key TOYOTA YARIS 2016 Owner's Guide

YARIS_SEDAN_OM_OM99M18z_(U)
1433-1. Start/Stop Engine
3
When Driving
After starting the engine, let it idle for about ten seconds.
●The key must be carried because the key carries an immobilizer chip that
must communicate with the engine controls at short range.
● The engine can be started when the push button start is pressed from off,
ACC, or ON.
● The push button start system functions (function which can start the engine
by only carrying the key) can be deactivated to prevent any possible
adverse effect on a user wearing a pacemaker or other medical device. If
the system is deactivated, you will be unable to start the engine by carrying
the key. Consult your Toyota dealer for details. If the push button start sys-
tem functions have been deactivated, you can start the engine by following
the procedure indicated when the key battery goes dead.
Refer to Engine Start Function When Key Battery is Dead on P. 145.
● After starting a cold engine, the engine speed increases and a whining
sound from the engine compartment can be heard.
This is for improved exhaust gas purification and does not indicate defect of
the parts.
● Engine-starting is controlled by the spark ignition system.
This system meets all Canadian Interference-Causing Equipment Standard
requirements regulating the impulse elec trical field strength of radio noise.
● Under the following conditions, the KEY warning light (red) flashes after the
push button start is pressed to inform the driver that the push button start
will not switch to ACC even if it is pressed from off.
• The key battery is dead.
• The key is out of operational range.
• The key is placed in areas where it is difficult for the system to detect the signal ( →P. 93).
• A key from another manufacturer similar to the key is in the operational
range.
8
YARIS_SEDAN_OM_OM99M18z_(U).book Page 143 Monday, June 1, 2015 9:22 PM

144
YARIS_SEDAN_OM_OM99M18z_(U)
3-1. Start/Stop Engine
●Forced engine starting method:
If the KEY warning light (red) illuminates, or the push button start indicator
light (amber) flashes, this could indicate that the engine may not start using
the usual starting method. Have your vehicle inspected at your Toyota
dealer as soon as possible. If this occurs, the engine can be force-started.
Press and hold the push button start unt il the engine starts. Other proce-
dures necessary for starting the engine such as having the key in the cabin,
and depressing the clutch pedal (manual transaxle) or the brake pedal
(automatic transaxle) are required.
● When the engine is force-started, the KEY warning light (red) remains illumi-
nated and the push button start indicator light (amber) remains flashing.
● Automatic transaxle:
When the selector lever is in the neutral (N) position, the KEY indicator light
(green) and the push button start indicator light (green) do not illuminate.
● After pressing the push button start and before the engine starts, the opera-
tion sound of the fuel pump motor from near the fuel tank can be heard,
however, this does not indicate a malfunction.
● Whether the engine is cold or warm, it should be started without the use of
the accelerator.
● If the engine does not start the first ti me, refer to Starting a Flooded Engine
under Emergency Starting. If the engine still does not start, have your vehi-
cle inspected by your Toyota dealer ( →P. 500).
WARNING
■Radio waves from the key may affect medical devices such as pace-
makers
Before using the key near people who use medical devices, ask the medical
device manufacturer or your physician if radio waves from the key will affect
the device.
NOTICE
If the KEY warning light (red) illuminates, or the push button start indicator
light (amber) flashes, this could indi cate a problem with the engine starting
system and the inability to start the engine or switch the ignition to ACC or
ON. Have your vehicle inspected at your Toyota dealer as soon as possible.
YARIS_SEDAN_OM_OM99M18z_(U).book Page 144 Monday, June 1, 2015 9:22 PM

YARIS_SEDAN_OM_OM99M18z_(U)
1453-1. Start/Stop Engine
3
When Driving
If the engine cannot be started due to a dead key battery, the engine
can be started using the following procedure:Continue to depress the brake pedal firmly until the engine has
completely started.
Manual transaxle:
Continue to depress the clutch pedal firmly until the engine has
completely started.
Verify that the push button start indication light (green) flashes.
The push button start indicator light (green) will flash even if the push but-
ton start is pressed before depressing the clutch pedal (manual transaxle)
or the brake pedal (automatic transax le). If the clutch pedal is depressed
(manual transaxle) or the brake pedal is depressed (automatic transaxle)
under this condition, the engine can be started by resuming the procedure
following this.
Touch the push button start
using the backside of the key
(as shown) while the push but-
ton start indicator light (green)
flashes.
When touching the push button
start using the backside of the key
as shown in the illustration, touch
the push button start with the lock
switch side of the key facing up.
Verify that the push button start indicator light (green) turns on.
Press the push button start to start the engine.
● The engine cannot be started unless the clutch pedal is fully depressed
(manual transaxle) or the brake pedal is fully depressed (automatic
transaxle).
● If there is a malfunction with the push button start function, the push button
start indicator light (amber) flashes. In this case, the engine may start, how-
ever, have the vehicle checked at your Toyota dealer as soon as possible.
● If the push button start indicator light (green) does not illuminate, perform
the operation from the beginning again. If it does not illuminate, have the
vehicle checked at your Toyota dealer.
● To switch the ignition position without starting the engine, perform the follow-
ing operations after the push button start indicator light (green) turns on.
Release the clutch pedal (manual transaxle) or brake pedal (automatic
transaxle).
Engine Start Function When Key Battery is Dead
1
2
3
Smart Key
Indicator light
Push button start
4
5
6
1
YARIS_SEDAN_OM_OM99M18z_(U).book Page 145 Monday, June 1, 2015 9:22 PM

146
YARIS_SEDAN_OM_OM99M18z_(U)
3-1. Start/Stop Engine
Press the push button start to switch the ignition position. The ignition
switches in the order of ACC, ON, and off each time the push button start
is pressed. To switch the ignition position again, perform the operation
from the beginning.
If the KEY warning light (red) illuminates, or the push button start indi-
cator light (amber) flashes, this could indicate that the engine may not
start using the usual starting method. Have your vehicle inspected at
your Toyota dealer as soon as possible. If this occurs, the engine can
be force-started. Press and hold the push button start until the engine
starts. Other procedures necessary for starting the engine such as
having the key in the cabin, and depressing the clutch pedal (manual
transaxle) or the brake pedal (automatic transaxle) are required.
NOTICE
When starting the engine by holding the smart key over the push button
start due to a dead key battery or a malfunctioning key, be careful not to
allow the following, otherwise the signal from the key will not be received
correctly and the engine may not start.
● Devices for electronic purchases, or security passage touch or come near
the key.
Emergency Operation for Starting the Engine
2
●Metal parts of other keys or metal
objects touch the key.
● Spare keys or keys for other vehicles
equipped with an immobilizer system
touch or come near the key.
YARIS_SEDAN_OM_OM99M18z_(U).book Page 146 Monday, June 1, 2015 9:22 PM

147
YARIS_SEDAN_OM_OM99M18z_(U)
3-1. Start/Stop Engine
3
When Driving
Tur ning the Engine Off
Stop the vehicle completely.
Manual transaxle:
Shift into neutral and set the parking brake.
Automatic transaxle:
Shift the selector lever to the P position and set the parking brake.
Press the push button start to turn off the engine. The ignition posi-
tion is off.
●The cooling fan in the engine compartment could turn on for a few minutes
after the ignition is switched from ON to OFF, whether or not the A/C is on or
off, to cool the engine compartment quickly.
● When the push button start is pressed from ON to ACC or OFF, the KEY
indicator light (green) may flash for approximately 30 seconds indicating
that the remaining battery power of the key is low.
Replace with a new battery before the key becomes unusable.
Refer to Key Battery Replacement on P. 443.
● Automatic transaxle:
If the engine is turned off while the selector lever is in a position other than
P, the ignition switches to ACC.
Continuously pressing the push button start or quickly pressing it two
or more times while the engine is running or the vehicle is being
driven will turn the engine off immediately. The ignition switches to
ACC.
WARNING
■Do not stop the engine while the vehicle is moving
Stopping the engine while the vehicle is moving for any reason other than in
an emergency is dangerous. Stopping the engine while the vehicle is mov-
ing will result in reduced braking ability due to the loss of power braking,
which could cause an accident and serious injury.
NOTICE
When leaving the vehicle, make sure the push button start is off.
Emergency Engine Stop
1
2
3
YARIS_SEDAN_OM_OM99M18z_(U).book Page 147 Monday, June 1, 2015 9:22 PM

YARIS_SEDAN_OM_OM99M18z_(U)
1573-2. Combination Meter and Display
3
When Driving
These lights turn on or flash to notify the user of the system operation
status or a system malfunction.
*1: The light turns on when the ignition is switched on for an operation check,and turns off a few seconds later or when the engine is started. If the light
does not turn on or remains turned on, have the vehicle inspected at your
Toyota dealer.
*2: The light turns on continuously when the parking brake is applied.
Warning Lights
*1Master Warning Light
(→ P. 507)*1Air Bag/Front Seat Belt
Pretensioner System
Warning Light ( →P. 507)
*1, 2Brake System Warning
Light ( →P. 507) Low Fuel Warning Light
(
→ P. 507)
*1ABS Warning
Light ( →P. 507)*1Check Fuel Cap
Warning Light ( →P. 507)
*1Charging System
Warning Light ( →P. 507) Seat Belt Warning Light
(Front seat) (
→P. 507)
*1Engine Oil Warning
Light ( →P. 507) Door-Ajar Warning Light
(
→ P. 507)
*1Check Engine Light
(→ P. 507)
(If equipped)
Low Washer Fluid Level
Warning Light ( →P. 507)
*1
(Red)
High Engine Coolant
Temperature Warning
Light ( →P. 507)*1
(If equipped)
Tire Pressure Monitoring
System Warning Light
(→ P. 507)
*1
(If equipped)
Automatic Transaxle
Warning Light ( →P. 507)*1
(Red)
KEY Warning Light
(→ P. 507)
*1Power Steering
Malfunction Indicator
Light ( →P. 507)
(Amber)
(If equipped)
Smart City Brake
Support (SCBS)
Warning Light ( →P. 507)
YARIS_SEDAN_OM_OM99M18z_(U).book Page 157 Monday, June 1, 2015 9:22 PM

158
YARIS_SEDAN_OM_OM99M18z_(U)
3-2. Combination Meter and Display
These lights turn on or flash to notify the user of the system operation
status or a system malfunction.
*1: The light turns on when the ignition is switched on for an operation check,and turns off a few seconds later or when the engine is started. If the light
does not turn on or remains turned on, have the vehicle inspected at your
Toyota dealer.
Indicator Lights
(Green)
KEY Indicator Light
(→ P. 142) Headlight High-Beam
Indicator Light
(
→ P. 176, 176)
*1
(If equipped)
Wrench Indicator Light
(→ P. 159) Turn Signal/Hazard
Warning Indicator Lights
(
→ P. 180, 186)
*1TCS/DSC Indicator
Light ( →P. 195, 197)*1Security Indicator Light
(→ P. 122)
*1DSC OFF Indicator Light
(→ P. 197)
(Amber)
(If equipped)
Cruise Main Indicator
Light ( →P. 214)
*1
(Red)
(If equipped)
Smart City Brake
Support (SCBS)
Indicator Light ( →P. 209)
(Green)
(If equipped)
Cruise Set Indicator
Light ( →P. 214)
*1
(If equipped)
Smart City Brake
Support (SCBS) OFF
Indicator Light ( →P. 210)
(If equipped)
Select Mode Indicator
Light ( →P. 202)
(Blue)
Low Engine Coolant
Temperature Indicator
Light ( →P. 159) Lights-On Indicator Light
(
→ P. 175)
(If equipped)
Shift Position Indication
(→ P. 165)*1Front Passenger
Air Bag Deactiva-
tion Indicator
Light ( →P. 78)
sec_03-02.fm Page 158 Wednesday, June 3, 2015 1:43 PM

YARIS_SEDAN_OM_OM99M18z_(U)
1773-4. Switches and Controls
3
When Driving
The coming home light system turns on the headlights (low beams)
when the lever is operated.
■To turn on the system
When the lever is pulled with
the ignition switched to ACC or
OFF, the low beam headlights
turn on.
The headlights turn off after a
certain period of time has
elapsed after the doors are
closed.
●The time until the headlights turn off after all of the doors are closed can be
changed.
Refer to Customizable Features on P. 572.
● If no operations are done for 3 minutes after the lever is pulled, the head-
lights turn off.
● The headlights turn off if the lever is pulled again while the headlights are
illuminated.
The leaving home light system turns on the lights when the smart key
unlock button is pressed while away from the vehicle.
Lock button
Unlock button
Coming Home Light System
Leaving Home Light System
1
2
YARIS_SEDAN_OM_OM99M18z_(U).book Page 177 Monday, June 1, 2015 9:22 PM

178
YARIS_SEDAN_OM_OM99M18z_(U)
3-4. Switches and Controls
■To turn on the system
When the ignition switch and the headlight switch are as indicated
below, the headlights will illuminate when the smart key unlock but-
ton is pressed and the vehicle receives the smart key signal. The
headlights turn off after a certain period of time has elapsed (30
seconds).• Ignition switch: off
• Headlight switch: or
The following lights turn on when the leaving home light system is
operated.
Low beams, Parking lights, Taillights, License lights
● Operation of the leaving home light system can be turned on or off.
Refer to Customizable Features on P. 572.
● When the smart key lock button is pressed and the vehicle receives the
smart key signal, the headlights turn off.
● When the headlight switch is in a position other than or , the head-
lights turn off.
Some countries require moving vehicles to have their lights on (day-
time running lights) during the daytime.
The daytime running lights turn on automatically when the vehicle
starts moving.
They turn off when the parking brake is operated or the shift lever is
shifted to the P position (automatic transaxle vehicle).
Except Canada:
The daytime running lights can be deactivated.
Refer to Customizable Features on P. 572.
Daytime Running Lights
YARIS_SEDAN_OM_OM99M18z_(U).book Page 178 Monday, June 1, 2015 9:22 PM

YARIS_SEDAN_OM_OM99M18z_(U)
3734-3. Bluetooth®
4
Interior Features
●Deleting from your favorites
Select the icon on the home screen and display the
Communication screen.
Select to display the favorites list.
Select .
Select .
Select the contact information which you would like to delete.
Select .
● Changing the display order of your favorites list
Select the icon on the home screen and display the
Communication screen.
Select to display the favorites list.
Select .
Select .
The contact can be moved after it is selected.
Slide the contact or move it using the commander switch, then
select .
● Changing contact name of your favorites
Select the icon on the home screen and display the
Communication screen.
Select to display the favorites list.
Select .
Select .
Select the contact to display the keyboard screen.
If a new name is input and is selected, the contact name is
stored.
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
YARIS_SEDAN_OM_OM99M18z_(U).book Page 373 Monday, June 1, 2015 9:22 PM