Page 55 VOLKSWAGEN ID.4 2020 Owner´s Manual

Fuses in the bonnet space
Please refer to and at the start of
the chapter on page 296. Fig. 160
In the bonnet space: fuse bo x with
plastic grippers.
Opening the fuse box in the bonnet space

x
If the power supply of the towed v ehicle
fails, stop towing immediately and seek
expert assistance. NOTICE
Towing with a tow-rope or tow-bar can dam-
age the v
ehicle.
x Tow the vehicle carefully with a tow-rope
or tow-bar.
x If possible, have the broken-down vehicle
transported by a breakdown truck. NOTICE
When pushing the vehicle by hand, the tail
light clusters, side spoilers on the rear win-
dow and large panels can be damaged and
the rear spoiler may become detached.
x When pushing the v

ehicle by hand, do not
press on the tail light clusters, side spoilers
on the rear window, large panels and the
rear spoiler. NOTICE
The vehicle can be damaged, e.g. the vehicle
paintwork, when remo
ving and fitting the
cover and towing eye.
x Remove and install the cover and the tow-
ing eye carefully so as to avoid damage to
the vehicle. NOTICE
Use of a towing eye that is not suitable for
the v
ehicle can damage the vehicle.
x Always use the towing eye supplied in the
vehicle toolkit of your vehicle or a towing
eye that is suitable for the vehicle for tow-
ing. Notes on towing
Please refer to and at the start of
the chapter on page 304.
It is still possible to activ

ate the turn signals
in a vehicle that is being towed, even if the
hazard warning lights are switched on. To do
this, operate the turn signal and main beam
lever in the required direction while the igni-
tion is switched on. The hazard warning lights
will not flash while the turn signal is being
used. The hazard warning lights will start
flashing again automatically as soon as the
turn signal and main beam lever is moved
back to the neutral position.
In which situations may the vehicle not be
towed?
In the following situations, the vehicle may
not be towed for a long distance on its own
tyres:

port company, that your vehicle is electrically
driv
en. Towing
Please refer to and at the start of
the chapter on page 304.
Preparations

Fitting the towing eye at
front
Please refer to and at the start of
the chapter on page 304. Fig. 169
In the front bumper on the right: re-
mo ving the cover. Fig. 170
In the front bumper on the right:
screwing in the towing eye.
The towing eye must always be kept in the
v

ehicle.
Comply with the notes on towing

WARNING
Insufficient anti-freeze in the cooling sys-
tem of the v ehicle can cause the electric
drive to break down and thereby cause se-
rious injuries.
x The amount of correct coolant additive
used must be sufficient for the lowest
ambient temperature that you expect
the vehicle to be exposed to.
x Coolant can freeze at extremely cold
outside temperatures, causing the vehi-
cle to break down. Vehicle occupants
with inadequate winter clothing could
then freeze to death as the heating will
also no longer function. NOTICE
Never mix genuine coolant additives with
other coolants that ha
ve not been approved
by Volkswagen.
x If the liquid in the coolant expansion tank
is not pink (colouring results from mixing
the purple coolant additive with distilled
water) but for example brown instead of
purple, the suitable coolant has been
mixed with an unsuitable coolant additive.
The coolant must be changed as soon as
possible if this is the case. Failure to ob-
serve this warning can result in serious
malfunctions or damage to the electric
drive and cooling system. Coolant and coolant additives can pol-
lute the en

vironment. Spilt service flu-
ids must be collected and disposed of proper-
ly and with respect for the environment. Checking the coolant level
and refilling coolant
Please refer to , and on page 309
and at the start of the chapter on page
315. Fig. 179
Under the bonnet: markings on the
coolant e
xpansion tank. Fig. 180
Under the bonnet: coolant e
xpansion
tank cap (illustration).
Preparations
1. Park the vehicle on a firm and level sur- face.
2. Allow the electric drive to cool down

cooling system when the engine is hot and
could cause damage.
x If a large amount of coolant has been lost,
do not refill the coolant until the engine
has cooled completely. Hea
vy coolant loss
is an indication of leaks in the cooling sys-
tem. The cooling system should be
checked by a qualified workshop as soon
as possible. Failure to do so can result in
engine damage.
x Do not refill coolant if there is no more
coolant in the coolant expansion tank. Air
could have entered the cooling system. Do
not drive on! Seek expert assistance. Fail-
ure to do so can result in engine damage.
x When refilling service fluids, please ensure
that you pour the correct service fluids in-
to the correct openings. The use of incor-
rect service fluids can result in serious
malfunctions and damage to the electric
drive. Troubleshooting
Please refer to , and on page 309
and at the start of the chapter on page
315. Coolant
The indicator lamp flashes red.
Engine coolant temperature too high or en-
gine coolant le

vel too low. Do not driv

e on!
Stop the vehicle as soon as possible and
when safe to do so.

OR: to cancel the operation, touch
Cancel . The current tyre pressure is not
sa
ved and the system will not be re-
synchronised.
After an extended driving time (at least 20
minutes) with driving at different speeds, the
system will automatically learn the new val-
ues and monitor them. Troubleshooting for Tyre
Pressure Loss Indicator
Please refer to at the start of the chap-
ter on page 325. Low tyre pressure
The indicator lamp lights up yellow.
There is a loss of pressure in one or more
tyres or the tyre is structurally damaged.

come loose, leading to a loss of control of
the v
ehicle, causing accidents and serious
injuries.
x Never drive if wheel bolts are missing or
loose.
x Always use wheel bolts that match the
wheel rims and the vehicle type.
x Always tighten the wheel bolts with the
correct tightening torque. If you do not
have a torque wrench, tighten the wheel
bolts with the wheel bolt wrench and
have the torque checked without delay
by the nearest qualified workshop. Handling wheels and tyres
Please refer to at the start of the chap-
ter on page 328. Fig. 182
Illustration: diagram f
or rotating
wheels when all wheels have the same tyre and
rim sizes.
The wheels and tyres approved by Volkswa-
gen have been carefully selected.
Rotating wheels when all wheels have the
same tyre and rim sizes
If all wheels have the same tyre and rim sizes,
it is recommended to regularly rotate the
wheels in accordance with the diagram

WARNING
Wheels must have the necessary clearance.
If the wheels do not ha ve the necessary
clearance, the tyre could rub on parts of
the running gear, the vehicle body and the
brake lines. This can lead to a fault in the
brake system and to tread separation and
thus to a tyre bursting.
x The actual tyre size must not exceed the
tyre dimensions of manufacturers ap-
proved by Volkswagen and must not rub
on any vehicle body parts. NOTICE
Avoid heavy impacts and drive round obsta-
cles whene
ver possible. Tyres can be de-
formed in particular by potholes and kerb
edges. This can cause damage to the tyres
and wheel rims. NOTICE
Do not damage the valves when fitting dif-
f
erent tyres. Never drive without valve caps.
This could cause damage to the valves. Old tyres should be disposed of prop-
erly and as required by legislation.
If the spare tyre is not the same as the
tyres that are mounted on the car - f

or
example in the case of winter tyres or a tem-
porary spare wheel - only use the spare tyre
in the event of a breakdown for a short peri-
od of time and drive with extra care. Refit the
normal road wheel as soon as possible.
Volkswagen-approved tyres are guar-
anteed to have the dimensions that are
suitable for the vehicle. In the case of other
tyres, the tyre seller must provide a certifi-
cate from the tyre manufacturer stating that
the tyre is also suitable for the vehicle. This
certificate must be stored in a safe place in
the vehicle. Wheel rims and wheel bolts
Please refer to at the start of the chap-
ter on page 328.
Wheel rims, tyres and wheel bolts are match-
ed to the v

ehicle type. If different wheel rims
are fitted, the correct wheel bolts with the
correct length and correctly shaped bolt
heads must be used. This ensures that the
brakes work properly and that the vehicle
drives quietly and safely.
For technical reasons, it is not generally pos-
sible to use the wheel rims from other vehi-
cles. This can also apply to wheel rims of the
same vehicle type.
The tightening torque of the wheel bolts
must be checked regularly with a properly
functioning torque wrench.

Tyre lettering and tyre type
Please refer to at the start of the chapter on page 328.
Fig. 186
International tyre lettering.