warning light TOYOTA TACOMA 2009 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2009, Model line: TACOMA, Model: TOYOTA TACOMA 2009Pages: 15, PDF Size: 1.29 MB
Page 12 of 15
TOYOTARS3200 PLUSSecurity systemPage 11
GLASS BREAKAGE SENSOR INFORMATION
The RS3200 PLUSprovides protection for your vehicle above and beyond entry point monitoring–it
“listens” for the noise made by tapping on, or breaking of glass. Using a microphone designed
specifically for this task, the GLASSBREAKAGESENSORis capable of ignoring other noises, which
helps to prevent “false alarms” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 PLUSwas installed in your vehicle, care was taken to adjust the sensitivity level
of the GLASSBREAKAGESENSOR. You may observe how it works following the procedure listed
below.
1. ARMthe system.
Press the lock button on the remote control or lock the doors
with the key.
(Remember, the system will not ARMif any door, the trunk or
hatch is open.)
2. Wait until the STATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door, the trunk or
hatch is closed.
3. With the tip of a key, tap the center of the driver’s door window.
Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially
in cold weather, or you may crack or break it.
A WARNAWAYALARMshould be TRIGGERED. If the ALARMis not
TRIGGERED, make sure you performed the procedure correctly
and try again. If you find that the system did not perform as
expected, contact your Toyota dealer for more information.
4. DISARMthe system to stop the WARNAWAYALARM.
Press the unlock button on the remote control or use the key
to DISARMthe system.
TOYOTARS3200 PLUSSISTEMA DE SEGURIDAD Página 11
INFORMACIÓN SOBRE EL SENSOR CONTRA ROTURA DE CRISTALES
El RS3200 Plus es capaz de ofrecer protección a su vehículo más allá de los puntos de entrada a
éste. Es capaz de "escuchar" el ruido que se produce al golpear o romper algún cristal. Empleando
un micrófono diseñado específicamente para cumplir esta misión, el sensor contra rotura de
cristales es capaz de ignorar cualquier otro ruido, previniendo las molestas "falsas alarmas".
PROCEDIMIENTO DE VERIFICACIÓN DEL SENSOR CONTRA ROTURA DE
CRISTALES
Cuando el RS3200 Plus fue instalado en su vehículo, la sensibilidad del sensor contra rotura de
cristales fue ajustada cuidadosamente. Usted puede observar cómo trabaja siguiendo el
procedimiento que se menciona a continuación.
1. Arme el sistema.
Presione el botón para cerrar los seguros desde su control remoto o
cierre las puertas con la llave.
(Recuerde que el sistema no se armará si alguna puerta o el
maletero se encuentra abierta.)
2. Espere hasta que el LED que monitorea el estado del sistema
comience a parpadear.
El LED parpadeará 30 segundos después de que la última puerta o el
maletero haya sido cerrada.
3. Con la punta de una llave, golpee suavemente el centro de la
ventana del conductor.
Golpee la ventana con poca fuerza.
ADVERTENCIA: No golpee la ventana con fuerza excesiva
especialmente en climas fríos, ya que podría
quebrarla o romperla.
Se deberá activar una alarma de advertencia. Si la alarma no se
activa, asegúrese de que llevó a cabo el procedimiento
correctamente e inténtelo nuevamente. Si usted encuentra que el
sistema no está trabajando satisfactoriamente, contacte a su
distribuidor Toyota para más información.
4. Desarme el sistema para detener la alarma de
advertencia.
Presione el botón para liberar los seguros de la puertas
desde su control remoto o utilice su llave para desarmar el sistema.