light TOYOTA VENZA 2016 Owners Manual

4323-3. Using the interior lights
VENZA_OM_OM73030U_(U) Personal/interior lights
Front
On/off The illuminated entry system is
activated even if the light is
turned off when the personal/inte-
rior light main switch is in door
position.
Rear
On/off The illuminated entry system is
activated even if the light is
turned off when the personal/inte-
rior light main switch is in door
position.
Luggage compartment light
Off
Door positionPersonal/interior lights and luggage compartment light

4333-3. Using the interior lights
3
Interior features
VENZA_OM_OM73030U_(U) ■ To prevent the battery from being discharged
Vehicles with smart key system
If the personal/interior lights and “ENGINE START STOP” switch light
remain on when the door is not fully closed and the personal/interior light
main switch is in door position, the lights will go off automatically after 20
minutes.
Vehicles without smart key system
If the personal/interior lights and engine switch light remain on when the
door is not fully closed and the personal/interior light main switch is in
door position, the lights will go off automatically after 20 minutes.
■ Customization
Settings (e.g. The time elapsed before lights turn off) can be changed.
(Customizable features
 P. 645)

4353-4. Using the storage features
3
Interior features
VENZA_OM_OM73030U_(U) Glove box
Pull up the lever.CAUTION■ Items that should not be left in the storage spaces
Do not leave glasses, lighters or spray cans in the storage spaces, as this
may cause the following when cabin temperature becomes high:
● Glasses may be deformed by heat or cracked if they come into contact
with other stored items.
● Lighters or spray cans may explode. If they come into contact with other
stored items, the lighter may catch fire or the spray can may release gas,
causing a fire hazard.
■ Glove box light
The glove box light turns on when the tail lights are on.
CAUTION■ While driving
Keep the glove box closed. In the event of sudden braking or sudden swerv-
ing, an accident may occur due to an occupant being struck by the open
glove box or the items stored inside. Glove box

4463-5. Other interior features
VENZA_OM_OM73030U_(U)Vanity mirror Slide the cover. The light turns on when the
cover is opened.

4493-5. Other interior features
3
Interior features
VENZA_OM_OM73030U_(U) Seat heaters 
 : If equipped■ The seat heaters can be used when
Vehicles with smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
Vehicles without smart key system
The engine switch is in the “ON” position. For driver’s seat
For front passenger’s seat
On The indicator light comes on.
Adjusts the seat tempera-
ture The further you turn the dial
upward, the warmer the seat
becomes.

4573-5. Other interior features
3
Interior features
VENZA_OM_OM73030U_(U) Garage door opener The garage door opener (HomeLink 
Universal Transceiver) is manufac-
tured under license from HomeLink 
.
Programming HomeLink ®
(for U.S.A. owners)To ensure correct programming into the HomeLink ®
, install a new bat-
tery in the hand-held transmitter prior to programming. Failure to
install a new battery into the hand-h eld transmitter will affect both the
range and accuracy of the HomeLink ®
in your vehicle.
The battery side of the hand-held transmitter must be pointed away
from the HomeLink ®
during the programming process.
The HomeLink 
compatible transceiver in your vehicle has 3 buttons
which can be programmed to operate 3 different devices. Refer to the
programming method below appropriate for the device.
Indicator
ButtonsThe garage door opener can be programmed to operate garage
doors, gates, entry do ors, door locks, home lighting systems, secu-
rity systems, and other devices.

4583-5. Other interior features
VENZA_OM_OM73030U_(U) ■ Programming HomeLink ®
Point the remote control trans-
mitter for the device 1 to 3 in. (25
to 75 mm) from the HomeLink 
buttons. Keep the HomeLink 
indicator
light in view while programming.
Press and hold one of the
HomeLink 
buttons and the
transmitter button. When the
HomeLink 
indicator light
changes from a slow to a rapid
flash within 20 seconds, you can
release both buttons.STEP 1
STEP 2

4593-5. Other interior features
3
Interior features
VENZA_OM_OM73030U_(U) Test the HomeLink 
operation
by pressing the newly pro-
grammed button. If a HomeLink 
button has been
programmed for a garage door,
check to see if the garage door
opens and closes. If the garage
door does not operate, see if your
remote control transmitter is of
the rolling code type. Press and
hold the programmed HomeLink 
button. The remote control trans-
mitter is of the rolling code type if
the HomeLink 
indicator light
flashes rapidly for 2 seconds and
then remains lit. If your transmit-
ter is of the rolling code type, pro-
ceed to the heading
“Programming a rolling code sys-
tem”.
Repeat the steps above to program another device for each of
the remaining HomeLink 
buttons.STEP 3
STEP 4

4613-5. Other interior features
3
Interior features
VENZA_OM_OM73030U_(U) ■ Programming an entry gate (f or U.S.A. owners)/Programming
all devices in the Canadian market
Place your transmitter 1 to 3 in. (25 to 75 mm) away from the
surface of the HomeLink 
.Keep the HomeLink 
indicator light in view while programming.
Press and hold the selected HomeLink 
button.
Repeatedly press and releas e (cycle) the device’s remote
control button for two seconds each until step 4 is completed.
When the indicator light on the HomeLink 
compatible trans-
ceiver starts to flash rapidly, release the buttons.
Test the operation of the HomeLink 
by pressing the newly
programmed button. Check to see if the gate/device operates
correctly.
Repeat the steps above to program another device for each of
the remaining HomeLink 
buttons.
■ Programming other devices
To program other devices such as home security systems, home
door locks or lighting, contact your authorized Toyota dealer for
assistance.
■ Reprogramming a button
The individual HomeLink 
buttons cannot be erased but can be
reprogrammed. To reprogram a bu tton, follow the “Programming”
instructions. STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6

4623-5. Other interior features
VENZA_OM_OM73030U_(U) Operating HomeLink ®
Press the appropriate HomeLink 
button. The HomeLink 
indicator
light should come on. The HomeLink 
compatible transceiver in your vehicle continues to send
a signal for up to 20 seconds as long as the button is pressed.
Erasing the entire HomeLink ®
memory (all three programs)
Press and hold the 2 outside but-
tons for 10 seconds (or 20 sec-
onds depending on the model)
until the indicator light flashes. If you sell your vehicle, be sure to
erase the programs stored in the
HomeLink 
memory.