turn signal bulb VAUXHALL CORSA 2014.5 Owner's Manual

80Instruments and controlsTurn signal
O illuminates or flashes green.
Illuminates The control indicator illuminates
briefly when the parking lights are
switched on 3 102.
Flashes
The control indicator flashes if a turn
signal or the hazard warning flashers
are activated.
Rapid flashing: failure of a turn signal light or associated fuse, failure of turn
signal light on trailer.
Bulb replacement 3 153, Fuses
3 166, Turn signals 3 101.
Seat belt reminder
X illuminates or flashes red.
Illuminates
After the ignition is switched on until
the seat belt is fastened.Flashes
After starting off until the seat belt is
fastened.
Fastening the seat belt 3 39.
Airbag and belt tensioners
v illuminates red.
When the ignition is switched on, the
control indicator illuminates for
approx. 4 seconds. If it does not
illuminate, does not go out after
4 seconds or illuminates whilst
driving, there is a fault in the belt
tensioner or the airbags. In this case
the LEDs in the button W will also
flash. The airbags and belt tensioners
may fail to trigger in the event of an
accident.
Deployment of the belt tensioners or
airbags is indicated by continuous
illumination of v.9 Warning
Have the cause of the fault
remedied immediately by a
workshop.
Airbag system, belt tensioners 3 41,
3 38.
Airbag deactivation W illuminates together with the LEDs
in the button W: airbag deactivated
3 46.
W flashes: the system can be
activated or deactivated within
15 seconds of switching on the
ignition 3 46.
Charging system
p illuminates or flashes red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.

156Vehicle care
2. Remove bulb from socket, insertnew bulb.
3. Insert bulb holder in reflector so that the locating tab of the bulb
holder aligns with the reflector
recess.
4. Rotate clockwise to engage.
Front turn signal light
Front turn signal lights are equipped
with longlife bulbs. In case of failure,
have bulb replaced by a workshop.
Adaptive forward lighting
Headlights have separate systems for low and high beam 1 (outer bulb),
cornering light 2 (inner bulb) and
daytime running light/side light 3.
Low/high beam
1. Disengage wire clip and remove
protective cover 1.

158Vehicle care
Cornering light
1. Rotate protective cover 2
anticlockwise and remove.
2. Detach wiring plug from bulb.
3. Disengage spring clip from retainer by moving and swivelling
to the side.
4. Remove bulb from reflector housing.
5. When installing the new bulb, insert lugs in the reflectorrecesses.
6. Install spring clip, plug connector onto bulb.
7. Install protective cover.
Front turn signal light
1. Disengage wire clip and remove protective cover 1.

Vehicle care161
5. Gently press the three lockinglugs on the outside of the bulb
holder outwards and remove bulb
holder.
6. Push bulb into socket slightly, rotate anti-clockwise, remove and
renew bulb.
Rear fog light, may be only on one side ( 1)
Reverse light ( 2)
Turn signal light ( 3)
Tail light/side light ( 4)
Tail light/brake light ( 5)
7. Engage bulb holder in bulb
housing, ensuring that it properly
engages.
8. Ensure that the bulb holder seal is
positioned as illustrated.
9. Insert bulb housing in vehicle body, tighten securing nuts by
hand. Engage plug connector.
Close cover.
After bulb replacement, check the tail lights for proper functionality: switch
on the ignition, operate the brake,
switch on the sidelights.

Vehicle care163
5. Gently press the three lockinglugs on the outside of the bulb
holder outwards and remove bulb
holder.
6. Push bulb into socket slightly, rotate anti-clockwise, remove and
renew bulb.
Reverse light (right side), rear fog
light (left side) ( 1)
Tail light ( 2)
Turn signal light ( 3)
Tail light/brake light ( 4)
Tail light ( 5)
7. Engage bulb holder in bulb
housing, ensuring that it properly
engages.
8. Ensure that the bulb holder seal is
positioned as illustrated. Fit the
round seal on the fastening bolt.
9. Insert bulb housing in vehicle body, and tighten securing nuts byhand. Engage plug connector.
Close and lock cover.
After bulb replacement, check the tail
lights for proper functionality: switch
on the ignition, operate the brake,
switch on the sidelights.
Side turn signal lights
To replace bulb, remove lamp
housing:
1. On left vehicle side, slide lamp to the front and remove it out of the
front wing with the rear end.
On right vehicle side, slide lamp to
the rear and remove it out of the front wing with the front end.