key TOYOTA tC 2011 Accessories, Audio & Navigation (in English)
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2011, Model line: tC, Model: TOYOTA tC 2011Pages: 14, PDF Size: 0.59 MB
Page 12 of 14

Page 11 SCION SECURITY SYSTEM 
GLASS BREAKAGE SENSOR INFORMATION
The Scion Security provides protection for your vehicle above and beyond\
 entry point 
monitoring–it “listens” for the noise made by tapping on, or br\
eaking of glass. Using a 
microphone designed specifically for this task, the GLASS BREAKAGE SENSOR is 
capable of ignoring other noises, which helps to prevent “false alarm\
s” from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the Scion Security was installed in your vehicle, care was taken to\
 adjust the 
sensitivity level of the GLASS BREAKAGE SENSOR. You may observe how it works 
following the procedure listed below. 
ARM the system. 
1. 
Press the lock button on the remote control or lock the doors 
with the key.
(Remember, the system will not ARM if any door, the trunk or 
hatch is open.)  
 
 
Wait until the STATUS MONITOR’S LED starts flashing. The 
2. 
LED will flash 30 seconds after the last door, the trunk or 
hatch is closed.
* for some vehicles the LED will turn off instead of flashing  after the 30 seconds. 
 
With the tip of a key, tap the center of the driver’s door  
3. 
window. Tap the glass with light to moderate force. 
WARNING: Do not hit the glass with excessive force, especially  in cold weather, or you may crack or break it. 
A WARN AWAY ALARM should be TRIGGERED. If the 
ALARM is not TRIGGERED, make sure you performed the 
procedure correctly and try again. If you find that the system 
did not perform as expected, contact your Scion dealer for 
more information.  
DISARM the system to stop the WARN AWAY ALARM. Press 
4. 
the unlock button
SCION
SECURITY 
Page 13 of 14

SCION SECURITY SYSTEM  Page 12
PROGRAMMING
The Scion Security is factory-set to not PASSIVELY ARM. To change the system’s 
operation for PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, 
follow the procedure below. For more information on this feature, please refer to page 7.  
(Not applicable to vehicles with Smart Key system. Please consult your \
Scion 
Dealer for programming information.)  
PA S SIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
DISARM the Security system before proceeding below by using the remote c\
ontrol or 
key as described on page 6.
Before you begin:   
1. 
Open the driver’s door. Close the remaining 
doors and the trunk or hatch. Unlock all doors 
with the inside lock switch. Remove the key 
from the 
ignition 
switch.
Lock
d.  , then unlock 
the driver’s door 
inside lock button   
3 times .
The system locks the door 
f. 
in 2 seconds; if this does not 
happen, start over.
Start the Programming Procedure. (Complete these steps within 40 seconds.)
Lock
b.   then unlock the 
driver’s door inside lock 
button 1 time.The system locks the door  
c. 
in 2 seconds; if this does  
not happen, start over.  
Programming is now   
complete.
Select the Operating Mode and Complete the Programming Procedure.
3. 
Close, then Open the driver’s 
a. 
door:
2 times = PASSIVE ARMING OFF  
3 times = PASSIVE ARMING ON, 
         0 Sec. ENTRY DELAY  
4 times = PASSIVE ARMING ON, 
        15 Sec. ENTRY DELAY  
5 times = PASSIVE ARMING ON, 
        30 Sec. ENTRY DELAY
Close the 
a. 
driver’s door. Lock
b.   and unlock all doors  
3 times by key or remote 
control.Open and close 
c. 
the driver’s 
door.
Open the 
e. 
driver’s door.
Unlock the driver’s 
g. 
door.
Insert and remove the key from the igni -
2. 
tion key cylinder 3 times; this must be 
completed within 5 seconds.