check engine light TOYOTA TERCEL 1996 Service User Guide

FI7130
Vehicle Speed
50 - 65 km/h
(31 - 40 mph)
Idling
IG SW OFF
1 - 3 min.
1 min.
Time
(1) (2)
(3)(4)
(5)
- DIAGNOSTICSENGINE
DI-41
1996 TERCEL (RM440U)
DTC P0130 Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-38.
DTC No.DTC Detection ConditionTrouble Area
P0130
Voltage output of oxygen sensor remains at 0.4 V or
more, or 0.55 V or less, during idling after the engine is
warmed up (2 trip detection logic)
Oxygen sensor

Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The oxygen sensor's output voltage and the short-term fuel trim value can be read using the OBD II scan
tool or TOYOTA hand-held tester.
WIRING DIAGRAM
Refer to page DI-38.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand-held tester to the DLC3.
(2) Switch the TOYOTA hand-held tester from normal mode to check mode (See page DI-3).
(3) Start the engine and warm it up with all accessory switches OFF.
(4) Drive the vehicle at 50 - 65 km/h (31 - 40 mph) for 1 - 3 minutes to warm up the oxygen sensor.
(5) Idle the engine for 1 minute.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the malfunction will not be possible.
If you do not have a TOYOTA hand-held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI1EB-08

P20769
Vehicle Speed
70 - 90 km/h
(43 - 56 mph)
Idling
IG SW OFF(a)(b)(c)
(d)
(e)(f)
(g)
Warm up 3 - 5 min. 2 min. 3 - 5 min. 2 min.
Time DI-66
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
SYSTEM CHECK DRIVING PATTERN
(a) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(b) Start the engine and warm it up with all accessories switched OFF.
(c) Run the vehicle at 70 - 90 km/h (43 - 56 mph) for 3 minutes or more.
(d) Idle the engine for about 2 minutes.
(e) Stop at safe place and turn the ignition switch OFF.
(f) Start the engine and do steps (c) and (d) again.
(g) Check the READINESS TESTS mode on the OBD II scan tool or TOYOTA hand-held tester. If COMPL
is displayed and the MIL does not light up, the system is normal. If INCMPL is displayed and the MIL
does not light up, run the vehicle again and check it.
HINT:
INCMPL is displayed when either condition (h) or (i) exists.
(h) The system check is incomplete.
(i) There is a malfunction in the system.
If there is a malfunction in the system, the MIL will light up after steps (b) to (f) above are done.
INSPECTION PROCEDURE
HINT:

If DTC P0105 and/or P0106 and P0401 are output simultaneously, perform troubleshooting of DTC
ºP0105º first.

If DTC P0401 and P0402 are output simultaneously, perform troubleshooting of DTC P0402 first.

FI7132
Engine Speed
2,500 - 3,000 rpm
Idling
IG SW OFF
Warmed up3 min. or soCheckTime (a)(c)
(d)
(b)
FI6514
OX Signal Waveform (Oscilloscope)
1.0 V
0 V
200 m sec. /Division
DI-74
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
CONFIRMATION ENGINE RACING PATTERN
(a) Connect the TOYOTA hand-held tester to the DLC3, or connect the probe of the oscilloscope between
terminals OX1, OX2 and E1 of ECM.
(b) Start engine and warm it up with all accessories switched OFF until engine coolant temperature is
stable.
(c) Race the engine at 2,500 - 3,000 rpm for about 3 minutes.
(d) After confirming that the waveform of the oxygen sensor, bank 1 sensor 1 (OX1), oscillate around 0.5
V during feedback to the ECM, check the waveform of the heated oxygen sensor, bank 1 sensor 2
(OX2).
HINT:
If there is a malfunction in the system, the waveform of the
heated oxygen sensor, bank 1 sensor 2 (OX2), is almost the
same as that of the oxygen sensor, bank 1 sensor 1 (OX1), on
the left.
There are some cases where, even though a malfunction ex-
ists, the MIL may either light up or not light up.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P0420) being output?
YES Go to relevant DTC chart.
NO
2 Check heated oxygen sensor (bank 1 sensor 2) (See page DI-44).

R13006
DLC1
E
1
TcTs
BR3904
0.13 sec. 0.13 sec.
ON
OFF
BR3893
Malfunction Code (Example Code 72, 76)
72 67
ON
OFF
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.1.5 sec.
2.5 sec.4 sec.
Repeat
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-1 13
1996 TERCEL (RM440U)
2. SPEED SENSOR SIGNAL CHECK
(a) Check the speed sensor signal.
(1) Turn the ignition switch OFF.
(2) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843-18020
(3) Start the engine.
(4) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI-138).
(5) Drive the vehicle faster than 45 km/h (28 mph) for
several seconds.
(6) Stop the vehicle.
(7) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843-18020
(8) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTCs shown on the next page.

If every sensor is normal, a normal code is output (A cycle
of 0.25 sec. ON and 0.25 sec. OFF is repeated).

If 2 or more malfunctions are indicated at the same time,
the lowest numbered code will be displayed 1st.
(9) After doing the check, disconnect terminals Ts and
E
1, and Tc and E1 of the DLC1, and turn ignition
switch OFF.

F00414
24ABS ECU
AA123DLC1
Ts
16
EC
E1TsL
B-RAEA13
B-RL12 V
J/C
J1
R13006
E1
DLC1
Tc
- DIAGNOSTICSANTI-LOCK BRAKE SYSTEM
DI-143
1996 TERCEL (RM440U)
Ts Terminal Circuit
CIRCUIT DESCRIPTION
The sensor check circuit detects abnormalities in the speed sensor signal which cannot be detected with
the DTC check.
Connecting terminals Ts and E
1 of the DLC1 in the engine compartment starts the check.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminals Ts and E1 of DLC1.
CHECK:
(a) Turn the ignition switch ON.
(b) Measure the voltage between terminals Ts and E
1 of the
DLC1.
OK:
Voltage: 10 - 14 V
OK If ABS warning light does not blink even after Ts
and E
1 are connected, ECU may be defective.
NG
DI4M1-02

DI4MZ-01
THEFT DETERRENT SYSTEM Check Sheet
Inspector 's name:
Customer 's Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading / /km
Mile
Weather Conditions
When Problem
Occurred Frequency Problem OccursWeather
Outdoor temperature
/ /

Constant
Sometimes ( Times per day, month)

Once only Brought in

Theft deterrent system cannot be set.

Indicator light does not flash when the theft deterrent system is set.
(It stays on or does not light at all.)

Theft deterrent system
does not operate.
When unlocked using the
door lock knob.

When the engine hood is
opened.

System cannot be
canceled once set.
When door is unlocked using key or wireless door lock control system.

When the key is inserted in the ignition key cylinder and turned to ACC or ON
position.
(However, only when the system has never operated)

When the luggage compartment door is opened with the key.

System cannot be
canceled during warning
operation.
When door is unlocked using key or wireless door lock control system.

When the key is inserted in the ignition key cylinder and turned to ACC or ON
position.

Warning operation starts when the system is set and the door or luggage compartment door is opened with
the key.

Others.
Date Problem First Occurred

Fine
Cloudy
Rainy
Snowy

Various/Others

Hot
Warm
Cool

Cold (Approx. 5F ( 5C))
Problem Symptom
Malfunction

Horns only

Theft deterrent horn only

Headlights only

Taillights only

Starter cut only

Door lock operation only
DI-216
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
1996 TERCEL (RM440U)
CUSTOMER PROBLEM ANALYSIS CHECK

DI4N0-02
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
DI-217
1996 TERCEL (RM440U)
PRE-CHECK
1. SETTING OF THE THEFT DETERRENT SYSTEM
Setting Conditions
(a) Close all the doors.
(b) Close the engine hood and luggage compartment door.
(c) Remove the ignition key from the ignition key cylinder.
Setting Operation
When any of the following operations (a), (b) or (c) is performed, the theft deterrent indicator light will light
up as described.
(1) Lock the left or right front door using the key
(All doors are locked by key-interlinked lock operation).
(2) Lock all the doors using the wireless door lock control system.
(3) With the rear doors locked and with one of the front doors locked, lock the other front door without
using the key (keyless door lock).
Elapsed time after operationIndicator light
Within about 30 secondsLight up
After about 30 secondsBlinks *1
*1: 1 sec. or, 1 sec. off
HINT:
When the theft deterrent system is set, doors cannot be locked or unlocked with the door lock control switch
and the luggage compartment door cannot be unlocked with the luggage compartment door opener switch.
2. CANCELING OF THE THEFT DETERRENT SYSTEM IN THE SET CONDITION
Check if the theft deterrent indicator light is blinking.
Canceling Operation
When any of the following operations (a), (b), (c) or (d) is performed, the theft deterrent system is canceled
and indicator light will go off.
Condition
(1) Unlock the left or right front door using the key.
(2) Unlock all the doors using the wireless door lock control system.
(3) Insert the ignition key in the ignition key cylinder and turn it to the ACC or ON position
(This is operative only when the theft deterrent system has never operated).
(4) Unlock the luggage compartment door with the key. *1
*1: The theft deterrent system is temporarily canceled only while the luggage compartment door is open.
Approximately 2 seconds after the luggage compartment door is closed, the theft deterrent system is reset.
3. CHECK OF THE THEFT DETERRENT SYSTEM OPERATION
Check if the theft deterrent indicator light is blinking.
When any of the following operations (a) or (b) is performed, the system sounds the horns and theft deterrent
horn and flashes the headlights and taillights for about one minute to alert. At the same time, the system
disconnects the starter motor circuit and locks all doors (if all doors are not locked, the system repeats door
locking operation every 2 seconds during the one minute alert time).
(1) Open the engine hood using the engine hood opener lever.
(2) Unlock any of the front or rear doors without key operation.

P19787
SST(A)
SST(B)
Spark Plug Side
Z07669
B
A
BB
A
B
- ENGINE MECHANICALVALVE CLEARANCE
EM-5
426 Author
: Date
:
1996 TERCEL (RM440U)
(b) Turn the crankshaft pulley 1 revolution (360°) and align
its groove with the timing mark º0º of the No.1 timing belt
cover.
(c) Check only the valves indicated as shown. Measure the
valve clearance (See procedure in step (a)).
6. ADJUST VALVE CLEARANCE
(a) Remove the adjusting shim.
(1) Turn the crankshaft to position the cam lobe of the
camshaft on the adjusting valve points upward.
(2) Position the notch of the valve lifter so that the shim
can be removed with a small screwdriver as shown
in the illustration.
(3) Using SST (A), press down the valve lifter and place
SST (B) between the camshaft and valve lifter
flange. Remove SST (A).
SST 09248-55040 (09248-05410, 09248-05420)
HINT:

Apply SST (B) at slight angle on the side marked with º9º,
at the position shown in the illustration.

Set SST (A) at position A, if position A is too narrow, at
position B, as shown in the illustration.
(4) Remove the adjusting shim with a small screwdriver
and magnetic finger.

P19552
TOYOTA Hand-Held Tester
DLC3EM0K9-03
P20244
- ENGINE MECHANICALIGNITION TIMING
EM-9
430 Author
: Date
:
1996 TERCEL (RM440U)
IGNITION TIMING
INSPECTION
1. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
2. CONNECT TOYOTA HAND-HELD TESTER OR OBDII
SCAN TOOL
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand-held tester or OBDII scan
tool to the DLC3.
(c) Please refer to the TOYOTA hand-held tester or OBDII
scan tool operator's manual for further details.
3. CONNECT TIMING LIGHT
4. INSPECT IGNITION TIMING
(a) Using SST, connect terminals TE1 and E1 of the DLC1.
SST 09843-18020
(b) Using a timing light, check the ignition timing.
Ignition timing:
10° BTDC @ idle
(w/ Cooling fan OFF and transmission in neutral
position)
(c) Remove the SST from the DLC1.
SST 09843-18020
5. FURTHER CHECK IGNITION TIMING
Check that the ignition timing advances.
Ignition timing:
7 - 17° BTDC @ idle
(w/ Cooling fan OFF and transmission in neutral posi-
tion)
HINT:
The timing mark moves in a range between 7° and 17°.
6. DISCONNECT TIMING LIGHT
7. DISCONNECT TOYOTA HAND- HELD TESTER OR
OBDII SCAN TOOL

EM1OD-01
P20154
Oil Pan
P20153
Ground Strap
P20536
Timing Mark
P20159
EM-12
- ENGINE MECHANICALTIMING BELT
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. w/ A/C and/or w/ PS:
REMOVE DRIVE BELT
3. REMOVE GENERATOR DRIVE BELT
4. SLIGHTY JACK UP ENGINE
5. SLIGHTLY JACK UP ENGINE
Raise the engine enough to remove the weight from the engine
mounting on the right side.
6. REMOVE RH ENGINE MOUNTING INSULATOR
(a) Remove the bolt and disconnect the ground strap.
(b) Remove the through bolt, 2 bolts, nut and mounting insu-
lator.
7. REMOVE NO.2 TIMING BELT COVER
Remove the 4 bolts, timing belt cover and gasket.
8. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with the
timing mark º0º of the No.1 timing belt cover.
NOTICE:
Always turn the crankshaft clockwise.
(b) Check that the hole of the camshaft timing pulley on the
side with the 5E mark is aligned with the timing mark of the
No.1 bearing cap.
If not, turn the crankshaft pulley 1 complete revolution (360°).
9. w/ A/C and/or w/ PS:
REMOVE NO.2 CRANKSHAFT PULLEY
Remove the 4 bolts and No.2 crankshaft pulley.