ABS VOLKSWAGEN BORA 1998 Service Manual

Downloaded from www.Manualslib.com manuals search engine 01-280


1. Check DTC memory (Function 02)
2. Erase DTC memory (Function 05)
3. End output (Function 06)
4. Switch off ignition.
5. Switch on ignition.
6. Perform zero compensation again.

-
Press key.
Rapid data transfer HELP
Enter address word XX Indicated on display:
- Press keys 0 and 6, this ends the output.
Rapid data transfer Q
06 - End output Indicated on display
ABS and ESP warning lights light up for
approx. 2 seconds.
Стр. 122из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-282


Rapid data transfer Q
04 - Basic settin
g
Indicated on display:
- Confirm entry with key Q.
Basic setting HELP
Enter dis
play group number XXX
Indicated on display:
- Press keys 0, 6 and 9
- Confirm entry with key Q.
ABS warning light flashes.
Basic setting 69 OFF <4-ON>
Compens. OK 0.3m/s2 Indicated on display:
Note:
After successfully completing the zero
compensation the values in display do not
go to 0.00 m/s2
Function is unknown or cannot be
-
performed at moment
If this display appears the login procedure
has not been performed successfully.
- or:
Basic setting 69 OFF <4-ON>
Compens. n. poss. 5.0m/s2 If this appears on display, the measured
values are not within the accepted tolerance
for zero compensation.
- Check measured values with help of
function 08 "Read measured value block"
Page 01
-240 , Display group number
006.
Стр. 124из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-283


1. Check DTC memory (Function 02)
2. Erase DTC memory (Function 05)
3. End output (Function 06)
4. Switch off ignition.
5. Switch on ignition.
6. Perform zero compensation again.

-
Press key.
Rapid data transfer HELP
Enter address word XX Indicated on display:
- Press keys 0 and 6, this ends the output.
Rapid data transfer Q
06 - End output Indicated on display
ABS and ESP warning lights light up for
approx. 2 seconds.
Стр. 125из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-285



- Confirm entry with key Q.
Basic setting 93 ON <8>
S
ystem test activated OK
Indicated on display:
The ESP driving test is activated.
ABS warning light -K47- lights up.
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display:
This completes the stationary comparison
test. - Disconnect diagnostic connector.
- Start engine.
- Depress brake pedal firmly (brake
pressure of more than 35 bar) until the
ESP Control Lamp -K155- flashes.
Стр. 127из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-286



- Now perform test drive for maximum 50 seconds
at a speed of 15km/h...30km/h:

It must be driven so that no ABS, EDL, ASR or
ESP regulation is performed.

Make a turn with steering wheel turned at least
90 .
When the ABS warning lamp -K47- and ESP
warning lamp -K155- go out, the ESP driving
test has been successfully completed.

WARNING!

Always comply with road traffic regulations
and drive according to the traffic conditions.

Note:

If the ABS warning light -K47- does not go out,
then the ESP driving test has not been
performed correctly.

If the ABS warning light -K47- does not go out
and the ESP control lamp -K155- lights up
again, check DTC memory Page 01
-170 .
Стр. 128из 129 On Board Diagnostic (OBD), performing

Downloaded from www.Manualslib.com manuals search engine 01-289



The test steps Page 01-297 apply only to
vehicles with ABS/EDL/ASR/ESP
For vehicles on which the On Board Diagnostic
(OBD) does not give any indication of the
source of the malfunction. Work through the
complete electrical check.

For vehicles on which the OBD provides a
direct indication of the source of the
malfunction. Only carry out the test steps
recommended in the DTC table (directed entry).
An overview of all the test steps in the electrical
check Page 01
-297 .
Стр. 2из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-290



Test prerequisites

Switch ignition and electrical
consumers off before commencing the
check (headlights, lighting, fans ...).

Fuses must be OK (remove fuses from
fuse holder to check).
Electrical Wiring Diagrams,
Troubleshooting & Component
Locationsbinder

- Pull fuse holder out of cable channel.
- Release ABS Control Module (w/EDL) -
J104- connector -arrow 1- and pull off -
arrow 2-.
Стр. 3из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-291



The specified values are matched to the
V.A.G 1526 and are not necessarily
applicable for other test modules. - Connect test box V.A.G 1598/36 -1- to
multi-pin connector of ABS control
module (w/EDL) -J104- -2-.
Стр. 4из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine 01-292


Multi-pin connector with contact
assignments


Note:
All contacts not listed are currently not
assigned and must never be connected to
other components!
Contact assignment of connectors for
voltage supply and self-diagnosis with
the V.A.G 1551 scan tool
Contact
4 = Ground (terminal 31)
Contact
16 = Positive (terminal 30)
Contact
7 = K wire to contact 2 of multi-
pin connector T47 of ABS
control module (w/EDL) -
J104-
Contact assignment of connector T47
wiring harness/ABS control module
(w/EDL) -J104-
Стр. 5из 38 Electrical check of Mark 60

Downloaded from www.Manualslib.com manuals search engine
01-293


Contact
Wiring connection to component ...
1
Voltage supply fr om battery +
2
Connector T16/7, K wire
3

Longitudinal acceleration sens or -G251- sensor wire(4MOTION vehicles only)
Vacant (4MOTION vehicles with ESP-sensor unit -G419, vehicles from 11.01)
4
Voltage supply from igni tion/starter switch
5

Longitudinal acceleration se nsor -G251- Ground(4MOTION vehicles only)
Vacant (4MOTION vehicles with ESP-sensor unit -G419- , vehicles from 11.01)
6

Sensor for transverse acceleration -G200-
Voltage supply for ESP-sensor unit -G419-, vehicles from 02.02
7

Longitudinal acceleration se nsor -G251- voltage supply(4MOTION vehicles
only)
Vacant (4MOTION vehicles with ESP-sensor unit -G419- , vehicles from 11.01)
8
Vehicles with navi gation system only
9
Coding bridge to contact 12 (vehicle s with ABS/EDL/ASR/ESP 4MOTION
only)
10
Vehicles with navi gation system only
11
Data bus wire Wiring diagrams
12
Coding bridge to contact 9 (vehicles with ABS/EDL/ASR/ESP 4MOTION only)
Coding bridge to contact 38 (vehicles with ABS/EDL/ASR/ESP front wheel
drive only)
Стр. 6 из 38
Electrical check of Mark 60
Volkswagen Technical Site: http://v olkswagen.msk.ru http://vwts.info http://vwts.ru
огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi