stop start TOYOTA TACOMA 2002 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2002, Model line: TACOMA, Model: TOYOTA TACOMA 2002Pages: 23, PDF Size: 0.78 MB
Page 6 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the driver’s door when the UNLOCK button is pressed on the
remote control, then unlock the remaining doors when the UNLOCK button is pressed again within
3 seconds. You may change the programming so all doors will unlock at once when the UNLOCK
button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door.(Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 5
FEATURESFUNCTIONS
When an ALARMis TRIGGERED, the system disables the vehicle ’s
starter and prevents engine start until the system is reset (D
ISARMED).
During an A
LARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the A
LARM.
The user is notified that an A
LARMoccurred. Upon DISARMINGthe
system after an A
LARMwas TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the B
UZZERsounds, for 2 seconds.
You may T
RIGGERa PANICALARM, by pressing the PANICbutton on the
back of the remote control, to draw attention to your vehicle. During
the P
ANICALARM, the head, tail and marker lights flash, and the horn
sounds, but the starter is not disabled.
The RS3200 flashes the vehicle ’s tail and marker lights during
R
EMOTEARMINGand REMOTEDISARMING, as well as during an ALARM.
Also, the headlights flash during an A
LARM.
When the system is R
EMOTEDISARMED, it turns on the interior lights in
the vehicle for 30 seconds, or until the key is inserted into the
ignition switch. It also turns them on during an A
LARM.
During an A
LARM, the RS3200 activates the vehicle ’s horn.
If power to the RS3200 is disrupted while it is A
RMED, an ALARM
is TRIGGEREDonce power is restored.
This panel houses the G
LASSBREAKAGESENSORmicrophone and the
flashing LED that indicates the operating status of the security system.
(In vehicles with an engine immobilizer system, that system ’s LED and
a separate microphone are used instead.)
The RS3200 utilizes a P
IEZOBUZZER, usually mounted in the engine
compartment, to sound confirmation “chirps” and tones for function
confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle ’s doors when you turn
the ignition key to “ON” or “START”, and unlocks the doors when you
turn the key back to “ACC” or “LOCK”.*
The Buzzer sounds for 5 seconds when you attempt to R
EMOTEARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with
the RS3200 is approximately 50 feet. Please refer to page 10 for a
description of factors that may affect the performance (operating
range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming information. STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
PANIC MODE
OPERATION
EXTERIOR LIGHT
ACTIVATION
INTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED
AUTOMATIC DOOR
LOCK/UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
BRIEF DESCRIPTION
–RS3200 FEATURES
a. Insert the key into,
and
remove it
from the ignition
switch
2 times.
e. Insert the key into
the ignition and
leave it in.
c. Insert the key into,
and
remove it
from the ignition
switch
1 time.
g. Turn the key from
LOCK to ON
4
times
(ending at
LOCK.)
h. Remove the key
from the ignition
switch.i.The tail and marker lights flash 4times, the
buzzer
chirps 4times, and the doors lock and
unlock
4times.
b. Close, then open
the driver ’s door
2 times.
f. Closethe driver ’s
door.d. Close, then open
the driver ’s door
2 times.
Page 8 of 23
Page 14 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 7
OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMEDin several ways. Do oneof the following:
Unlock the doors with your key:
Insert the key into the door key switch and turn it toward the rear of
the vehicle:The S
TATUSMONITOR’SLED stops flashing.� The system is
now D
ISARMED.*
In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARMwill be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously: The driver’s door unlocks.�
The vehicle ’s tail and marker lights flash twice.�
The interior lights turn on for 30 seconds.�
The STATUSMONITOR’SLED stops flashing.� The system is
now D
ISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.The S
TATUSMONITOR’SLED stops flashing.� The system is
now D
ISARMED.*
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle ’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGERMEMORYwas activated; an ALARMwas
T
RIGGEREDwhile you were away from the vehicle.
* Please note, if the system utilizes your vehicle ’s engine immobilizer system LED instead of the
S
TATUSMONITOR, the LED will continue to flash.
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO“ON” TO
DISARM THE SYSTEM
THE DRIVER
’S DOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE DISARMEDTHE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTERIORLIGHTS TURN ON FOR30 SECONDS WHEN THE SYSTEM IS
REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS
FLASHING
WHEN THE SYSTEM IS DISARMED
� � �THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring –it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed
specifically for this task, the G
LASSBREAKAGESENSORis capable of ignoring other noises, which
helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASSBREAKAGESENSOR. You may observe how it works following the procedure listed below.
1. ARMthe system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not ARMif any door, the trunk or hatch is
open.)
2. Wait until the STATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. With the tip of a key, tap the center of the driver ’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARNAWAYALARMshould be TRIGGERED. If the ALARMis not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Toyota dealer for more information.
4. DISARMthe system to stop the WARNAWAYALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARMthe system.
Page 9 of 23
Page 8 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 13
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 is programmed to PASSIVELYARM, the system will ARMafter the ignition key is
removed and all doors and the trunk or hatch are closed; you do not need to lock the doors. When
you come back to your vehicle and open a door, you must insert the key into the ignition switch
and turn it to “ON” during the E
NTRYDELAY(0, 15 or 30 seconds), or an ALARMwill be TRIGGERED. If
you lock the doors, regular A
RMINGwill override PASSIVEARMING; there will be no ENTRYDELAY. See
the PROGRAMMING section on page 15 to activate the P
ASSIVEARMINGmode, as well as select the
E
NTRYDELAYtime.
To PASSIVELYARMthe system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (
The system will not ARM
while any of the doors are open.)
Close the trunk or hatch, if necessary. (The system will not ARMwhile
the trunk or hatch is open.)
After the last door, trunk or hatch is closed: The S
TATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing.�The system is now ARMED.
To DISARMthe PASSIVELYARMEDsystem:
Enter the vehicle through a front door.
The E
NTRYDELAYbegins:
The S
TATUSMONITOR’SLED turns on (no flashing.)�
Insert the key into the ignition switch and turn it to “ON” before the
E
NTRYDELAYends.*
The LED turns off. The system is now D
ISARMED.
You may also DISARMthe system following any of the methods
described on page 7.
NOTE: If your vehicle ’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGERMEMORYwas activated; an ALARMwas
T
RIGGEREDwhile you were away from the vehicle.
* If the ENTRYDELAYtime elapses before the ignition switch is turned to “ON”, an ALARMwill be
T
RIGGERED. To DISARMthe system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control ’s UNLOCK button.
THE SYSTEM ARMS30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR, TRUNK OR HATCH) IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT TO
“ON”
LIGHTS FOR30 SECONDS(PRE-ARMING)THEN STARTSFLASHING
(SYSTEM ISARMED)
�
TURNS ON(NO
FLASHING)DURING THE
ENTRY DELAY
�
ALARM INFORMATION
ALARM DESCRIPTIONS
Regular ALARM�
When an ALARMis triggered in any way other than initial detection by the GLASSBREAKAGESENSOR,
the following occur: The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
The starter is disabled (no engine start) until the system is D
ISARMED.
The door lock will be relocked if someone reaches in and unlocks the inside lock button.
After 60 seconds of A
LARM, the system will REARMand continue to protect the vehicle.
WARN-AWAY ALARM�
Upon initial detection of noise from tapping on, or breaking glass, the GLASSBREAKAGESENSOR
TRIGGERSa WARNAWAYALARM:
The horn sounds repeatedly for 20 seconds.
The headlights flash repeatedly for 20 seconds.
The tail and marker lights flash repeatedly for 20 seconds.
The interior lights turn on for 20 seconds.
If the G
LASSBREAKAGESENSORdetects noise again, or if a door or trunk or hatch is opened while the
system is still A
RMED, the regular ALARM(described above) is activated.
STOPPING AN ALARM
Simply DISARMthe system using the remote control or key as described on page 7.
THE HORN SOUNDS
FOR20 SECONDS
�
HEADLIGHTS FLASHFOR20 SECONDS
MARKER LIGHTS FLASH
FOR
20 SECONDS
TAIL LIGHTS FLASH FOR20 SECONDS
THE HORN SOUNDS FOR60 SECONDS
HEADLIGHTS FLASHFOR60 SECONDS
THE STARTER IS DISABLED UNTIL THE SYSTEM IS DISARMED
MARKER LIGHTS FLASH
FOR
60 SECONDS TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR60 SECONDS
INTERIOR LIGHTS TURN ON FOR20 SECONDS
�
Page 11 of 23
ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by
pressing the PANIC button on the back of the remote control. Unless you D
ISARMthe PANICALARM
by one of the described methods, it will continue for 60 seconds, then stop.
To activate the PANICALARM:
Press the PANIC button on the back of the remote control. Simultaneously:The horn sounds repeatedly for 60 seconds.�
The headlights flash repeatedly for 60 seconds.�
The tail and marker lights flash repeatedly for 60 seconds.�
The interior lights turn on for 60 seconds.�
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANICALARMat any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARMTRIGGERduring the PANICALARM, the
regular A
LARMtakes over. See ALARM INFORMATION on pages 12 and 13 for additional
information.
Page 10 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 11
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOORAJARWARNINGwhen you attempt to REMOTEARMthe
system while a door is open. To stop the warning tone, either close the open door, or press and
release the UNLOCK button on the remote control. To A
RMthe system, press the LOCK button
again.
Note: The D
OORAJARWARNINGwill not sound when the trunk is open; the doors will lock, but the
system will not A
RMuntil the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle ’s doors when you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the system ’s programming. Refer to page 18 for
programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200 ’s remote controls is 50 feet. However, several factors that
may affect your remote control ’s actual performance, include, but are not limited to:
�The remote control’s battery strength* (weak battery = decreased performance).
�Your position relative to the vehicle (dependent on the system ’s antenna wire location).
�Objects in the path between you and your vehicle.
�Your surroundings (in a parking structure, out in the open, etc.).
�Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROL ’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS
CLOSED, TURN THE KEY TO
THE“ON” OR“LOCK”POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY.PRESS THE
LOCK BUTTON ON THE
REMOTE
CONTROL
,OR...
PRESS THE
PANIC BUTTON AGAIN
, OR...
PRESS THE UNLOCK
BUTTON ON
THE REMOTE CONTROL
,OR...
LOCK THE DOORS
WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK WITH THE KEY
WHEN THE KEY IS TURNED
BACK TO THE
“ACC” OR“LOCK” POSITION...
ALL THE DOORS ARE UNLOCKED.
THE HORN SOUNDSFOR60 SECONDS
�
HEADLIGHTS FLASHFOR60 SECONDS MARKER LIGHTS
FLASH
FOR60 SECONDS TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR
60 SECONDS
Page 12 of 23
ALARM INFORMATION
PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by
pressing the PANIC button on the back of the remote control. Unless you D
ISARMthe PANICALARM
by one of the described methods, it will continue for 60 seconds, then stop.
To activate the PANICALARM:
Press the PANIC button on the back of the remote control. Simultaneously:The horn sounds repeatedly for 60 seconds.�
The headlights flash repeatedly for 60 seconds.�
The tail and marker lights flash repeatedly for 60 seconds.�
The interior lights turn on for 60 seconds.�
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANICALARMat any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARMTRIGGERduring the PANICALARM, the
regular A
LARMtakes over. See ALARM INFORMATION on pages 12 and 13 for additional
information.
Page 10 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 11
MISCELLANEOUS
DOOR AJAR WARNING
The RS3200 will sound a five second DOORAJARWARNINGwhen you attempt to REMOTEARMthe
system while a door is open. To stop the warning tone, either close the open door, or press and
release the UNLOCK button on the remote control. To A
RMthe system, press the LOCK button
again.
Note: The D
OORAJARWARNINGwill not sound when the trunk is open; the doors will lock, but the
system will not A
RMuntil the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicle ’s doors when you turn the ignition
key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. If
you start the vehicle while a door is open, the system will not lock the doors; you must lock them
manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the system ’s programming. Refer to page 18 for
programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200 ’s remote controls is 50 feet. However, several factors that
may affect your remote control ’s actual performance, include, but are not limited to:
�The remote control’s battery strength* (weak battery = decreased performance).
�Your position relative to the vehicle (dependent on the system ’s antenna wire location).
�Objects in the path between you and your vehicle.
�Your surroundings (in a parking structure, out in the open, etc.).
�Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROL ’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS
CLOSED, TURN THE KEY TO
THE“ON” OR“LOCK”POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY.PRESS THE
LOCK BUTTON ON THE
REMOTE
CONTROL
,OR...
PRESS THE
PANIC BUTTON AGAIN
, OR...
PRESS THE UNLOCK
BUTTON ON
THE REMOTE CONTROL
,OR...
LOCK THE DOORS
WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK WITH THE KEY
WHEN THE KEY IS TURNED
BACK TO THE
“ACC” OR“LOCK” POSITION...
ALL THE DOORS ARE UNLOCKED.
THE HORN SOUNDSFOR60 SECONDS
�
HEADLIGHTS FLASHFOR60 SECONDS
MARKER LIGHTS FLASH
FOR
60 SECONDS
TAIL LIGHTS FLASH FOR60 SECONDS
INTERIOR LIGHTS TURN ON FOR60 SECONDS
Page 14 of 23
Page 8 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 13
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 is programmed to PASSIVELYARM, the system will ARMafter the ignition key is
removed and all doors and the trunk or hatch are closed; you do not need to lock the doors. When
you come back to your vehicle and open a door, you must insert the key into the ignition switch
and turn it to “ON” during the E
NTRYDELAY(0, 15 or 30 seconds), or an ALARMwill be TRIGGERED. If
you lock the doors, regular A
RMINGwill override PASSIVEARMING; there will be no ENTRYDELAY. See
the PROGRAMMING section on page 15 to activate the P
ASSIVEARMINGmode, as well as select the
E
NTRYDELAYtime.
To PASSIVELYARMthe system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (
The system will not ARM
while any of the doors are open.)
Close the trunk or hatch, if necessary. (The system will not ARMwhile
the trunk or hatch is open.)
After the last door, trunk or hatch is closed: The S
TATUSMONITOR’SLED turns on for 30 seconds, then
starts flashing.�The system is now ARMED.
To DISARMthe PASSIVELYARMEDsystem:
Enter the vehicle through a front door.
The E
NTRYDELAYbegins:
The S
TATUSMONITOR’SLED turns on (no flashing.)�
Insert the key into the ignition switch and turn it to “ON” before the
E
NTRYDELAYends.*
The LED turns off. The system is now D
ISARMED.
You may also DISARMthe system following any of the methods
described on page 7.
NOTE: If your vehicle ’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGERMEMORYwas activated; an ALARMwas
T
RIGGEREDwhile you were away from the vehicle.
* If the ENTRYDELAYtime elapses before the ignition switch is turned to “ON”, an ALARMwill be
T
RIGGERED. To DISARMthe system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control ’s UNLOCK button.
THE SYSTEM ARMS30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR, TRUNK OR HATCH) IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT TO
“ON”
LIGHTS FOR30 SECONDS(PRE-ARMING)THEN STARTSFLASHING
(SYSTEM ISARMED)
�
TURNS ON(NO
FLASHING)DURING THE
ENTRY DELAY
�
ALARM INFORMATION
ALARM DESCRIPTIONS
Regular ALARM�
When an ALARMis triggered in any way other than initial detection by the GLASSBREAKAGESENSOR,
the following occur: The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
The starter is disabled (no engine start) until the system is D
ISARMED.
The door lock will be relocked if someone reaches in and unlocks the inside lock button.
After 60 seconds of A
LARM, the system will REARMand continue to protect the vehicle.
WARN-AWAY ALARM�
Upon initial detection of noise from tapping on, or breaking glass, the GLASSBREAKAGESENSOR
TRIGGERSa WARNAWAYALARM:
The horn sounds repeatedly for 20 seconds.
The headlights flash repeatedly for 20 seconds.
The tail and marker lights flash repeatedly for 20 seconds.
The interior lights turn on for 20 seconds.
If the G
LASSBREAKAGESENSORdetects noise again, or if a door or trunk or hatch is opened while the
system is still A
RMED, the regular ALARM(described above) is activated.
STOPPING AN ALARM
Simply DISARMthe system using the remote control or key as described on page 7.
THE HORN SOUNDS
FOR20 SECONDS
�
HEADLIGHTS FLASHFOR20 SECONDS
MARKER LIGHTS FLASH
FOR
20 SECONDS
TAIL LIGHTS FLASH FOR20 SECONDS
THE HORN SOUNDS FOR60 SECONDS
HEADLIGHTS FLASHFOR60 SECONDS
THE STARTER IS DISABLED UNTIL THE SYSTEM IS DISARMED
MARKER LIGHTS FLASH
FOR
60 SECONDS TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR60 SECONDS
INTERIOR LIGHTS TURN ON FOR20 SECONDS
�
Page 15 of 23
Page 14 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 7
OPERATION
DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMEDin several ways. Do oneof the following:
Unlock the doors with your key:
Insert the key into the door key switch and turn it toward the rear of
the vehicle:The S
TATUSMONITOR’SLED stops flashing.� The system is
now D
ISARMED.*
In the case of Sienna and 4Runner, you may also disarm the
system using the key in the back door; all the doors will unlock at the
same time. This feature is not available for Celica; you must disarm
the system before opening the hatch, or else an A
LARMwill be
Triggered.
Unlock the doors with the remote control:
Press the UNLOCK button on the remote control. Simultaneously: The driver’s door unlocks.�
The vehicle ’s tail and marker lights flash twice.�
The interior lights turn on for 30 seconds.�
The STATUSMONITOR’SLED stops flashing.� The system is
now D
ISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the driver’s door to unlock the remaining doors.
Use the ignition switch:
Insert the key into the ignition switch, then turn it to ON.The S
TATUSMONITOR’SLED stops flashing.� The system is
now D
ISARMED.*
This method of disarming is rarely used. You must be inside the
vehicle while the system is armed in order to do it.
NOTE: If your vehicle ’s tail and marker lights turn on and the buzzer sounds for 2 seconds
when the system is D
ISARMED, the TRIGGERMEMORYwas activated; an ALARMwas
T
RIGGEREDwhile you were away from the vehicle.
* Please note, if the system utilizes your vehicle ’s engine immobilizer system LED instead of the
S
TATUSMONITOR, the LED will continue to flash.
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO“ON” TO
DISARM THE SYSTEM
THE DRIVER
’S DOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE DISARMEDTHE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTERIORLIGHTS TURN ON FOR30 SECONDS WHEN THE SYSTEM IS
REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS
FLASHING
WHEN THE SYSTEM IS DISARMED
� � �THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 provides protection for your vehicle above and beyond entry point monitoring –it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed
specifically for this task, the G
LASSBREAKAGESENSORis capable of ignoring other noises, which
helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the
G
LASSBREAKAGESENSOR. You may observe how it works following the procedure listed below.
1. ARMthe system.
Press the LOCK button on the remote control or lock the doors with
the key.
(Remember, the system will not ARMif any door, the trunk or hatch is
open.)
2. Wait until the STATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or hatch
is closed.
3. With the tip of a key, tap the center of the driver ’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in
cold weather, or you may crack or break it.
A W
ARNAWAYALARMshould be TRIGGERED. If the ALARMis not
T
RIGGERED, make sure you performed the procedure correctly and try
again. If you find that the system did not perform as expected,
contact your Toyota dealer for more information.
4. DISARMthe system to stop the WARNAWAYALARM.
Press the UNLOCK button on the remote control or use the key to
D
ISARMthe system.
Page 17 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the driver’s door when the UNLOCK button is pressed on the
remote control, then unlock the remaining doors when the UNLOCK button is pressed again within
3 seconds. You may change the programming so all doors will unlock at once when the UNLOCK
button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door.(Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 TOYOTARS3200 REMOTE KEYLESS Security systemTOYOTARS3200 remote keyless Security systemPage 5
FEATURESFUNCTIONS
When an ALARMis TRIGGERED, the system disables the vehicle ’s
starter and prevents engine start until the system is reset (D
ISARMED).
During an A
LARM, the system will lock the doors if one is unlocked,
and will continue to do so for the duration of the A
LARM.
The user is notified that an A
LARMoccurred. Upon DISARMINGthe
system after an A
LARMwas TRIGGERED, the vehicle’s tail and marker
lights will be turned on, and the B
UZZERsounds, for 2 seconds.
You may T
RIGGERa PANICALARM, by pressing the PANICbutton on the
back of the remote control, to draw attention to your vehicle. During
the P
ANICALARM, the head, tail and marker lights flash, and the horn
sounds, but the starter is not disabled.
The RS3200 flashes the vehicle ’s tail and marker lights during
R
EMOTEARMINGand REMOTEDISARMING, as well as during an ALARM.
Also, the headlights flash during an A
LARM.
When the system is R
EMOTEDISARMED, it turns on the interior lights in
the vehicle for 30 seconds, or until the key is inserted into the
ignition switch. It also turns them on during an A
LARM.
During an A
LARM, the RS3200 activates the vehicle ’s horn.
If power to the RS3200 is disrupted while it is A
RMED, an ALARM
is TRIGGEREDonce power is restored.
This panel houses the G
LASSBREAKAGESENSORmicrophone and the
flashing LED that indicates the operating status of the security system.
(In vehicles with an engine immobilizer system, that system ’s LED and
a separate microphone are used instead.)
The RS3200 utilizes a P
IEZOBUZZER, usually mounted in the engine
compartment, to sound confirmation “chirps” and tones for function
confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle ’s doors when you turn
the ignition key to “ON” or “START”, and unlocks the doors when you
turn the key back to “ACC” or “LOCK”.*
The Buzzer sounds for 5 seconds when you attempt to R
EMOTEARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with
the RS3200 is approximately 50 feet. Please refer to page 10 for a
description of factors that may affect the performance (operating
range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming information. STARTER DISABLE
FORCED LOCK
DURING ALARM
TRIGGER MEMORY
PANIC MODE
OPERATION
EXTERIOR LIGHT
ACTIVATION
INTERIOR LIGHT
ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED
AUTOMATIC DOOR
LOCK/UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
BRIEF DESCRIPTION
–RS3200 FEATURES
a. Insert the key into,
and
remove it
from the ignition
switch
2 times.
e. Insert the key into
the ignition and
leave it in.
c. Insert the key into,
and
remove it
from the ignition
switch
1 time.
g. Turn the key from
LOCK to ON
4
times
(ending at
LOCK.)
h. Remove the key
from the ignition
switch.i.The tail and marker lights flash 4times, the
buzzer
chirps 4times, and the doors lock and
unlock
4times.
b. Close, then open
the driver ’s door
2 times.
f. Closethe driver ’s
door.d. Close, then open
the driver ’s door
2 times.