ignition VOLKSWAGEN BEETLE CONVERTIBLE 2013 3.G User Guide

Messages in the instrument cluster display
When the ignition is switched on, the indicator lights come on briefly for a function check. They go out
after a few seconds.

Display text Proper response
Speed too high!
Reduce your speed. You can only operate the convertible top at speeds
up to about 30 mph (50 km/h) . If the convertible top has already begun
opening or closing, it will stop if you drive faster. You can only continue
opening or closing the convertible top once the vehicle speed drops
below about 30 mph (50 km/h).
Decrease speed!
Reduce your speed. At 28 mph (45 km/h), the system warns the driver
not to exceed the maximum speed for opening or closing. If the opening
or closing process has already started, it will not stop.
Convert. top:
Release cover!
Convertible top cover (boot) is still installed. Roof operation is not possi-
ble. Remove the convertible top cover.
Error:
Convertible top
Service!
See an authorized Volkswagen dealer or authorized Volkswagen Service
Facility. You cannot operate the convertible top if a system component
malfunctions. Use the emergency procedure to close the open converti-
ble top if necessary
Error:
Open convertible
top!
Open the convertible top
Error:
Close convertible
top!
Have the system checked by an authorized Volkswagen dealer or an
authorized Volkswagen Service Facility. There is a malfunction in a
control module. It is not possible to open or close the convertible top.
Use the emergency procedure to close the convertible top .
Low voltage:
Please start en-
gine!
The vehicle battery is drained to the point that it cannot provide the
power needed to completely open or close the convertible top. Start the
engine by jump-starting if necessary. Open or close the convertible top
while the engine is running. Volkswagen recommends taking a longer
drive afterward to help recharge the vehicle battery.
Convertible
top open
This message and a chime confirm that the convertible top is completely
open or closed.
Convertible
top closed
Convertible top
not functional.
Owner's manual!
Outside temperature too low. You can still close the convertible top, if
necessary.
Have the system checked by an authorized Volkswagen dealer or an
authorized Volkswagen Service Facility. There is a malfunction in a
control module. It is not possible to open or close the convertible top.
Use the emergency procedure to close an open convertible top if neces-
sary .
Continue
convertible
top operation
The opening or closing process was interrupted. Press the button
⇒ fig. 30 (A) again until the opening or closing process has finished.
Convertible
top operation
This text message indicates the convertible top is currently opening or
closing. Press and hold the button ⇒ fig. 30 (A) again until the opening or
closing process has finished.

The instrument cluster displays and their arrangement may vary depending on the vehicle model
and engine. For displays without warning and information messages, malfunctions are only signaled
with indicator lights.
General information
Checklist
Perform the following preliminary requirements each time before opening or closing the con-
vertible top:
1. Park the vehicle a safe distance from moving traffic.
2. Park the vehicle so that it is as level as possible. The vehicle must not be on a hoist, it must not
have one side parked on a curb, and it must not be raised on a vehicle jack.
3. Remove all objects from the convertible top.
4. Remove all objects from the area of the convertible top compartment.
5. Remove ice and snow from the convertible top before opening.
6. Do not operate the convertible top in temperatures below 15 °F (-10 °C).
7. Allow the convertible top to dry completely before opening.
Checklist
The following technical requirements must be met to open or close the convertible top:
¥ The ignition must be switched on
¥ The vehicle speed must be no more than 30 mph (50 km/h).
¥ The outside temperature must be above 15 °F (-10 °C).
¥ The battery must have enough charge.
If any changes have been made in the operation of the convertible top compared with its original
factory condition, Volkswagen strongly urges you to take the vehicle to an authorized Volkswagen
dealer or other authorized Volkswagen Service Facility to have the top restored to its original condi-
tion. Mechanical changes and changes to the vehicle software must be entered in the
⇒ Booklet Warranty and Maintenance.
WARNING
Disregarding the safety-related checklist may lead to accidents and serious personal injuries.
x Always review and follow the checklist. Follow accepted safety practices and use common
sense.

Opening and closing the convertible top

Fig. 30 In the roof console: convertible top button.
You can open or close the convertible top at speeds up to 30 mph (50 km/h). If the convertible top has
already begun opening or closing, it will stop if you exceed that speed. You can only continue opening
or closing the convertible top once the vehicle speed drops below about 30 mph (50 km/h).
For safety reasons, Volkswagen recommends opening or closing the convertible top only when the
vehicle is stationary and parked at a safe distance from moving traffic ⇒ .
Opening the convertible top
x Please note and follow the steps described in the checklists
x Switch on the ignition, if necessary
x Press and hold the button ⇒ fig. 30 in the roof console until all windows go down and the convert-
ible top is completely open ⇒ . A chime sounds and the indicator light in the instrument cluster
goes out when the process is complete. A message may also appear in the instrument cluster display.
x Secure the convertible top cover (boot), if necessary
Closing the convertible top
x Please note and follow the steps described in the checklists
x Switch on the ignition, if necessary
x Remove the convertible top cover (boot), if necessary
x Pull and hold the button until the convertible top and all windows close completely ⇒ : a chime
sounds and the indicator light in the instrument cluster goes out. A message may also appear in the
instrument cluster display.
Interrupting convertible top operation
Releasing the button interrupts convertible top operation ⇒ .

The convertible top button does not work when the convertible top cover is installed. If the button
is pressed anyway, the convertible top indicator light will blink as long as the button is pressed.
What to do if the convertible top will not move

Description Possible solution
The convertible top
will not open or close.
– Check to make sure all the preliminary requirements for convertible top
operation are met
– If the convertible top still will not operate, use the emergency procedure to
close the convertible top, if necessary
– Have the system checked by an authorized Volkswagen dealer or an
authorized Volkswagen Service Facility.
The convertible top
stops when opening
or closing.
– Check the instrument cluster display for information on what to do ⇒ table.
– Pull the button ⇒ fig. 30 to completely close and latch the convertible top.
– If the convertible top does not close completely and latch, try to close and
latch it using the emergency closing procedure
– Get professional help if necessary and have the system checked by an
authorized Volkswagen dealer, an authorized Volkswagen Service Facility,
or another qualified workshop.

Automatic Rollover Support System

Fig. 35 Behind the rear bench seat backrest: Automatic Rollover Support System.
The Automatic Rollover Support System® works with the reinforced windshield frame, properly worn
safety belts, and the airbag system, to help protect vehicle occupants in a rollover accident.
If the Automatic Rollover Support System is triggered, 2 supports behind the rear seat backrest deploy
upwards in a fraction of a second.
The Automatic Rollover Support System works only when the ignition is switched on. It deploys when
the convertible top is open as well as when it is closed.
The Automatic Rollover Support System is electronically controlled together with the airbag system. A
malfunction in the rollover support system is indicated by the airbag indicator light t in the instrument
cluster

The Automatic Rollover Support System can only deploy one time. After the Automatic Rollover Sup-
port System has deployed, you cannot slide it back into its original position. It must be replaced by an
authorized Volkswagen dealer or an authorized Volkswagen Service Facility.
The Automatic Rollover Support System may deploy in the following situations:
x In driving situations in which the vehicle tips sharply to one side, consistent with the values pro-
grammed into the electronic control module.
x In certain frontal, side, and rear-end collisions.
x In rollovers.
x If the vehicle briefly leaves the ground, for example when cresting a hill at a comparatively high
speed.
WARNING
The Automatic Rollover Support System can cause serious injuries if persons or objects are
in the way when it deploys.
x Never use accessory seat covers or protective covers that block the rollover protection
deployment area.
x Every rear seat passenger must be properly seated on a seat of his or her own and must
stay in a proper seating position at all times.
x Always keep the area around the supports free of anything that could interfere with their
deployment or fly about and injure occupants when the supports deploy.
x Never take the covers off the Automatic Rollover Support System.
x Never attach a child seat, child restraints, straps, or anything else to the rollover protec-
tion supports.
WARNING
If there is a system malfunction, the Automatic Rollover Support System may cause serious
injuries by not deploying properly, by not deploying at all, or by deploying unexpectedly.
x If a malfunction exists in the system, have it checked immediately by an authorized
Volkswagen dealer or an authorized Volkswagen Service Facility. A malfunction exists in the
system if the indicator light:
– does not come on when the ignition is turned on;
– does not go out about 5 seconds after you start the engine;
– goes out after switching on the ignition and then comes back on again;
– comes on or flickers when you are driving.
NOTICE
If deployed, the Automatic Rollover Support System can damage the convertible top fabric
when opening or closing the top.
x Do not open or close the convertible top if the Automatic Rollover Support System has
deployed.

Function Action for seat heating ⇒fig.44
Switch on: Press the Aor ebutton. Seat heating is switched on
to maximum.
Adjust the heating
level:
Press the Aor e button repeatedly until the desired
heating level is set.
Switch off: Press the A or e button repeatedly until all indicator
lights in the button are off.

Special seat heating features
On the driver and the passenger side, the seat heating may resume at the setting that was set when
the ignition was switched off. However, this feature only works if the key is not taken out of the ignition
switch, or, for vehicles with Keyless Access, the driver door is not opened or the vehicle is not locked.
People suffering from a low level of perceived pain or a lowered awareness of pain as from medica-
tion, paralysis, or chronic illness (e.g. diabetes) should NEVER use the seat heating feature ⇒ !
The use of seat heating by persons with these conditions could result in burns to the back, buttocks,
and legs that may take a long time to heal and may never heal completely. If you have any of these
conditions, you should take regular breaks and get out of the vehicle, particularly on long trips. Consult
your doctor for advice regarding your specific condition.
WARNING
Certain medical conditions, such as paralysis and diabetes, and certain medications can
increase the risk of serious burns when the seat heating feature is switched on.
x Vehicle occupants who have a low level of perceived pain or a lowered awareness of pain
can receive serious burns to the back, buttocks, and legs that take a long time to heal or may
never heal completely.
x Never use the seat heating feature if you or your passengers are at risk of being burned
because of a medical condition. Take regular breaks and get out of the vehicle, particularly
on long trips. Consult your doctor for advice regarding your specific condition.
x Never let exposed skin remain in contact with the seat upholstery when the seat heating is
being used.
WARNING
A wet seat can cause the seat heating to malfunction and increase the risk of serious burns.
x Always make sure the seats are dry before using the seat heating.
x Never sit on the seat with wet clothes.
x Never put damp or wet things including clothes on the seat.
x Never spill liquids on the seats.
NOTICE
x To help prevent damage to electrical and other parts in the seat, do not kneel on the front
seats or apply concentrated pressure to a small area of the seat or backrest.
x Liquids, sharp objects and things that do not let the heat in the seat escape into the air,
including, for example, a child restraint, a blanket, or seat covers on the seat can damage seat
heating.

A warning chime also sounds.
The safety belt warning light ª comes on for 6 seconds when the ignition is switched on. A warning
chime also sounds for up to 6 seconds if the driver's safety belt is not buckled. The chime stops soon-
er if the driver buckles his or her safety belt. The warning light and the chime go out when both driver
and front passenger have bucked their safety belts.
If the driver and front seat passenger do not both fasten their safety belts within about 24 seconds
after the chime stops and the vehicle is moving at a speed of more than about 15 mph (25 km/h), the
chime will again sound for about 6 seconds, then go off for about 24 seconds, then sound again for
about another 6 seconds. The same thing happens if one of the safety belts is fastened and then
unfastened while the vehicle is moving. The safety belt warning light ª also flashes. The warning
chime continues to sound at 24 second intervals for up to 2 minutes. No chime sounds at speeds of
less than about 5 mph (8 km/h).
If the ignition is switched on, the safety belt warning light ª stays on until the driver and front passen-
ger have both buckled their safety belts.
WARNING
Not wearing a safety belt or wearing an improperly positioned safety belt increases the risk of
severe personal injury or death. Safety belts offer optimum protection only when used cor-
rectly.
Frontal collisions and laws of physics

Fig. 46 A vehicle with passengers not wearing safety belts approaches a wall.

Fig. 47 A vehicle with passengers not wearing safety belts hits a wall.
Please first read and note the introductory information and heed the WARNINGS

Lights
up Possible cause Proper response
 One or more driving lights not working.
Replace burned out bulb , or
If all light bulbs are OK, see an authorized
Volkswagen dealer or authorized
Volkswagen Service Facility.

Fog lights switched on (indicator light on
the headlight switch or the instrument
cluster).




Left or right turn signal.
The indicator light blinks twice as fast if a
turn signal is not working on the vehicle.
Check the turn signals on the vehicle.
 High beams switched on or headlight
flashers in use.

When the ignition is switched on, several warning and indicator lights come on briefly for a function
check. They go out after a few seconds.
WARNING
Failure to heed warning lights and instrument cluster text messages can cause the vehicle to
break down in traffic and result in a collision and serious personal injury.
x Never ignore warning lights or text WARNINGS.
x Always stop the vehicle as soon as it is safe to do so.
x Whenever stalled or stopped for repair, move the vehicle a safe distance off the road, stop
the engine, turn on the emergency flashers, and use other warning devices to warn
approaching traffic.
x Never park the vehicle in areas where the hot catalytic converter and exhaust system can
come into contact with dry grass, brush, spilled fuel, oil, or other material that can catch fire.
x A broken down vehicle presents a high accident risk for itself and others. Switch on
emergency flashers and set up a warning triangle to warn oncoming traffic.
NOTICE
Failure to heed warning lights or text WARNINGS can result in vehicle damage.
High Intensity Discharge (HID) headlights provide bright, uniform lighting to help you see and be
seen. The light comes from an electric arc between two electrodes in the gas-filled bulb. Over time, the
electrodes can wear down and the gap between them will get wider. The HID lamp’s control unit then
increases the voltage to keep the arc’s brightness constant. However, the commonly called “Xenon”
bulbs will also ultimately burn out. Before they burn out, HID lamps can flicker. A message will then
appear in the MFI. This is your reminder to see an authorized Volkswagen dealer or an authorized
Volkswagen Service facility to check the headlights.

Acoustic warning when lights are not switched off
In the following situation, a warning chime will sound if you take the key out of the ignition and open
the driver door. This is to remind you that lights are still on.
x Light switch in position .
WARNING
Daytime running lights are not bright enough to let you see ahead or be seen by others when
it is dark.
x Always switch on the low-beam headlights at dusk or when it is dark and whenever the
weather is bad or visibility is poor.
x Never use the daytime running lights to see where you are going. They are not bright
enough and will not let you see far enough ahead for safety, especially at dusk or when it is
dark. Always switch on the low-beam headlights at dusk or when it is dark.
x The taillights do not come on with the daytime running lights. Unless the taillights are on,
a vehicle cannot be seen by others in bad weather, at dusk, or when it is dark.
In cool or humid weather, the insides of the headlights, the rear lights, and turn signals can
temporarily fog up. This is normal and does not affect the service life of the vehicle's lighting system.
Applicable only in the United States
Lights and vision features

Glove and luggage compartment lights
The glove and luggage compartments may have lights that come on automatically when they are
opened and go off when they are closed.
Background lighting
When the ignition and headlights are switched on, the background lighting in the roof console lights
up.
There may also be footwell lighting.
Background lighting in the doors
The background lighting in the doors comes on when the ignition or headlights are switched on.

Turn the thumbwheel to the desired position ⇒ fig. 74:
Position Background lighting color
R Red
B Blue
W White
– Background lighting switched off

The interior and reading lights go out when you lock the vehicle or a few minutes after you
remove the vehicle key from the ignition. This helps to prevent unnecessary drain on the vehicle
battery.