reset TOYOTA xD 2010 Accessories, Audio & Navigation (in English)

15
ALPINE MFTY802A 68-14470Z28-C (EN)
3 Selecting TUNE (Dial 2)/Setting
the Preset List mode (
/Dial
2)/Setting Multicast List mode
(
/Dial 2)
In normal mode, turn the Dial 2 to se-
lect the desired radio station.
Listening to the RADIO
NOTICE
Attaching any film or window tint
film (especially conductive or me-
tallic type) on the rear glass will
noticeably reduce the sensitivity of
the radio.
This does not apply to cars with
pole antennas as window film does
not reduce the antenna’ s recep-
tion.
1 FM 1/2
Activates the radio mode. Switches
between FM 1 and FM 2 band.
2AM/SAT
Switches between the AM mode and
SAT1/2/3 modes. (must have Satellite
Radio receiver and antenna installed
at an additional charge to listen to
Satellite Radio.)

16
ALPINE MFTY802A 68-14470Z28-C (EN)
Presetting Stations
1 Select the radio band and tune in a
desired radio station you wish to
store in the preset memory, and
then press
to recall the Pre-
set List mode
2T urn the Dial 2 within 10 seconds
to select the desired preset num-
ber. The selected preset number is
displayed with frame.
3Pr ess and hold
for at least 2
seconds. The selected station is stored.
4Pr ess
in the Preset List mode to
r eturn to normal mode.
Return
Page down
Page up
Preset 1-4(altogether
there are 6 “presets”)Preset List mode
5
Repeat the procedure to store up
to 5 other stations onto the same
band. To use this procedure for other
bands, simply select the desired
band and repeat the procedure. A total of 18 stations can be stored
in the preset memory (6 stations for
each band; FM1, FM2 or AM).
NOTICE
Y ou can also preset a radio station
in Preset mode. Refer to “Soft but-
ton operation” on page 18.
Select frame *
*The selected preset number is dis-
played with this frame. (In Preset List mode, touch and hold a
preset number until it beeps, the cur-
r ent station will be stored to it.)

17
ALPINE MFTY802A 68-14470Z28-C (EN)
T uning to Preset Stations
1 After selecting the desired band,
press
to recall Preset List
mode.
2T urn the Dial 2 within 10 seconds
to select the desired preset num-
ber.
3Pr ess
.
The preset station is received.
Return
Page down
Page up
Preset 1-4(altogether
there are 6 “presets”)
Preset List mode
*
The selected preset number is dis-
played with this frame. (In Preset List mode, touch a preset
number will receive it)
NOTICE
Y ou can also recall a preset sta-
tion in Preset mode. Refer to “Soft
button operation” on page 18.
Select frame *
Multicast mode
When multicast station is received, the
[CHANNEL LIST] soft button appears.
1T ouch [CHANNEL LIST] to activate
Multicast List mode
2T urn the Dial 2 to select the desired
program service.
3Pr ess
to receive the se-
lected program.

19
ALPINE MFTY802A 68-14470Z28-C (EN)
Preset mode
Preset 1-3 Preset 4-6
4
Preset mode ON/OFF2Touch [SCAN] to cancel the scan-
ning when the desired program is
found.
• During scan search, touching
[SCAN] will cancel TUNE SCAN
and activate TUNE SEEK UP.
• During scan search, selecting a
program by turning the Dial 2 will
cancel TUNE SCAN.
• Operate TUNE SEEK UP/DOWN,
r ecalling preset program will can-
cel TUNE SCAN.
PRESET SCAN
1T ouch and hold [SCAN] for at least
2 seconds to scan the preset radio
stations. The P.SCAN indicator
lights up, and the first 5 seconds of
each scanned preset radio station
is played.
2T ouch [SCAN] to cancel the scan-
ning when the desired preset sta-
tion is found.
• Operate TUNE SEEK UP/DOWN,
r ecalling preset program will can-
cel PRESET SCAN.
• During scan search, selecting a
program by turning the Dial 2 will
cancel TUNE SCAN.
Touch
[P.SET] to activate or deacti-
vate Preset mode.
In Preset mode, touch any one of the
Preset buttons to recall a stored sta-
tion.
In Preset mode, touch and hold the
button until it beeps while a station is
being received to store that station to
the preset number you touched.
5 TUNE SCAN/PRESET SCAN
TUNE SCAN
1Touch [SCAN] to scan the radio sta-
tions. The first 5 seconds of each
scanned radio station is played.

27
ALPINE MFTY802A 68-14470Z28-C (EN)
NOTICE
To resolve most problems when us-
ing your iPod with the Scion Audio
system, disconnect your iPod from
the vehicle iPod connection and re-
set it.
For instructions on how to reset your
iPod, refer to your iPod Owner ’s
Manual.NOTICE
• Do not use the car’s cigarette lighter adapter to power your iPod.Noise may result.
• Push in until you hear a click to con- nect firmly. If it does not go in
smoothly, it may be upside down so
do not force it in as this may result
in damage.
• Connect the Dock connector di-
rectly to the Dock connector port.Disconnecting the iPod
Remove the iPod from this unit.
When removing the iPod from this unit,
the iPod main menu appears in the
iPod display after a few seconds.
During iPod mode, removing the iPod
from the unit will change the source to
the last one selected.
When disconnecting, hold part of the
connector and press the lock while
pulling. Pulling out by the cord may pull
the cord out of the connector.

34
ALPINE MFTY802A 68-14470Z28-C (EN)
Listening to a Satellite
Radio broadcast
1 AM/SAT
Switches between the AM mode and
SAT1/2/3 modes. (must have Satellite
Radio receiver and antenna installed
at an additional charge to listen to
Satellite Radio.)
2TUNE UP/DOWN (Dial 2)/Setting
Preset List mode (
/Dial 2)
In the normal mode, turn the Dial 2 to
select the desired radio station.
Presetting Stations
1 Select the radio band and tune in a
desired radio station you wish to
store in the preset memory, and
then press
to recall the Pre-
set List mode 2T
urn the Dial 2 within 10 seconds
to select the stored Preset number.
3Pr ess and hold
for at least 2
seconds.
The selected station is stored.
4 Repeat the procedure to store up
to 5 other stations onto the same
band.
To use this procedure for other
bands, simply select the desired
band and repeat the procedure.
A total of 18 stations can be stored
in the preset memory (6 stations for
each band; SAT1/2/3).
Preset list modeReturn
Page down
Page up
Preset 1-4(altogether
there are 6 “presets”)

35
ALPINE MFTY802A 68-14470Z28-C (EN)
Channel number
Channel name Song nameArtist name
T uning to Preset Stations
1 After selecting the desired band,
press
to recall the Preset List
mode.
2T urn the Dial 2 within 10 seconds
to select the stored preset number.
3Pr ess
.
The preset station is received.
Soft button operation
3 TUNE
Touch to manually select the desired
channel. Each touch advances to the
next channel of the category. (one
step at a time)
4 TUNE
Touch to manually select the desired
channel. Each touch returns to the
previous channel of the category. (one
step at a time)
5 Category UP
After touching this button initially, the
currently received category name will
be displayed and then the name will
be changed to the category selection
mode.
If the button is touched during the cat-
egory mode, the category moves up
to the next, then the category name
is displayed.
6Category DOWN
After touching this button initially, the
currently received category name will
be displayed, and then the name will
be changed to the category selection
mode.
If the button is touched during the cat-
egory mode, the category moves
down to the next, then the category
name is displayed.

36
ALPINE MFTY802A 68-14470Z28-C (EN)
7 SCAN
Touch and SCAN of the currently se-
lected type (Channel Category)
starts. The first 5 seconds of each
scanned station is played. At this time,
SCAN is indicated in the display.
T ouch again to cancel.
When this button is touched and held
until it beeps, SCAN of preset chan-
nels starts. The first 5 seconds of each
scanned preset station is played. At
this time, P.SCAN is indicated in the
display. Touch again to cancel.
8 Preset mode ON/OFF
Touch [P.SET] to activate or deacti-
vate Preset mode. In Preset mode, touch any one of the
preset buttons to recall a stored sta-
tion.
In Preset mode, touch and hold the
button until it beeps while a station is
being received to store that station to
the preset number you touched.
Preset mode
Preset 1-3
Preset 4-6

43
ALPINE MFTY802A 68-14470Z28-C (EN)
Using the Steering
Controller
In vehicles equipped with the steering
control, you can use the controller to
operate this product.
Operation button names and func-
tions
L Volume buttons (–
+)
Press to raise the volume level.
Press
to lower the volume level.
L Mode selection button (MODE)
•
When power to this product is OFF:
Press the button and power
switches ON.
• When power to this product is ON: Each time you press the button the
*source changes. If you continue
pressing the button for an extended
period, power to this product
switches OFF.
* The source switches in the follow-
ing order:
FM1 → FM2 → DISC → (iPod/USB)
→ (AUX/VIDEO) → (AUX/Mini Jack)
→ (SAT1/SAT2/SAT3) → AM
NOTICE
• If an iPod, USB, VTR, Mini Jack or
SAT is not connected, its mode will
be skipped.
• When no disc is loaded, the DISC
(CD/MP3/WMA/AAC) mode will be
skipped.
L Track/station selection button
(
)
• When listening to the radio: Press the button to recall the pre-
set memory in order.
Press and hold the button until it
beeps will activate TUNE SEEK
UP/DOWN function.
Press and hold the button will
change the tune continuously.
• When listening to a CD: Press the button to select a track.
• When listening to MP3/WMA/AAC: Press the button to select a file in
folder.
Press and hold the button to se-
lect a folder. • When listening to the iPod:
Press the button to select a track
in album.
•
When listening to a SAT broadcast:
Press the button to recall preset
channels in order.