sensor TOYOTA TERCEL 1996 Service Repair Manual

IG08I-01
S06251
Camshaft Position
SensorCamshaft Position
Sensor Connector
- IGNITIONCAMSHAFT POSITION SENSOR
IG-9
640 Author
: Date
:
1996 TERCEL (RM440U)
CAMSHAFT POSITION SENSOR
COMPONENTS

IG08J-01
IG-10
- IGNITIONCAMSHAFT POSITION SENSOR
1996 TERCEL (RM440U)
REMOVAL
REMOVE CAMSHAFT POSITION SENSOR
(a) Disconnect the camshaft position sensor connector.
(b) Remove the bolt and camshaft position sensor.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)

IG08K-04
- IGNITIONCAMSHAFT POSITION SENSOR
IG-1 1
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page IG-10).

IG08L-05
IG-12
- IGNITIONCRANKSHAFT POSITION SENSOR
643 Author
: Date
:
1996 TERCEL (RM440U)
CRANKSHAFT POSITION SENSOR
COMPONENTS

IG08M-04
P21254
Connector Clamp
P21034
- IGNITIONCRANKSHAFT POSITION SENSOR
IG-13
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT CRANKSHAFT POSITION SENSOR
CONNECTOR AND CLAMP
2. REMOVE RH ENGINE UNDER COVER
3. REMOVE NO.2 TIMING BELT COVER (See page
EM-12)
4. REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and disconnect the crankshaft position sensor.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)

IG08N-03
IG-14
- IGNITIONCRANKSHAFT POSITION SENSOR
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page IG-13).

Q06552
Q08461
AB
C
CC
A
Q06446
Q08159
- MANUAL TRANSAXLEMANUAL TRANSAXLE UNIT
MX-5
1996 TERCEL (RM440U)
14. REMOVE FRONT EXHAUST PIPE
(a) Disconnect the oxygen sensor.
(b) Remove the 2 bolts, springs and gasket.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
(c) Remove the bolt, clamp and gasket.
Torque: 19 N´m (190 kgf´cm, 14 ft´lbf)
(d) Disconnect the 2 rings and remove the exhaust front pipe.
15. REMOVE STARTER
Disconnect the connector and wire and remove the starter.
16. DISCONNECT SPEEDOMETER CABLE
17. REMOVE ENGINE REAR MOUNTING INSULATOR
Remove the 6 bolts and insulator.
Torque:
Bolt A: 78 N´m (800 kgf´cm, 58 ft´lbf)
Bolt B: 64 N´m (650 kgf´cm, 47 ft´lbf)
Bolt C: 90 N´m (920 kgf´cm, 67 ft´lbf)
18. DISCONNECT ENGINE LEFT MOUNTING BRACKET
FROM ENGINE LEFT MOUNTING INSULATOR
Remove the 2 bolts.
Torque: 48 N´m (490 kgf´cm, 36 ft´lbf)
19. JACK UP TRANSAXLE SLIGHTLY
Using a transmission jack, support the transaxle.
20. REMOVE TRANSAXLE LOWER SIDE MOUNTING
BOLT
Remove the 4 bolts.
Torque:
14 mm head: 46 N´m (470 kgf´cm, 34 ft´lbf)
10 mm head: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
21. REMOVE TRANSAXLE
Lower the engine left side and remove the transaxle from the
engine.
HINT:

Align the input shaft with the clutch disc and install the
transaxle to the engine.

Install and torque the 7 bolts.
Torque:
Upper side mounting bolts: (See step 7)
Lower side mounting bolts: (See step 20)

AX08M-03
Q07634
RH Drive Shaft

Snap
RingSpeedometer
Cable
Rear Engine
Mounting InsulatorAir Cleaner
Assembly

Snap RingTie Rod End
LH Drive Shaft
Nut Cap Plug for Governor Pressure Test
Oxygen Sensor
Front Exhaust Pipe Torque Converter
Clutch
Clip
Control Cable

Gasket
Compression Spring
Engine Under Cover
Cotter Pin Starter

Gasket
Clamp x 6
Plug for Line
Pressure Test

Non-reusable partx 5
Converter
Cover
- AUTOMATIC TRANSAXLE (A132L)AUTOMATIC TRANSAXLE UNIT
AX-25
777 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE UNIT
COMPONENTS

AX08N-03
Q06547
Q06548
Q07635
Q08079
AX-26
- AUTOMATIC TRANSAXLE (A132L)AUTOMATIC TRANSAXLE UNIT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE BATTERY
2. REMOVE AIR CLEANER ASSEMBLY
3. REMOVE THROTTLE CABLE
4. REMOVE UPPER SIDE MOUNTING BOLTS
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
5. REMOVE STARTER
(a) Disconnect the cable and connector.
(b) Remove the starter with the 2 bolts.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
6. REMOVE GROUND CABLES AND BRACKET
7. INSTALL ENGINE SUPPORT FIXTURE
8. RAISE VEHICLE
9. REMOVE ENGINE UNDER COVER
10. REMOVE LH AND RH DRIVE SHAFTS
(See page SA-18)
11. DISCONNECT SPEEDOMETER CABLE
12. DISCONNECT CONTROL CABLE
(a) Remove the clip from the control cable.
(b) Disconnect the control cable from the lever.
Torque: 12 N´m (120 kgf´cm, 9 ft´lbf)
13. DISCONNECT PARK/NEUTRAL POSITION SWITCH
CONNECTOR
14. DISCONNECT OIL COOLER HOSE FROM PIPE
15. REMOVE FRONT EXHAUST PIPE
(a) Disconnect the oxygen sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(b) Remove the bolts and springs from the exhaust manifold
and front exhaust pipe.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
(c) Remove the clamp.
Torque: 19 N´m (190 kgf´cm, 14 ft´lbf)

AX086-04
Q07636
RH Drive ShaftStarterAir Cleaner
Assembly
Speedometer Cable
Rear Engine Mounting Insulator
Plug for Governor
Pressure Test
Tie Rod End

Snap Ring
LH Drive Shaft

Gasket
Clamp
Nut Cap

Cotter Pin O/D Solenoid
Connector
Snap
Ring
x6
Hole Plug
Torque Converter
Clutch
Clip
Control
Cable
Plug for Line Pressure Test
Oxygen Sensor

Gasket
Front Exhaust Pipe
Compression Spring
Engine Under Cover

Non-reusable part
- AUTOMATIC TRANSAXLE (A242L)AUTOMATIC TRANSAXLE UNIT
AX-29
811 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE UNIT
COMPONENTS