transmission TOYOTA TERCEL 1985 Repair Manual

PR-z PROPELLER SHAFT - Precautions, Troubleshooting, Propeller Shaft
PRECAUTIONS
1. As the universal ioint is a non-disassembly type' the
propeller shaft or intermediate shaft must be replaced
as an assembly in the event of universalioint trouble.
2. Be careful not to grip the propeller shaft tube too tight-
ly in the vise as this will cause deformation.
TROUBLESHOOTING
ProblemPossible causeRemedyPage
NoiseSleeve yoke spline worn
Center bearing worn
Spider bearing worn or stuck
Replace intermediate shaft
Replace center bearing
Replace intermediate shaft or
propeller shaft
PR-3
PR-3
PR-3
VibrationPropeller shaft runout
Propeller shaft unbalance
Transmission extension housing rear
bushing worn
Sleeve yoke spline stuck
Center bearing height imProPer
Replace propeller shaft
Balance propeller shaft
Replace bushing
Replace intermediate shaft
Adjust bearing height
PR-3
PR-3
TA.4O
PR-3
PROPELLER SHAFT
COMPONENTS
lntermediate Shaft
---- 9-Height Washer [ 430 (3il42t
aProPeller shaftw---@III
Ffiffiiib-ntnl : Tightening torque
O : Non-reasable part
Center SuPPort Bering - -

PROPELLER SHAFT - Propeller ShaftPR.3
REMOVAL AND DISASSEMBLY OF
PROPELLER SHAFT
(See page PR-21
1. DISCONNECT PROPELLER SHAFT FLANGE FROM
COMPANION FLANGE ON DIFFERENTIAL
(a) Place matchmarks on the flanges.
(b) Remove the four bolts and nuts.
2. REMOVE TWO BOLTS HOLDING CENTER SUPPORT
BEARING TO BODY
3. REMOVE PROPELLER SHAFT WITH INTERMEDIATE
SHAFT
h) Pull out the yoke from the transmission.
(b) Insert SST in the transmission to prevent oil leakage.
ssT 09325-1 20rO
4. SEPARATE PROPELLER SHAFT AND INTERMEDIATE
SHAFT
(a) Place matchmarks on the flanges.
(b) Remove the four bolts and nuts.
5. REMOVE CENTER SUPPORT BEARING FROM
INTERMEDIATE SHAFT
(a) Using a hammer and chisel, loosen the staked part of
the nut.
(b) Using SST to hold the flange, remove the nut.
ssT 09330-00020

PR-6 PROPELLER SHAFT - Propeiler Shaft
SST
3. ASSEMBTE PROPELLER SHAFT AND
INTERMEDIATE SHAFT
(a) Align the matchmarks on the flanges and connect
them with the four bolts and nuts.
Torque: 430 kg-cm (31 ft-|b,42 N.ml
4, INSERT SLEEVE YOKE IN TRANSMISSION
{a) Apply MP grease to the outsade diameter and splines
of the yoke.
(b) Remove SST.
ssT 09325-12010
(c) Push the yoke into the transmission.
5. CONNECT PROPELLER SHAFT FLANGE TO
COMPANION FLANGE ON DIFFERENTIAL
(a) Align the matchmarks on the flanges and connect the
them with the four bolts and nuts.
(b) Torgue the nuts.
Torque: 43O kg-cm (31 ft-tb,42 N.m)
6. CONNECT CENTER SUPPORT BEARING TO BODY
ta) Place the height washer between the body and
center support bearing, and install the two mount
bolts finger tight.
NOTE: Some vehicles do not have a height washer..
In this case, it is not necessary to insert one.
(b) Check that the bearing bracket is at right angles to
the propeller shaft Adjust the bracket if necessary.
(c) Check that the center line of the center bearing is set
to the center line of the bracket when the vehicle is in
a no-load condition.
Adjust the bracket if necessary.
(d) Torque the mount bolts.
Torque: 375 kg-cm Q7 tt-ab,37 N.m)
Front 1-
Center of CenterBearing