brake fluid TOYOTA TERCEL 1996 Service Owner's Manual

BR0RM-04
F03521
SST
Gasket
N00744
SST
BR1728 BR0021
BR-18
- BRAKEBRAKE BOOSTER ASSEMBLY
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL BRAKE BOOSTER
(a) Install the booster and a new gasket.
(b) Install the clevis to the operating rod.
(c) Install and torque the booster installation nuts.
Torque: 14 N´m (145 kgf´cm, 10 ft´lbf)
(d) Insert the clevis pin into the clevis and brake pedal, and
install the clip to the clevis pin.
(e) Install the pedal return spring.
(f) Install the No.1 brake line clamp to the body.
(g) Install the No.2 brake line clamp to the body.
2. ADJUST LENGTH OF BOOSTER PUSH ROD
(a) Install the gasket on the master cylinder.
(b) Set SST on the gasket, and lower the pin until its tip slight-
ly touches the piston.
SST 09737-00010
(c) Turn SST upside down, and set it on the booster.
SST 09737-00010
(d) Measure the clearance between the booster push rod
and pin head (SST).
Clearance: 0 mm (0 in.)
(e) Adjust the booster push rod length until the push rod
slightly touches the pin head.
HINT:
When loosening the push rod nut, depress the brake pedal
enough so that the push rod sticks out.
3. INSTALL MASTER CYLINDER
4. CONNECT VACUUM HOSE TO BRAKE BOOSTER
5. FILL BRAKE RESERVOIR WITH BRAKE FLUID AND
BLEED BRAKE SYSTEM (See page BR-4)
6. CHECK FOR LEAKS

N00746
BR-22
- BRAKEFRONT BRAKE PAD
1996 TERCEL (RM440U)
(e) Install inner pad with the pad wear indicator plate facing
upward.
(f) Install outer pad.
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or the disc.
8. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the piston with a hammer handle or an equiva-
lent.
HINT:
If the piston is difficult to push in, loosen the bleeder plug and
push in the piston while letting some brake fluid escape.
(c) Install the caliper.
(d) Install and torque the 2 installation bolts.
Torque: 25 N´m (255 kgf´cm, 18 ft´lbf)
9. INSTALL FRONT WHEEL
10. CHECK THAT FLUID LEVEL IS AT MAX LINE

BR0RQ-05
BR4220
BR-24
- BRAKEFRONT BRAKE CALIPER
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
Install the flexible hose lock securely in the lock hole in the cali-
per.
(b) Use a container to catch the brake fluid as it drains out.
2. REMOVE CALIPER
Remove the 2 installation bolts, and caliper.
Torque: 25 N´m (255 kgf´cm, 18 ft´lbf)
3. REMOVE THESE PARTS:
(a) 2 brake pads with anti-squeal shims.
(b) 4 pad support plates.

BR0RU-04
BR-28
- BRAKEFRONT BRAKE CALIPER
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-24).
1. AFTER INSTALLATION, FILL BRAKE RESERVOIR WITH BRAKE FLUID AND BLEED BRAKE
SYSTEM (See page BR-4)
2. CHECK FOR LEAKS

BR4387
BR3027
SST
BR0370
- BRAKEREAR DRUM BRAKE
BR-31
1996 TERCEL (RM440U)
(d) Using pliers, disconnect the parking brake cable from the
parking brake lever and remove the rear shoe.
6. REMOVE AUTOMATIC ADJUSTING LEVER AND
PARKING BRAKE LEVER
(a) Remove the E-ring.
(b) Remove the automatic adjusting lever.
(c) Remove the C-washer.
(d) Remove the parking brake lever.
7. REMOVE WHEEL CYLINDER
(a) Using SST, disconnect the brake line. Use a container to
catch the brake fluid.
SST 09751-3601 1
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
(b) Remove the 2 bolts and the wheel cylinder.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
8. DISASSEMBLE WHEEL CYLINDER
Remove the these parts from the wheel cylinder.

2 boots

2 pistons

2 piston cups

Spring

BR0RY-04
BR4247
N00755
BR0376 BR0412
N00756 BR0394 BR0413
- BRAKEREAR DRUM BRAKE
BR-33
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page
BR-30).
1. AFTER INSTALLATION, FILL BRAKE RESERVOIR
WITH BRAKE FLUID, BRAKE SYSTEM
NOTICE:
Apply lithium soap base glycol grease and high tempera-
ture grease to the parts indicated by the arrows (See page
BR-29).
2. CHECK OPERATION OF AUTOMATIC ADJUSTING
MECHANISM
(a) Move the parking brake lever of the rear shoe back and
forth. Check that the adjuster turns.
If the adjuster does not turn, check for incorrect installation of
the rear brake.
(b) Adjust the adjuster length to the as short as possible.
(c) Install the brake drum.
(d) Pull the parking brake lever all the way up until a clicking
sound can no longer be heard.
3. CHECK CLEARANCE BETWEEN BRAKE SHOES AND
DRUM
(a) Remove the brake drum (See page SA-39).
(b) Measure the brake drum inside diameter and diameter of
the brake shoes. Check that the difference between the
diameters is the correct shoe clearance.
Shoe clearance: 0.6 mm (0.024 in.)
If incorrect, check the parking brake system.
(c) Install the brake drum (See page SA-42).

BR0RZ-06
R04666
SSTSST BR-34
- BRAKEPROPORTIONING VALVE (P VALVE)
908 Author
: Date
:
1996 TERCEL (RM440U)
PROPORTIONING VALVE (P VALVE)
ON-VEHICLE INSPECTION
1. INSTALL LSPV GAUGE (SST)
SST 09709-29018
2. BLEED AIR FROM FLUID PRESSURE GAUGE
3. RAISE FRONT BRAKE CALIPER PRESSURE AND CHECK REAR WHEEL CYLINDER PRES-
SURE
w/o ABS
Front brake caliper pressureRear wheel cylinder pressure
2,452 kPa (25 kgf/cm2, 356 psi)2,452 kPa (25 kgf/cm2, 356 psi)
7,845 kPa (80 kgf/cm2, 1,138 psi)3,805 kPa (38.8 kgf/cm2, 552 psi)
w/ ABS
Front brake caliper pressureRear wheel cylinder pressure
2,942 kPa (30 kgf/cm2, 427 psi)2,942 kPa (30 kgf/cm2, 427 psi)
7,845 kPa (80 kgf/cm2, 1,138 psi)4,168 kPa (42.5 kgf/cm2, 604 psi)
When inspecting the fluid pressure, inspect the left front and right rear together, and the right front and left
rear together.
If the rear wheel cylinder pressure is incorrect, replace the P valve assembly.
4. BLEED BRAKE SYSTEM (See page BR-4)
5. CHECK FOR LEAKS

BR0S3-06
BR-40
- BRAKEABS ACTUATOR
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-39).
AFTER INSTALLATION, FILL BRAKE RESERVOIR WITH BRAKE FLUID, BLEED BRAKE SYSTEM (See
page BR-4) AND CHECK FOR LEAKS

BE-4
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Taillight does not light up. (Headlight does not light up)
1. Light Control Switch
2. Headlight Bulb
3. Wire HarnessBE-16
-
-
Headlight does not light up with light control SW in HEAD.
1. Light Control Switch
2. D.R.L. Main Relay
3. D.R.L. No.4 Relay (R/B No.5)
4. Daytime Resistor
5. Wire HarnessBE-16
BE-16
BE-16
BE-16
-
Headlight does not go out with light control SW in OFF.1. Headlight Control Relay (Engine Room R/B)
2. Wire HarnessBE-16
-
Taillight does not light up with light control SW in TAIL.
1. Taillight Control Relay (I/P J/B)
2. Light Control Switch
3. Wire HarnessBE-16
BE-16
-
Taillight does not go out with light control SW in OFF.
1. Taillight Control Relay (I/P J/B)
2. Light Control Switch
3. Wire HarnessBE-16
BE-16
-
Headlight do not light up with engine running and light control SW
in OFF.
1. DOME Fuse (Engine Room R/B)
2. ECU-IG Fuse (I/P J/B)
3. DRL Fuse (Engine Room R/B)
4. D.R.L. Main Relay
5. D.R.L. No.4 Relay (R/B No.5)
6. Daytime Resistor
7. Wire Harness
8. Generator L Terminal
9. Parking Brake Switch
10.Brake Fluid Level Warning Switch-
-
-
BE-16
BE-16
BE-16
-
-
BE-38
BE-38
TURN SIGNAL AND HAZARD WARNING SYSTEM
TroubleParts nameSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-22
BE-22
-
No of blinks for Hazard.
(Turn is abnormal)1. Bulb
2. Turn Signal Flasher
3. Wire Harness-
BE-22
-
Hazard warning light does not light up.
(Turn signal is normal)1. HAZ-HORN Fuse (Engine Room R/B)
2. Wire Harness-
-
Hazard waning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-22
-
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (Engine Room R/B)
3. Turn Signal Switch
4. Wire HarnessBE-1 1
-
BE-22
-
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (Engine Room R/B)
2. Turn Signal Switch
3. Wire Harness-
BE-22
-

BE-6
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TERCEL (RM440U) Washer fluid does not operate.
1. Washer Hose and Nozzle-

At wiper switch HI position, the wiper blade is in contact with the
body.

When the wiper switch is OFF, the wiper blade does not retract
or the retract position is wrong.
1. *1 Wiper Switch
2. Wire harnessBE-30
-
*1: Inspect wiper arm and blade set position
COMBINATION METER (METER, GAUGES AND ILLUMINATION)
TroubleParts nameSee page
Tachometer, Fuel Gauge and Engine Coolant Temperature Gauge
do not operate.3. GAUGE Fuse (Engine Room R/B)
4. Meter Circuit
5. Wire Harness-
BE-35
-
Speedometer does not operate.
1. Vehicle Speed Sensor
2. Meter Circuit
3. Wire HarnessBE-38
BE-35
-
Tachometer does not operate.
1. Igniter
2. ECM
3. Meter Circuit
4. Wire Harness-
-
BE-35
-
Fuel Gauge does not operate or operate abnormally.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
Engine Coolant Temperature Gauge does not operate or operate
abnormally.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE-38
BE-38
BE-35
-
All illumination lights do not light up.
1. TAIL Fuse (I/P J/B)
2. Light Control Rheostat
3. Meter Circuit
4. Wire Harness-
BE-38
BE-35
-
Only one illumination light does not light up.1. Bulb
2. Meter Circuit-
BE-35
COMBINATION METER (WARNING LIGHTS)
TroubleParts nameSee page
Warning lights do not light up.
(Except Discharge, SRS and Door Open)
1. Bulb
2. GAUGE Fuse (I/P J/B)
3. Ignition Switch
4. Meter Circuit
5. Wire Harness-
-
BE-1 1
BE-35
-
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness-
BE-38
BE-38
-
BE-35
-
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Retractor Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness-
BE-38
BE-38
BE-35
-