. Illustrated
below, this panel holds the LED indicator (for the system ’s operating status) and the G
LASS
BREAKAGESENSOR’Smicrophone. In vehicles with an engine immobilizer, there is already a LED�
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED� and a micro-
phone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUSMONITOR. If you do not know where the LED is
located, refer to your vehicle ’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle ’s doors when you turn the key in
the ignition switch to the “ON” or “START” position, and unlock them when you turn the key back
to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer
to page 18 for programming information.
* When the system is P
ASSIVELY(AUTOMATICALLY) ARMED, there is an ENTRYDELAYthat will
elapse when a door is opened before an A
LARMis TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE ILLUSTRATED HERE
LIGHTS FOR30 SECONDS(PRE-ARMING)THEN STARTSFLASHING
(SYSTEM ISARMED)
Page 2 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 19
� �
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recom-
mend that you replace the batteries at least once a year, or when the remote control ’s transmitting
range diminishes. You may obtain the replacement battery from your Toyota dealer, as well as
many retailers that sell watch batteries.
The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it down.
6. Pry the back edge of the battery up and toward you.
�
Page 11 of 23

ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by
pressing the PANIC button on the back of the remote control. Unless you D
ISARMthe PANICALARM
by one of the described methods, it will continue for 60 seconds, then stop.
To activate the PANICALARM:
Press the PANIC button on the back of the remote control. Simultaneously:The horn sounds repeatedly for 60 seconds.�
The headlights flash repeatedly for 60 seconds.�
The tail and marker lights flash repeatedly for 60 seconds.�
The interior lights turn on for 60 seconds.�
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANICALARMat any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARMTRIGGERduring the PANICALARM, the
regular A
LARMtakes over. See ALARM INFORMATION on pages 12 and 13 for additional
information.
Page 10 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 11
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOORAJARWARNINGwhen you attempt to REMOTEARMthe
system while a door is open. To stop the warning tone, either close the open door, or press and
release the UNLOCK button on the remote control. To A
RMthe system, press the LOCK button
again.
Note: The D
OORAJARWARNINGwill not sound when the trunk is open; the doors will lock, but the
system will not A
RMuntil the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle ’s doors when you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the system ’s programming. Refer to page 18 for
programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200 ’s remote controls is 50 feet. However, several factors that
may affect your remote control ’s actual performance, include, but are not limited to:
�The remote control’s battery strength* (weak battery = decreased performance).
�Your position relative to the vehicle (dependent on the system ’s antenna wire location).
�Objects in the path between you and your vehicle.
�Your surroundings (in a parking structure, out in the open, etc.).
�Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROL ’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS
CLOSED, TURN THE KEY TO
THE“ON” OR“LOCK”POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY.PRESS THE
LOCK BUTTON ON THE
REMOTE
CONTROL
,OR...
PRESS THE
PANIC BUTTON AGAIN
, OR...
PRESS THE UNLOCK
BUTTON ON
THE REMOTE CONTROL
,OR...
LOCK THE DOORS
WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK WITH THE KEY
WHEN THE KEY IS TURNED
BACK TO THE
“ACC” OR“LOCK” POSITION...
ALL THE DOORS ARE UNLOCKED.
THE HORN SOUNDSFOR60 SECONDS
�
HEADLIGHTS FLASHFOR60 SECONDS MARKER LIGHTS
FLASH
FOR60 SECONDS TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR
60 SECONDS
Page 12 of 23

ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by
pressing the PANIC button on the back of the remote control. Unless you D
ISARMthe PANICALARM
by one of the described methods, it will continue for 60 seconds, then stop.
To activate the PANICALARM:
Press the PANIC button on the back of the remote control. Simultaneously:The horn sounds repeatedly for 60 seconds.�
The headlights flash repeatedly for 60 seconds.�
The tail and marker lights flash repeatedly for 60 seconds.�
The interior lights turn on for 60 seconds.�
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANICALARMat any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARMTRIGGERduring the PANICALARM, the
regular A
LARMtakes over. See ALARM INFORMATION on pages 12 and 13 for additional
information.
Page 10 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 11
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOORAJARWARNINGwhen you attempt to REMOTEARMthe
system while a door is open. To stop the warning tone, either close the open door, or press and
release the UNLOCK button on the remote control. To A
RMthe system, press the LOCK button
again.
Note: The D
OORAJARWARNINGwill not sound when the trunk is open; the doors will lock, but the
system will not A
RMuntil the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle ’s doors when you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the system ’s programming. Refer to page 18 for
programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200 ’s remote controls is 50 feet. However, several factors that
may affect your remote control ’s actual performance, include, but are not limited to:
�The remote control’s battery strength* (weak battery = decreased performance).
�Your position relative to the vehicle (dependent on the system ’s antenna wire location).
�Objects in the path between you and your vehicle.
�Your surroundings (in a parking structure, out in the open, etc.).
�Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROL ’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS
CLOSED, TURN THE KEY TO
THE“ON” OR“LOCK”POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY.PRESS THE
LOCK BUTTON ON THE
REMOTE
CONTROL
,OR...
PRESS THE
PANIC BUTTON AGAIN
, OR...
PRESS THE UNLOCK
BUTTON ON
THE REMOTE CONTROL
,OR...
LOCK THE DOORS
WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK WITH THE KEY
WHEN THE KEY IS TURNED
BACK TO THE
“ACC” OR“LOCK” POSITION...
ALL THE DOORS ARE UNLOCKED.
THE HORN SOUNDSFOR60 SECONDS
�
HEADLIGHTS FLASHFOR60 SECONDS
MARKER LIGHTS FLASH
FOR
60 SECONDS
TAIL LIGHTS FLASH FOR60 SECONDS
INTERIOR LIGHTS TURN ON FOR60 SECONDS
Page 20 of 23

INTRODUCTION
Congratulations on your choice of the RS3200 remote keyless security system to protect your
vehicle! To get the most from the system, we strongly recommend that you read this Owner’s
Guide completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to A
RMand
D
ISARMat the same time you remotely lock and unlock the doors. The system provides comprehen-
sive security protection through point-of-entry monitoring, glass breakage detection and ignition
switch monitoring. While A
RMED, the system will be TRIGGEREDand sound an ALARMwhen a door,
trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During
the A
LARM, the vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.
A l s o , the vehicle ’s starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the STATUSMONITOR� �for this system. Illustrated
below, this panel holds the LED indicator (for the system ’s operating status) and the G
LASS
BREAKAGESENSOR’Smicrophone. In vehicles with an engine immobilizer, there is already a LED�
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED� and a micro-
phone mounted in a separate location. If your vehicle falls into this category, remember to look at
that LED when the information refers to the S
TATUSMONITOR. If you do not know where the LED is
located, refer to your vehicle ’s owner’s guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicle ’s doors when you turn the key in
the ignition switch to the “ON” or “START” position, and unlock them when you turn the key back
to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the system; refer
to page 18 for programming information.
* When the system is P
ASSIVELY(AUTOMATICALLY) ARMED, there is an ENTRYDELAYthat will
elapse when a door is opened before an A
LARMis TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS(PRE-ARMING)THEN STARTS
FLASHING
(SYSTEM ISARMED)
Page 2 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 19
� �
REMOTE CONTROL BATTERY REPLACEMENT
The following shows the procedure to replace the batteries in your remote controls. We recom-
mend that you replace the batteries at least once a year, or when the remote control ’s transmitting
range diminishes. You may obtain the replacement battery from your Toyota dealer, as well as
many retailers that sell watch batteries.
The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it down.
6. Pry the back edge of the battery up and toward you.
�
Page 21 of 23

Page 20 TOYOTARS3200 REMOTE KEYLESS Security system
To better understand the features and functions of this security system, please read this
Owner’s Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTIONPAGE
INTRODUCTION
2
REMOTE CONTROL INFORMATION
THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTION–RS3200 FEATURES4, 5
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)6
DISARMING THE RS3200 (except PASSIVE DISARMING) 7
PASSIVE (AUTOMATIC) ARMING & DISARMING 8
AUTOMATIC REARMING 9
ARMING SUSPENSION 9
MISCELLANEOUS
DOOR AJAR WARNING10
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10
REMOTE CONTROL RANGE 10
ALARM INFORMATION
PANIC MODE OPERATION11
ALARM TRIGGERS 12
ALARM DESCRIPTIONS 13
STOPPING AN ALARM 13
GLASS BREAKAGE SENSOR INFORMATION
GLASS BREAKAGE SENSOR CHECK PROCEDURE 14
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY15
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION 16, 17
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT
REMOVE THE BATTERY 19
INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION21
REMOTE CONTROL BATTERY REPLACEMENT
INSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can
interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the
battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to “snap” together.
TOYOTARS3200 remote keyless Security systemPage 1
Page 22 of 23

TOYOTARS3200 remote keyless Security systemPage 21
Warning
•This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do
not use in vehicles with 24V specifications
. Otherwise, damage to the unit or a fire may result.
•To prevent accidents from occurring, keep the remote controls ’ batteries out of the reach of
children. In the event a battery is swallowed, consult a physician immediately.
•Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric
shock may result.
•When replacing fuses, be sure to use fuses with the same specified capacity (amperage.)
Otherwise, damage to the unit or vehicle, fire or electric shock may result.
•If an abnormal condition occurs, such as liquids spilling onto the product, or the product
emitting smoke or strange odors, stop using it immediately and consult the dealer from whom
you purchased the product. Continued use of the product before corrective actions are taken
may result in an accident, injury or fire.
•Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation
may occur.
Caution
•Do not use batteries other than the type specified.
•When placing batteries into the product, insert them as shown, paying close attention to the
polarities (+ and -). If inserted improperly, the battery may explode, or leak electrolyte and
contaminate the surrounding area.
•Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock
or injury may result.
•Do not allow children to play with the remote controls. Otherwise, the doors may be locked or
unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.
•If this product is dropped or its case is damaged, disconnect the power supply lead and
contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric
shock may result.