torque TOYOTA TERCEL 1996 Service Service Manual

SS0LL-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A132L)
SS-29
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug4950036
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C
Bolt D7.4
25
46
6475
250
470
65065 in.´lbf
18
34
47
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

SS0LI-04
SS-30
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
160 Author
: Date
:
1996 TERCEL (RM440U)
AUTOMATIC TRANSAXLE (A242L)
SERVICE DATA
Governor pressure Vehicle speed reference
30 km/h (19 mph)
60 km/h (37 mph)
90 km/h (56 mph)
59 - 137 kPa (0.6 - 1.4 kgf/cm2, 9 - 20 psi)
196 - 275 kPa (2.0 - 2.8 kgf/cm2, 28 - 40 psi)
363 - 441 kPa (3.7 - 4.5 kgf/cm2, 53 - 64 psi)
Line pressure (Wheel locked)
Engine Idling D position
R position
AT stall (Throttle valve fully opened) D position
R position
373 - 422 kPa (3.8 - 4.3 kgf/cm2, 54 - 61 psi)
549 - 706 kPa (5.6 - 7.2 kgf/cm2, 80 - 102 psi)
902 - 1,049 kPa (9.2 - 10.7 kgf/cm2, 131 - 152 psi)
1,638 - 1,902 kPa (16.7 - 19.4 kgf/cm2, 238 - 276 psi)
Engine stall revolution D and R positions2,300 ± 200 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF) N position750 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)
Between boot end face and inner cable stopper
0 - 1 mm (0 - 0.04 in.)
Torque converter clutch installation distance
Drive plate runoutMax.
Torque converter clutch runout Max.More than 13.0 mm (0.512 in.)
0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
Differential oil seal drive in depth LH side
RH side5.3 ± 0.5 mm (0.209 ± 0.020 in.)
3.1 ± 0.5 mm (0.122 ± 0.020 in.)
Speedometer driven gear oil seal drive in depth25.0 mm (0.98 in.)
Shift Point
D position
Throttle valve fully opened 1 "2
2 " 3
3 " 2
2 " 1
Throttle valve fully closed 3 O/D
L position
Throttle valve fully closed 2 " 1
45 - 61 km/h (28 - 38 mph)
89 - 106 km/h (55 - 66 mph)
83 - 102 km/h (52 - 63 mph)
83 - 43 km/h (19 - 27 mph)
19 - 33 km/h (12 - 21 mph)
44 - 56 km/h (27 - 35 mph)
Lock-up point
D position
Throttle valve fully closed Lock-up ON
Lock-up OFF
65 - 76 km/h (40 - 47 mph)
61 - 72 km/h (38 - 45 mph)

SS0LJ-04
- SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A242L)
SS-31
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Oil pan drain plug1717513
Oil pan4.95043 in.´lbf
Detent spring101007
Valve body x Oil pipe clamp101007
Valve body x Oil strainer101007
Valve body x Apply pipe bracket101007
Valve body x Transaxle101007
Park/neutral position switch x Transaxle case (bolt)5.45548 in.´lbf
Park/neutral position switch (nut)6.97061 in.´lbf
Transaxle control shaft lever x Park/neutral position switch131309
Transaxle control shaft lever x Transaxle control cable121209
Drive plate x Crankshaft8890065
Torque converter clutch x Drive plate2728020
Starter3940029
Transaxle housing x Engine (upper side)6465047
Transaxle housing x Engine (lower side) Bolt A
Bolt B
Bolt C7.4
64
4675
650
47065 in.´lbf
47
34
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Oxygen sensor4445032
Exhaust pipe clamp1919014
LH engine mounting x Body4949036
Engine rear mounting bracket x Engine rear mounting insulator6565048
Engine rear mounting insulator x Body Bolt A
Bolt B80
92800
92059
69

SS0LO-07
SS-32
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
162 Author
: Date
:
1996 TERCEL (RM440U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire inflationTire sizeCold tire inflation
pressure
Tire size
155SR13 ASFront240 kPa (2.4 kgf/cm2, 34 psi)ressure 155SR13 AS Front
Rear
240 kPa (2.4 kgf/cm, 34 si)
225 kPa (2.25 kgf/cm2, 32 psi)
Vehicle heightTire size
155SR13 ASFront
Rear
187.9 mm (7.40 in.)
253.2 mm (9.97 in.)
Front wheel align-
mentToe-in (Total)
Tie rod end left-right error0.1° ± 0.2° (1 ± 2 mm, 0.04 ± 0.08 in.)
1.5 mm (0.059 in.) or less
ment
Camber
Left-right error-0°20' ± 45'
45' or less
Caster
Left-right error1°20' ± 45'
45' or less
Steering axis inclination
Left-right error12°10' ± 45'
45' or less
Wheel angle Inside wheel
Outside wheel35°55' ± 2°
32°10' (Reference)
Rear wheel align-Toe-in (Total)0.3° ± 0.3° (3 ± 3 mm, 0.12 ± 0.12 in.)Rear wheel align-
ment
Camber
Left-right error-0°30' ± 45'
45' or less
Front axleAxle bearing backlash0.05 mm (0.0020 in.) or lessFront axle
Axle hub deviation0.05 mm (0.0020 in.) or less
Front suspensionLower ball joint turning torque0.8 - 2.5 N´m (8 - 25 kgf´cm, 7 - 22 in.´lbf)
Rear axleBearing preload (turning)Add frictional force plus 0 - 11.8 N (0 - 1.2 kgf, 0 - 2.6 lbf)Rear axle
Axle hub axial play0.05 mm (0.0020 in.) or less

SS0LP-06
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS-33
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT:
Disc brake dust cover x Steering knuckle8.38574 in.´lbf
Lower ball joint x Steering knuckle981,00072
Steering knuckle x Shock absorber2452,500181
Lower ball joint x Lower suspension arm8082059
Tie rod end lock nut4748035
Tie rod end x Steering knuckle4950036
Disc brake caliper x Steering knuckle8890065
Drive shaft lock nut2162,200159
Piston rod x Suspension support4747534
Suspension support x Body3940029
Flexible hose x Shock absorber2930022
Lower suspension arm x BodyFront side1421,450105Lower sus ension arm x Body Front side
Rear side
142
74
1,450
750
105
55
Hub nut1031,05076
ABS speed sensor x Steering knuckle7.88069 in.´lbf
REAR:
Piston rod x Suspension support3435025
Suspension support x Body3940029
Shock absorber x Axle beam6869050
Backing plate x Axle beam7071051
Parking brake cable x Backing plate7.88069 in.´lbf
Brake line x Wheel cylinder1515511
Body x Axle beam1421,450105
Lateral control rod x Axle beam8385061
Lateral control rod x Body11 31,15083
ABS speed sensor x Axle beam7.88069 in.´lbf
ABS speed sensor wire x Axle beam5.45548 in.´lbf

SS0M3-10
- SERVICE SPECIFICATIONSBRAKE
SS-35
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.717.515.2 in.´lbf
Master cylinder x Brake booster131309
Brake line union nut1515511
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket1414510
Front disc brake caliper installation bolt2525518
Bleeding plug8.38574 in.´lbf
Front disc brake torque plate x Steering knuckle8890065
Front disc brake caliper x Flexible hose3031022
Rear drum brake wheel cylinder x Backing plate101007
ABS actuator assembly x Body1919514
ABS actuator x ABS actuator bracket assembly5.45548 in.´lbf
ABS actuator x ABS actuator No. 3 bracket1919514
Front speed sensor x Steering knuckle8.08271 in.´lbf
Front speed sensor wire harness clamp installation bolt5.05144 in.´lbf
Rear speed sensor x Axle beam8.08271 in.´lbf
Rear speed sensor wire harness clamp installation bolt5.05144 in.´lbf

SS0N1-03
SS-36
- SERVICE SPECIFICATIONSSTEERING
166 Author
: Date
:
1996 TERCEL (RM440U)
STEERING
SERVICE DATA
ON-VEHICLE INSPECTION
Steering wheel freeplayMaximum30 mm (1.18 in.)
Drive belt tension New belt140 - 180 lbf Drive belt tension New belt
Used belt
140 180 lbf
80 - 120 lbf
Maximum rise of oil level5 mm (0.20 in.)
Oil pressure at idle speed with valve closed Minimum6,374 kPa (65 kgf/cm2, 925 psi)
Steering effort at idle speedMaximum7.8 N´m (80 kgf´cm, 69 in.lbf)
PS VANE PUMP
Rotor shaft bushing oil clearance STD0.01 - 0.03 mm (0.0004 - 0.0012 in.) Rotor shaft bushing oil clearance STD
Maximum
0.01 0.03 mm (0.0004 0.0012 in.)
0.07 mm (0.0028 in.)
Vane plate heightMinimum8.0 mm (0.315 in.)
Vane plate thickness Minimum1.77 mm (0.0697 in.)
Vane plate lengthMinimum14.97 mm (0.5894 in.)
Vane plate to rotor groove clearanceMaximum0.03 mm (0.0012 in.)
Vane plate length Pump rotor and cam ring mark Vane late length Pum rotor and cam ring mark
None14.996 - 14.998 mm (0.59039 - 0.59047 in.)None
1
14.996 - 14.998 mm (0.59039 - 0.59047 in.)
14.994 - 14.996 mm (0.59032 - 0.59039 in.)1
2
14.994 14.996 mm (0.59032 0.59039 in.)
14.992 - 14.994 mm (0.59024 - 0.59032 in.)2
3
14.992 14.994 mm (0.59024 0.59032 in.)
14.990 - 14.992 mm (0.59016 - 0.59024 in.)3
4
14.990 14.992 mm (0.59016 0.59024 in.)
14.988 - 14.990 mm (0.59008 - 0.59016 in.)
Spring free length36 - 38 mm (1.42 - 1.49 in.)
Vane pump rotating torqueMaximum0.3 N´m (2.8 kgf´cm, 2.4 in.´lbf) or less
MANUAL STEERING GEAR
Steering rack runout Maximum0.30 mm (0.0118 in.)
Pinion preload Turning0.23 - 0.32 N´m (2.3 - 3.3 kgf´cm, 2.0 - 2.9 in.lbf)
Total preload Turning0.6 - 1.2 N´m (6 - 12 kgf´cm, 5.2 - 10.4 in.´lbf)
PS GEAR
Steering rack runout Maximum0.30 mm (0.0118 in.)
Measure oil clearance STD0.050 - 0.083 mm (0.00197 - 0.00327 in.) Measure oil clearance STD
Maximum
0.050 0.083 mm (0.00197 0.00327 in.)
0.125 mm (0.00492 in.)
Total preload Turning0.8 - 1.4 N´m (8 - 14 kgf´cm, 6.9 - 12.2 in.´lbf)

SS0N2-05
- SERVICE SPECIFICATIONSSTEERING
SS-37
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
STEERING COLUMN
Steering support x Column tube5.45548 in.´lbf
Control valve shaft x Sliding yoke2526019
Steering main shaft x Sliding yoke2526019
Steering column assembly set nut2526019
Steering wheel set nut3435025
Steering wheel pad set screw8.89078 in.´lbf
PS VANE PUMP
Pressure port union x Front housing6970051
Suction port union x Front housing131309
Pressure feed tube x Pressure port union5455040
PS vane pump pulley set nut4344032
PS vane pump assembly set nut Bolt A4344032 PS vane um assembly set nut Bolt A
Bolt B
43
39
440
400
32
30
MANUAL STEERING GEAR
Pinion bearing adjusting screw lock nut for use with SST
for use without SST85
11 3871
1,15063
83
Rack guide spring cap lock nut for use with SST
for use without SST41
56419
57530
42
Rack x Rack end for use with SST
for use without SST43
59434
60031
43
Tie rod end lock nut4748035
Manual steering gear bracket x Body5859043
Pinion shaft x Sliding yoke2526019
Steering main shaft x Sliding yoke2526019
Column hole cover x Body4.95043 in.´lbf
PS GEAR
Cylinder end stopper5960043
Self-locking nut5960043
Rack housing cap5960043
Rack guide spring cap lock nut for use with SST
for use without SST31
44316
45023
33
Rack x Rack end for use with SST
for use without SST43
59434
60031
43
Tie rod end lock nut4748035
Turn pressure tube union nut for use with SST
for use without SST20
25203
25015
18
Air control valve2930022
PS gear bracket x Body5859043
Engine rear mount insulator Bolt A6465047 Engine rear mount insulator Bolt A
Bolt B
64
78
650
800
47
58
Engine rear mount bracket x Transaxle4849035
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe clamp1919014
Front exhaust pipe x Oxygen sensor4445032

SS061-41
- SERVICE SPECIFICATIONSSUPPLEMENTAL RESTRAINT SYSTEM
SS-39
169 Author
: Date
:
1996 TERCEL (RM440U)
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Steering wheel3435025
Steering wheel pad8.89078 in.´lbf
Front passenger airbag assembly1919514
Airbag sensor assembly2020014

SS0NJ-06
SS-42
- SERVICE SPECIFICATIONSBODY
172 Author
: Date
:
1996 TERCEL (RM440U)
BODY
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
FRONT SEAT
Seat track x Body3737527
REAR SEAT
Seat back x Body1818513
Seat x Seat center hinge1818513
Seat center hinge x Body7.88069 in.´lbf
Seat x Seat hinge1818513
Seat hinge x Body7.88069 in.´lbf
FRONT SEAT BELT
Shoulder anchor x Adjustable anchor4344032
Outer belt anchor x Body4344032
ELR x Body4344032
Adjustable anchor x Body4344032
Inner belt x Seat4344032
REAR SEAT BELT
Outer belt anchor x Body4344032
ELR x Body4344032
Center belt x Body4344032
CANADA:
CRS, tether anchor x Body
2121015