check engine TOYOTA TERCEL 1996 Service Service Manual

A15693
- DIAGNOSTICSENGINE
DI-39
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Connect OBD II scan tool or TOYOTA hand-held tester and read value for volt-
age output of heated oxygen sensor.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up the engine to the normal operating temperature.
CHECK:
Read the voltage output of the heated oxygen sensor (bank 1 sensor 1) when the engine is suddenly raced.
HINT:
Perform quick racing to 4,000 rpm 3 times using accelerator pedal.
OK:
Heated oxygen sensor output a RICH signal (0.45 V or more) at least once.
OK Check and replace ECM (See page IN-26).
NG
2 Check for open and short in harness and connector between ECM and oxygen
sensor (See page IN-26).
NG Repair or replace harness or connector.

FI7130
Vehicle Speed
50 - 65 km/h
(31 - 40 mph)
Idling
IG SW OFF
1 - 3 min.
1 min.
Time
(1) (2)
(3)(4)
(5)
- DIAGNOSTICSENGINE
DI-41
1996 TERCEL (RM440U)
DTC P0130 Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-38.
DTC No.DTC Detection ConditionTrouble Area
P0130
Voltage output of oxygen sensor remains at 0.4 V or
more, or 0.55 V or less, during idling after the engine is
warmed up (2 trip detection logic)
Oxygen sensor

Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The oxygen sensor's output voltage and the short-term fuel trim value can be read using the OBD II scan
tool or TOYOTA hand-held tester.
WIRING DIAGRAM
Refer to page DI-38.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand-held tester to the DLC3.
(2) Switch the TOYOTA hand-held tester from normal mode to check mode (See page DI-3).
(3) Start the engine and warm it up with all accessory switches OFF.
(4) Drive the vehicle at 50 - 65 km/h (31 - 40 mph) for 1 - 3 minutes to warm up the oxygen sensor.
(5) Idle the engine for 1 minute.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the malfunction will not be possible.
If you do not have a TOYOTA hand-held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI1EB-08

DI-42
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check for open and short in harness and connector between ECM and oxygen
sensor (See page IN-26).
NG Repair or replace harness or connector.
OK
2 Check for oxygen sensor data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the oxygen sensor output voltage and short-term fuel trim.
RESULT:
PatternOxygen sensor output voltageShort-term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about +20 %
2Rich condition (Changes at 0.4 V or more)Changes at about -20 %
3Except 1 and 2
1, 2 Check fuel trim system (See page DI-49).
3

P18349
- DIAGNOSTICSENGINE
DI-43
1996 TERCEL (RM440U)
3 Check output voltage of oxygen sensor during idling.
PREPARATION:
Warm up the oxygen sensor with the engine at 2,500 rpm for approximately 90 seconds.
CHECK:
Using the OBD II scan tool or TOYOTA hand-held tester, read the output voltage of the oxygen sensor during
idling.
OK:
Oxygen sensor output voltage:
Alternates repeatedly between approx. 0.4 V and approx. 0.55 V (See these table):
OK Perform confirmation driving pattern.
(See page DI-41)
NG
Replace oxygen sensor.

- DIAGNOSTICSENGINE
DI-45
1996 TERCEL (RM440U)
DTC P0136 Heated Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 2)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-38.
DTC No.DTC Detection ConditionTrouble Area
P0136
Voltage output of the heated oxygen sensor (bank 1 sensor 2)
remains at 0.4 V or more, or 0.5 V or less when the vehicle is
driven at 50 km/h (31 mph) or more after the engine is warmed
up
(2 trip detection logic).

Heated oxygen sensor
HINT:
Sensor 2 refers to the sensor farther away from the engine body.
WIRING DIAGRAM
Refer to page DI-38.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P0136) being output?
YES Go to relevant DTC chart.
NO
2 Check for open and short in harness and connector between ECM and heated
oxygen sensor (See page IN-26).
NG Repair or replace harness or connector.
OK
DI00Y-21

DI-46
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
3 Check output voltage of heated oxygen sensor (bank 1 sensor 2).
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) After warming up the engine, race the engine at 2,500 rpm for 3 minutes.
CHECK:
Read the output voltage of the heated oxygen sensor (bank 1 sensor 2) when racing the engine after 3 min-
utes have elapsed.
OK:
Heated oxygen sensor output voltage: Alternates from 0.4 V or less to 0.5 V or more.
OK Check that each connector is properly
connected.
NG
Replace heated oxygen sensor.

A15695
- DIAGNOSTICSENGINE
DI-47
1996 TERCEL (RM440U)
DTC P0135 Heated Oxygen Sensor Heated Circuit
Malfunction (Bank 1 Sensor 1)
DTC P0141 Heated Oxygen Sensor Heated Circuit
Malfunction (Bank 1 Sensor 2)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-38.
DTC No.DTC Detection ConditionTrouble Area
P0135
When the heater operates, heater current exceeds 2 A
(2 trip detection logic)
Open or short in heater circuit of heated oxygen sensor
Htd htP0135
P0141Heater current of 0.25 A or less when the heater
operates (2 trip detection logic)
Heated oxygen sensor heater

ECM
WIRING DIAGRAM
Refer to page DI-38.
INSPECTION PROCEDURE
1 Check voltage between terminal HT1, HT2 of ECM connector and body ground.
PREPARATION:
(a) Remove the lower finish panel.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal HT1, HT2 of the ECM
connector and the body ground.
OK:
Voltage: 9 - 14 V
OK Check and replace ECM (See page IN-26).
NG
2 Check resistance of heated oxygen sensor heater (See page MF-53).
NG Replace heated oxygen sensor.
OK
DI1ED-1 1

DI-48
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
Check and repair harness or connector be-
tween EFI main relay and heated oxygen sen-
sor and ECM.

DI-50
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
INSPECTION PROCEDURE
1 Check air induction system (See page MF-1).
NG Repair or replace.
OK
2 Check for heated oxygen sensor data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the oxygen sensor output voltage and short-term fuel trim.
RESULT:
PatternOxygen sensor output voltageShort-term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about + 20 %
2RIch condition (Changes at 0.4 V or more)Changes at about - 20 %
3Except 1 and 2
3 Check for oxygen sensor
(See page DI-41).
1, 2
3 Check fuel pressure (See page MF-1).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter. (See page MF-5)
OK

- DIAGNOSTICSENGINE
DI-51
1996 TERCEL (RM440U)
4 Check injector injection (See page MF-19).
NG Replace injector.
OK
5 Check manifold absolute pressure sensor and engine coolant temp. sensor
(See page DI-20, DI-28).
NG Repair or replace.
OK
6 Check for spark and ignition (See page IG-1).
NG Repair or replace.
OK
Check and replace ECM (See page IN-26).