engine TOYOTA TERCEL 1996 Service Manual PDF

DI-14
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)DTC No.
(See Page)
Detection ItemTrouble AreaMIL*Memory
P0171
(DI-49)System too Lean
(Fuel Trim)
Air intake (hose loose)
Fuel line pressure
Injector blockage
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0172
(DI-49)System too Rich
(Fuel Trim)
Fuel line pressure
Injector blockage, leak
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0300
(DI-52)Random/Multiple Cylinder
Misfire DetectedIgnition system
Injector
FlliP0301
P0302
P0303
P0304
(DI-52)Misfire Detected
- Cylinder 1
- Cylinder 2
- Cylinder 3
- Cylinder 4Fuel line pressure
Compression pressure
Valve clearance not to specification
Valve timing
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0325
(DI-57)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM

P0335
(DI-60)Crankshaft Position Sensor
Circuit ºAº Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM

P0340
(DI-63)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM

P0420
(DI-73)Catalyst System Efficiency
Below ThresholdThree-way catalytic converter
Open or short in (heated) oxygen sensor circuit
(Heated) oxygen sensor

P0500
(DI-76)Vehicle Speed Sensor
Malfunction
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
Speedometer cable
ECM

P0505
(DI-78)Idle Control System
Malfunction
IAC valve is stuck or closed
Open or short in IAC valve circuit
Open or short in AC1 switch circuit
Air intake (hose loose)

*: 


MIL lights up

- DIAGNOSTICSENGINE
DI-15
1996 TERCEL (RM440U)
Manufacturer Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P1300
(DI-84)Igniter Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
Igniter
ECM

P1335
(DI-89)Crankshaft Position Sensor
Circuit Malfunction
(during engine running)Open or short in crankshaft position sensor circuit
Crankshaft position sensor
ECM
-
P1600
(DI-92)ECM BATT MalfunctionOpen in back up power source circuit
ECM
P1780
(DI-94)Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
Park/neutral position switch
ECM

*:-


MIL does not light up



MIL lights up

DI4LG-02
A15676
DI-16
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
PARTS LOCATION

DI4LH-02
P19551
ECM TerminalsE7 E6
1 2 3 4 5 6 7 8 9 10 11 12 13
23 24 25 26 1920 21 22 18 1415 16 171 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
- DIAGNOSTICSENGINE
DI-17
1996 TERCEL (RM440U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E6-2) - E1 (E7-24)W-R - BRAlways9 - 14
+B (E6-9) - E1 (E7-24)B-R - BRIG switch ON9 - 14
VC (E7-18) - E2 (E7-16)LG-R - BRIG switch ON4.5 - 5.5
VTA (E7 19) E2 (E7 16)YG BR
IG switch ON
Throttle valve fully closed0.3 - 1.0
VTA (E7-19) - E2 (E7-16)Y-G - BRIG switch ON
Throttle valve fully open3.2 - 4.9
PIM (E7 4) E2 (E7 16)PBRIG switch ON3.3 - 3.9PIM (E7-4) - E2 (E7-16)P - BRApply vacuum 26.7 kPa (200 mmHg, 7.9 in.Hg)2.5 - 3.1
THA (E7-15) - E2 (E7-16)L-B - BRIdling, Intake air temp. 20°C (68° F)0.5 - 3.4
THW (E7-3) - E2 (E7-16)G-B - BRIdling, Engine coolant temp. 80°C (176°F) 0.2 - 1.0
STA (E7-11) - E1 (E7-24)B-W - BRCranking6.0 or more
IG switch ON9 - 14
#10 (E7-12) - E01 (E7-13)G - BRIdlingPulse generation
(See page DI-52)
IG switch ON9 - 14
#20 (E7-11) - E01 (E7-13)Y - BRIdlingPulse generation
(See page DI-52)
IG switch ON9 - 14
#30 (E7-25) - E01 (E7-13)R - BRIdlingPulse generation
(See page DI-52)
IG switch ON9 - 14
#40 (E7-24) - E01 (E7-13)L - BRIdlingPulse generation
(See page DI-52)
IGT1 (E7-6) - E1 (E7-24)LG - BRIdlingPulse generation
(See page DI-84)
IGT2 (E7-5) - E1 (E7-24)L-Y - BRIdlingPulse generation
(See page DI-84)
IG switch ON, Disconnect igniter connector4.5 - 5.5
IGF (E7-7) - E1 (E7-24)LG-B - BRIdlingPulse generation
(See page DI-84)
G2(E7-20) - NE- (E7-9)R - WIdlingPulse generation
(See page DI-60)
NE(E7-21) - NE- (E7-9)B - WIdlingPulse generation
(See page DI-60)
FC (E6-4) - E1 (E7-24)G-B - BRIG switch ON9 - 14

DI-18
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)Symbols (Terminals No.)
Wiring ColorConditionSTD Voltage (V)
RSC (E7-1) - E1 (E7-24)L-R - BRIG switch ON
Disconnect ºE7º of ECM connector9 - 14
RSO (E7-14) - E1(E7-24)L - BRIG switch ON
Disconnect ºE7º of ECM connector9 - 14
OX1 (E7-10) - E1 (E7-24)B - BRMaintain engine speed at 2,500 rpm for 2 minutes. after
warming upPulse generation
OX2 (E7-23) - E1 (E7-24)W - BRMaintain engine speed at 2,500 rpm for 2 minutes. after
warming upPulse generation
HT1 (E6 6) E03 (E7 26)WL BRIdlingBelow 3.0HT1 (E6-6) - E03 (E7-26)W-L - BRIG switch ON9 - 14
HT2 (E6 5) E03 (E7 26)WR BRIdlingBelow 3.0HT2 (E6-5) - E03 (E7-26)W-R - BRIG switch ON9 - 14
KNK (E7-8) - E1 (E7-24)B - BRIdlingPulse generation
(See page DI-57)
NSW (E7 2) E1 (E7 24)(M/T)
IG switch ON
Other shift position in ºPº or ºNº position9 - 14
NSW (E7-2) - E1 (E7-24)(M/T)IG switch ON
Shift position in ºPº or ºNº position0 - 3.0
NSW (E7 2) E1 (E7 24)(A/T)
IG switch ON
Other shift position in ºPº or ºNº position9 - 14
NSW (E7-2) - E1 (E7-24)(A/T)IG switch ON
Shift position in ºPº or Nº position0 - 3.0
SPD (E6-13) - E1 (E7-24)Y - BRIG switch ON
Rotate driving wheel slowlyPulse generation
(See page DI-76)
TE1 (E6-8) - E1 (E7-24)G - BRIG switch ON9 - 14
W (E6 10) E1 (E7 24)GR L BRIdling9 - 14W (E6-10) - E1 (E7-24)GR-L - BRIG switch ONBelow 3.0
AC1 (E6 12) E1 (E7 24)LG B BRIdling, A/C switch ONBelow 2.0AC1 (E6-12) - E1 (E7-24)LG-B - BRIdling, A/C switch OFF9 - 14
ACT (E6 14) E1 (E7 24)LBRIdling, A/C switch ON9 - 14ACT (E6-14) - E1 (E7-24)L - BRIdling, A/C switch OFFBelow 2.0
ODSW (E6 3) E1 (E7 24)RW BRIG switch ON, O/D main switch pushed out9 - 14ODSW (E6-3) - E1 (E7-24)R-W - BRIG switch ON, O/D main switch pushed in0 - 3.0
ODT (E6 11) E1 (E7 24)RBRIG switch ON, O/D main switch pushed out9 - 14ODT (E6-11) - E1 (E7-24)R - BRIG switch ON, O/D main switch pushed in0 - 3.0

DI4LI-02
- DIAGNOSTICSENGINE
DI-19
1996 TERCEL (RM440U)
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
Does not start (Engine does not crank)1. Starter and starter relayST-13
ST-31
Does not start (No combustion)1. ECM power source circuit
2. Fuel pump control circuitDI-97
DI-100
Does not start (No complete combustion)1. Fuel pump control circuitDI-100
Difficult to start (Engine cranks normally)
1. Starter signal circuit
2. Fuel pump control circuit
3. CompressionDI-90
DI-100
EM-3
Difficult to start (Cold engine)1. Starter signal circuit
2. Fuel pump control circuitDI-90
DI-100
Difficult to start (Hot engine)1. Starter signal circuit
2. Fuel pump control circuitDI-90
DI-100
Poor idling (High engine idle speed)1. A/C signal circuit
2. ECM power source circuitAC-66
DI-97
Poor idling (Low engine idle speed)1. A/C signal circuit
2. Fuel pump control circuitAC-66
DI-100
Poor idling (Rough idling)1. Compression
2. Fuel pump control circuitEM-3
DI-100
Poor idling (Hunting)1. ECM power source circuit
2. Fuel pump control circuitDI-97
DI-100
Poor driveability (Hesitation/Poor acceleration)
1. Fuel pump control circuit
2. A/T faulty (A132L)
A/T faulty (A242L)
3. A/C cut control circuitDI-100
AX-10
AX-13
DI-106
Poor driveability (Surging)1. Fuel pump control circuitDI-100
Engine stall (Soon after starting)1. Fuel pump control circuitDI-100
Engine stall (During A/C operation)1. A/C signal circuit
2. Engine control module (ECM)AC-66
IN-26

DI1E3-06
P01242
750
450
100 (3.96)
3.6
1.2
(840) 2.4
150
60 20
(112)kPa mmHg
Manifold Absolute Pressure
Output Voltage
V DI-20
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
CIRCUIT INSPECTION
DTC P0105 Manifold Absolute Pressure/Barometric
Pressure Circuit Malfunction
CIRCUIT DESCRIPTION
By a built-in sensor unit, the manifold absolute pressure sensor
detects the intake manifold pressure as a voltage. The ECM
then determines the basic injection duration and basic injection
advance angle based on this voltage. Since the manifold abso-
lute pressure sensor does not use the atmospheric pressure as
a criterion, but senses the absolute pressure inside the intake
manifold (the pressure in proportion to the present absolute
vacuum 0), it is not influenced by fluctuations in the atmospheric
pressure due to high altitude and other factors. This permits it
to control the air-fuel ratio at the proper lever under all condi-
tions.
DTC No.DTC Detection ConditionTrouble Area
P0105Open or short manifold absolute pressure sensor circuit

Open or short in manifold absolute pressure sensor circuit

Manifold absolute pressure sensor

ECM
If the ECM detects DTC P0105, it operates the fail-safe function, keeping the ignition timing and injection
volume constant and making it possible to drive the vehicle.
HINT:
After confirming DTC P0105, use the OBDII scan tool or TOYOTA hand-held tester to confirm the manifold
absolute pressure from the CURRENT DATA.
Manifold absolute pressureTrouble Area
0 kPaPIM circuit short
130 kPa or more
VC circuit open or short
PIM circuit open
E2 circuit open

A15677
- DIAGNOSTICSENGINE
DI-21
1996 TERCEL (RM440U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTC P0105, P0110, P0115, P0120 are output simultaneously, E2 (sensor ground) may be open.
1 Connect OBD II scan tool or TOYOTA hand-held tester, and read value of man-
ifold absolute pressure.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand-held tester to the DLC3.
(c) Turn the ignition switch ON and OBDII scan tool or TOYOTA hand-held tester main switch ON.
CHECK:
Read value of manifold absolute pressure on the OBD II scan tool or TOYOTA hand-held tester.
OK:
Same value as the atmospheric pressure
OK Check for intermittent problems (See page
DI-3).
NG

A15678
A15679
DI-22
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
2 Check voltage between terminals VC and E2 of ECM connector.
PREPARATION:
(a) Remove the lower finish panel.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals VC and E2 of the ECM
connector.
OK:
Voltage: 4.5 - 5.5 V
NG Check and replace ECM (See page IN-26).
OK
3 Check voltage between terminals PIM and E2 of ECM connector.
PREPARATION:
(a) Remove the lower finish panel.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals PIM and E2 of ECM con-
nector.
OK:
Voltage: 3.3 - 3.9 V
OK Check and replace ECM (See page IN-26).
NG
4 Check for open and short in harness and connector between manifold absolute
pressure sensor and ECM.
NG Repair or replace harness or connector.
OK
Replace manifold absolute pressure sensor.

- DIAGNOSTICSENGINE
DI-23
1996 TERCEL (RM440U)
DTC P0106 Manifold Absolute Pressure/Barometric
Presure Circuit Range/Performance Problem
CIRCUIT DESCRIPTION
Refer to DTC P0105 on page DI-20.
DTC No.DTC Detection ConditionTrouble Area
P0106
Conditions (a) and (b) continue with engine speed
400 - 1,000 rpm:
(2 trip detection logic)
(a) Closed throttle position switch: ON
(b) Manifold absolute pressure sensor output > 3.0 V

Manifold absolute pressure sensor
WIRING DIAGRAM
Refer to DTC P0105 on page DI-20.
INSPECTION PROCEDURE
HINT:
If DTC P0105 and P0106 are output simultaneously, manifold absolute pressure sensor circuit may be open.
Perform troubleshooting of DTC P0105 first.
1 Are there any other codes (besides DTC P0106) being output?
YES Go to relevant DTC chart.
NO
2 Check manifold absolute pressure sensor (See page MF-48).
NG Replace manifold absolute pressure sensor.
OK
Check vacuum line for manifold absolute
pressure sensor for blockage.
DI1E4-05