oil capacities VOLKSWAGEN CORRADO 1993 Repair Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1993, Model line: CORRADO, Model: VOLKSWAGEN CORRADO 1993Pages: 920, PDF Size: 6.92 MB
Page 323 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 9)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
process is completed, the amount of compressor oil removed must be
measured and the same amount added to A/C system.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when tightening or
loosening fittings. Some refrigerant lines are connected with a
coupling. Special tools may be required to disconnect lines. Cap or
plug all openings as soon as lines are removed. DO NOT remove caps
until connections of lines and fittings are completed.
CONNECTING LINES & FITTINGS
NOTE: All R-134a based systems use 1/2-16 ACME threaded fittings.
Ensure all replacement parts match the connections of the
system being worked on.
Always use a new gasket or "O" ring when connecting lines or
fittings. Coat "O" ring with refrigerant oil and ensure it is not
twisted during installation. Always use 2 wrenches to prevent damage
to lines and fittings.
PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, evacuate system thoroughly with a
vacuum pump. Charge system with proper amount of refrigerant and
perform leak test. See REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS
article in GENERAL SERVICING for system capacities. Check all fittings
that have been opened. After system has been leak tested, check system
performance.
NOTE: Most compressors are pre-charged with a fixed amount of
refrigerant (shipping) oil. Drain compressor oil from new
compressor and add refrigerant oil to new compressor
according to amount removed from old compressor. Always
refer to underhood A/C specification label or A/C compressor
label while servicing A/C system.
ATSUGI
ROTARY VANE
1) Before checking and adjusting oil level, operate engine at
1200 RPM. Set controls at maximum cooling and high blower motor speed
for 10 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Drain compressor oil through
compressor discharge port and measure oil amount.
3) If amount drained is less than 3 ounces, conduct leak
tests at system connections. Repair or replace faulty parts as
Page 324 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 10)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
necessary. Check purity of oil and adjust oil level as follows.
4) If amount drained is 3 ounces or more, oil level is okay.
Fill with same amount drained, using new oil. If amount drained is
less than 3 ounces, pour in 3 ounces of new refrigerant oil.
COMPONENT REFRIGERANT OIL CAPACITIES (ATSUGI ROTARY VANE)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ....................................... 1.0-1.7
Evaporator ...................................... 1.5-2.5
Receiver-Drier .................................. 0.5-0.8
Refrigerant Lines (1) ........................... 1.0-1.7
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ BOSCH
6-CYLINDER
1) Before checking and adjusting oil level, operate
compressor at engine idle speed, and set controls at maximum cooling
and high blower motor speed for 20-30 minutes to return oil to
compressor.
2) Stop engine and discharge refrigerant. See SERVICING
PRECAUTIONS. Remove refrigerant oil level inspection plug on side of
compressor. Oil should be at lower lip of threaded hole. If oil level
is low, add new refrigerant oil as necessary. Replace inspection plug
and tighten to 10-12 ft. lbs. (14-16 N.m).
CALSONIC
V5 5-CYLINDER & V6 6-CYLINDER
Infiniti & Nissan
1) Before checking and adjusting oil level, operate engine at
1200 RPM. Set controls at maximum cooling and high blower motor speed
for 10 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant. See SERVICING
PRECAUTIONS. Measure the amount of oil drained/discharged into
refrigerant recovery/recycling equipment.
3) Remove compressor from vehicle. Drain compressor oil from
compressor drain plug and measure oil amount. Add this amount to
amount drained in step 2), to obtain total amount drained.
4) Fill compressor with total amount drained, using new oil.
If any major components of the system were also replaced, determine
the amount of additional oil needed. See appropriate COMPONENT
REFRIGERANT OIL CAPACITIES table for specified amount.
COMPONENT REFRIGERANT OIL CAPACITIES (CALSONIC V5)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Page 325 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 11)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Component Ounces
Condenser ........................................ 1.0-1.7
Evaporator ....................................... 1.5-2.5
Receiver-Drier ................................... 0.5-0.8
Refrigerant Lines (1) ............................ 1.0-1.7
(1) - Add only if a refrigerant oil leak is indicated.ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄCOMPONENT REFRIGERANT OIL CAPACITIES (CALSONIC V6)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................ 2.5
Evaporator ........................................... 2.5
Receiver-Drier ....................................... 0.2
Refrigerant Lines (1) ................................ 1.0
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Subaru
1) Before checking and adjusting oil level, operate engine at
1000-1500 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Drain compressor oil from
compressor drain plug and measure oil amount.
3) Fill compressor with total amount drained, using new oil.
If any major components of the system were also replaced, determine
the amount of additional oil needed. See appropriate SUBARU COMPONENT
REFRIGERANT OIL CAPACITIES table for specified amount.
SUBARU COMPONENT REFRIGERANT OIL CAPACITIES (LEGACY)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Compressor ........................................... 2.4
Condenser ............................................ 1.7
Evaporator ........................................... 2.4
Refrigerant Lines (1) ................................ 1.7
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄSUBARU COMPONENT REFRIGERANT OIL CAPACITIES (SVX)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Compressor ........................................... 2.4
Condenser ............................................ 1.7
Page 326 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 12)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
Evaporator ........................................... 2.4
Refrigerant Lines (1) ................................ 1.7
(1) - Add only if a refrigerant oil leak is indicated.ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ DIESEL KIKI
ROTARY VANE
1) Before checking and adjusting oil level, operate engine at
800-1000 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
measure amount of oil drained.
3) If amount drained is less than 3 ounces (1.7 ounces on Geo
Storm), conduct leak tests at system connections. Repair or replace
faulty parts as necessary.
4) If amount drained is more 3 ounces (1.7 ounces on Geo
Storm), oil level is okay. Fill compressor with same amount drained,
using new oil. If amount drained is less than 3 ounces (1.7 ounces on
Geo Storm), pour in 3 (1.7) ounces of new refrigerant oil.
5) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
CAPACITIES (DIESEL KIKI ROTARY VANE) table.
COMPONENT REFRIGERANT OIL CAPACITIES (DIESEL KIKI ROTARY VANE)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................... 1.7
Evaporator .............................................. 1.0
Receiver-Drier .......................................... 1.0
Refrigerant Lines ....................................... 0.3
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 5 & 6-CYLINDER
1) Before checking and adjusting oil level, operate engine at
800-1000 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
measure amount of oil drained.
3) If amount drained is less than 3 ounces, conduct leak
tests at system connections. Repair or replace faulty parts as
necessary.
4) If amount drained is more 3 ounces, oil level is okay.
Fill compressor with same amount drained, using new oil.
5) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
Page 327 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 13)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
CAPACITIES (DIESEL KIKI 5 & 6-CYLINDER) table.
COMPONENT REFRIGERANT OIL CAPACITIES (DIESEL KIKI 5 & 6-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser .................................................. 1.0
Evaporator ................................................. 1.7
Receiver-Drier ............................................. 1.0
Refrigerant Lines .......................................... 0.3
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ FORD
FX-15 10-CYLINDER
1) Slowly discharge system. See SERVICING PRECAUTIONS. Remove
A/C compressor. Drain compressor oil from suction and discharge ports.
Measure amount drained and discard oil.
2) If amount drained from removed (old) compressor is between
3 and 5 ounces, add drained amount of new refrigerant oil into the NEW
compressor through suction port.
3) If amount drained is less than 3 ounces, add 3 ounces to
the NEW compressor. If amount drained is more than 5 ounces, add 5
ounces. Use new "O" rings on refrigerant lines. Install A/C
compressor. Evacuate and recharge system. Perform leak test.
4) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
CAPACITIES (FX-15 10-CYLINDER) table.
COMPONENT REFRIGERANT OIL CAPACITIES (FX-15 10-CYLINDER)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................ 1.0
Evaporator ........................................... 3.0
Receiver-Drier ................................... (1) 2.0
Refrigerant Lines ................................ (2) 1.0
(1) - On Hyundai Sonata and Mazda Navajo, drain oil from old
receiver-drier. Add amount drained to amount specified.
(2) - Add only if a large oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ HADSYS
7-CYLINDER
Honda (Accord)
1) Discharge system. See SERVICING PRECAUTIONS. Remove
compressor from vehicle. Drain all oil from NEW compressor and fill
compressor with 4 ounces of clean refrigerant oil.
Page 328 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 14)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
2) Add one ounce of refrigerant oil when replacing
evaporator. Add1/2 ounce when replacing condenser. When replacing
receiver-drier or hoses, add 1/3 ounce per component replaced.
HARRISON
R4 4-CYLINDER
1) Before checking and adjusting oil level, operate engine at
800-1000 RPM. Set controls at maximum cooling and high blower motor
speed for 20 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
measure amount of oil drained.
3) If amount drained is less than one ounce, conduct leak
tests at system connections. Repair or replace faulty parts as
necessary. Fill compressor with 2 ounces, using new refrigerant oil.
4) If amount drained is more one ounce, oil level is okay.
Fill compressor with same amount drained, using new oil.
5) When replacing other A/C system components, add the
following amount(s) of refrigerant oil. See COMPONENT REFRIGERANT OIL
CAPACITIES (HARRISON R4 4-CYLINDER) table.
COMPONENT REFRIGERANT OIL CAPACITIES (HARRISON R4 4-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................... 1.0
Evaporator .............................................. 1.7
Receiver-Drier .......................................... 1.0
Refrigerant Lines ....................................... 0.3
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ V5 5-CYLINDER
1) If system is operable, run A/C system for several minutes
to stabilize system. Turn off engine. Discharge system and remove
compressor. See SERVICING PRECAUTIONS. Remove drain plug and measure
oil.
2) If one ounce or more is drained, add same amount. If less
than one ounce is drained, add 2 ounces of new refrigerant oil to
compressor.
3) If condenser is replaced, add one ounce. Add 3.5 ounces if
accumulator is replaced. If evaporator is replaced or if a large
refrigerant leak occurred, add 3 ounces of new refrigerant oil.
HITACHI
6-CYLINDER
1) Before checking and adjusting oil level, operate
compressor at 1000-1500 engine RPM, and set controls at maximum
Page 332 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 18)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
component replaced.
Honda
1) Discharge system. See SERVICING PRECAUTIONS. Remove
compressor from vehicle. Drain all oil from NEW compressor and fill
compressor with 4 ounces of clean refrigerant oil.
2) On Civic and Civic Del Sol, add 1 1/2 ounce of refrigerant
oil when replacing evaporator. Add 2/3 ounce when replacing condenser.
When replacing receiver-drier or hoses, add 1/3 ounce per component
replaced.
3) On Prelude, add one ounce of refrigerant oil when
replacing evaporator. When replacing other A/C components, add 1/3
ounce per component replaced (including hoses).
Hyundai
Add 1 1/2 ounces of refrigerant oil when replacing
evaporator. Add one ounce when replacing condenser. When replacing
receiver-drier, add 1/3 ounce of refrigerant oil.
5-CYLINDER
Mazda
Add one ounce of refrigerant oil when replacing condenser.
Add 1 2/3 ounce when replacing evaporator. When replacing receiver-
drier, add 1/2 ounce of refrigerant oil.
NOTE: Saab and Volvo (Sanden 5 or 7-cylinder) compressor oil
checking procedures are not available from manufacturer.
7-CYLINDER
Hyundai & Mitsubishi (Excel & Precis)
1) Before checking and adjusting oil level, operate
compressor at engine idle speed, and set controls at maximum cooling
and high blower motor speed for 20-30 minutes to return oil to
compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS. Remove oil drain plug and
drain oil. Measure amount of oil drained. Install drain plug with new
"O" ring.
3) If amount drained is 2.3 ounces or more, fill compressor
with same amount using new oil. If amount drained is less than 2.3
ounces, fill with 2.3 ounces. Install filler plug. Install compressor
and recharge system.
COMPONENT REFRIGERANT OIL CAPACITIES (SANDEN 7-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser ............................................ 1.0
Evaporator ............................................. 3
Receiver-Drier ......................................... 1
Page 333 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 19)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PMÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Jaguar (XJS)
1) Operate engine at idle speed for 10 minutes, to return
refrigerant oil to compressor. Stop engine. Discharge refrigerant. See
SERVICING PRECAUTIONS. Clean area around compressor filler plug and
remove plug slowly.
2) Determine angle at which compressor is mounted. Insert
compressor dipstick diagonally until stop on dipstick contacts filler
plug surface. See Fig. 1. Remove dipstick and note oil fill level.
Each increment on dipstick represents one ounce of oil.
3) Determine amount of oil needed according to mounting
angle. See COMPRESSOR OIL CAPACITIES (JAGUAR XJS) table for specified
amount.
4) If necessary, correct compressor oil level. Install
compressor oil plug, and tighten it to 72-108 INCH lbs. (8-12 N.m).
Evacuate and recharge A/C system. Perform leak test.Fig. 1: Checking Jaguar XJS Compressor Oil Level (Sanden 7-Cylinder)
Courtesy of Jaguar Cars, Inc.
COMPRESSOR OIL CAPACITIES (JAGUAR XJS)
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄMounting Angle (In Degrees) Oil Level In Increments
0 .................................................... 3-5
10 ................................................... 4-6
20 ................................................... 5-7
30 ................................................... 6-8
40 ................................................... 7-9
50 .................................................. 8-10
60 .................................................. 9-11
90 ................................................. 10-12
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Volkswagen
1) The use of refrigerant recovery/recycling is recommended
Page 334 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 20)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
by manufacturer. After refrigerant recovery process is completed, the
amount of compressor oil removed must be measured and the same amount
added to A/C system.
2) On Cabriolet, add 2/3 ounce of refrigerant oil when
replacing evaporator. When replacing condenser or receiver-drier, add
1/3 ounce of refrigerant oil per component replaced.
3) On Corrado SLC, Golf, GTI, Jetta and Passat, add 2/3 ounce
of refrigerant oil when replacing evaporator. When replacing condenser
or receiver-drier, add 1/3 ounce of refrigerant oil per component
replaced.
4) On EuroVan, add one ounce of refrigerant oil when
replacing evaporator. Add 1/2 ounce when replacing condenser (2/3
ounce on vehicles with rear A/C). When replacing receiver-drier, add
1/3 ounce (2/3 ounce on vehicles with rear A/C).
SEIKO-SEIKI
ROTARY VANE
Saab (9000)
The A/C system is filled with 6.6 ounces of compressor oil.
The compressor must be topped off with the specified amount. See
COMPONENT REFRIGERANT OIL CAPACITIES (SEIKO-SEIKI ROTARY VANE) table.
Topping off should be carried out on the high pressure side of the
compressor.
COMPONENT REFRIGERANT OIL CAPACITIES (SEIKO-SEIKI ROTARY VANE)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Compressor .......................................... (1) 2.3
Condenser ............................................... 1.3
Expansion Valve ......................................... 0.6
Evaporator .............................................. 1.3
Receiver-Drier .......................................... 1.3
Refrigerant Lines ....................................... 0.6
(1) - To avoid an excessive amount of oil in the A/C system, oil
must be drained from the compressor before it is installed.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ZEXEL
NOTE: Isuzu and Subaru compressor oil checking procedures are not
available from manufacturer.
ROTARY VANE
Nissan
1) Before checking and adjusting oil level, operate engine at
1200 RPM. Set controls at maximum cooling and high blower motor speed
for 10 minutes to return oil to compressor.
Page 335 of 920
A/C COMPRESSOR OIL CHECKING
Article Text (p. 21)
1993 Volkswagen Corrado
For Volkswagen Technical Site: http://vw.belcom.ru
Copyright © 1998 Mitchell Repair Information Company, LLC
Wednesday, March 22, 2000 08:47PM
2) Stop engine. Discharge refrigerant. See SERVICING
PRECAUTIONS. Measure the amount of oil drained/discharged into
refrigerant recovery/recycling equipment.
3) Remove compressor from vehicle. Drain compressor oil from
compressor drain plug and measure oil amount. Add this amount to
amount drained in step 2), to obtain total amount drained.
4) Fill compressor with total amount drained, using new oil.
If any major components of the system were also replaced, determine
the amount of additional oil needed. See COMPONENT REFRIGERANT OIL
CAPACITIES (ZEXEL ROTARY VANE & 6-CYLINDER) table for specified
amount.
COMPONENT REFRIGERANT OIL CAPACITIES (ZEXEL ROTARY VANE & 6-CYLINDER)ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄComponent Ounces
Condenser
Altima & Maxima ............................................... 2.5
NX, Pickup, Sentra & 300ZX ................................ 1.0-1.7
Evaporator
Altima & Maxima ............................................... 2.5
NX, Pickup, Sentra & 300ZX ................................ 1.5-2.5
Receiver-Drier
Altima & Maxima ............................................... 0.2
NX, Pickup, Sentra & 300ZX ................................ 0.5-0.8
Refrigerant Lines (1) .......................................... 1.0
(1) - Add only if a refrigerant oil leak is indicated.
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 6-CYLINDER
Audi
1) The use of refrigerant recovery/recycling is recommended
by manufacturer. After refrigerant recovery process is completed, the
amount of compressor oil removed must be measured and the same amount
added to A/C system.
2) Add one ounce of refrigerant oil when replacing
accumulator. When replacing condenser, add amount drained from
condenser plus 1/3 ounce of refrigerant oil. When replacing
evaporator, add amount drained from evaporator plus 2/3 ounce of
refrigerant oil.
Nissan
1) Before checking and adjusting oil level, operate engine at
1200 RPM. Set controls at maximum cooling and high blower motor speed
for 10 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant. See SERVICING
PRECAUTIONS. Measure the amount of oil drained/discharged into
refrigerant recovery/recycling equipment.
3) Remove compressor from vehicle. Drain compressor oil from
compressor drain plug and measure oil amount. Add this amount to