Spring VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Service Manual

Downloaded from www.Manualslib.com manuals search engine 48-28

11 - Adjusting screw with
lock nut, 60 Nm (44 ft
lb) Before removing, mark position of adjusting
bolt and lock nut on
housing Steering gear,
adjusting Page 48-24 12 - Pressure spring
13 - Pressure piece Mark installation
position
14 - Housing Check cylinder race for scoring, if necessary
replace steering gear
complete
15 - Inverted tube nut, 30
Nm (22 ft lb)
16 - O-ring Always replace Is not included in
repair kit - see Parts
catalog Page 28 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-33

- Mark position of adjusting screw and lock nut to
the housing (arrow) Note: - Screw lock nut together with adjusting screw Do not change position of adjusting screw to lock
nut when removing If necessary, remove adjusting screw together
with lock nut using tool 3115/6 Pressure piece/adjusting screw are slightly
stressed with slight spring pressure
1 - Ratchet (standard commercial) 2 - Adjusting screw Page 33 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-49
- Drive sealing ring in far enough sot that the groove for circlip in the housing is visible
- Install circlip - Remove adhesive tape - Remove assembly mandrel 3315/17 - Install hex nut for valve body and tighten, 30 Nm
(22 ft lb) with torque wrench SW 14 2 Note: - Install locking screw - Grease pressure piece and spring in housing in old position
- Install lock nut together with adjusting screw After tightening, the marking made during removal (arrow) on the adjusting nut and lock nut must
match If the toothed rod was replaced, before installing
the tie rods the steering gear must be readjusted Page 49 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-51

Power steering gear, adjusting with new
toothed rod If a new toothed rod was used, the steering play
should be adjusted according to the following
description.
- Drill a hole 5.1 mm in diameter in the center of the
adjusting screw (on the back side center)
- Thoroughly clean adjusting screw - Place toothed rod in center position (measure
toothed rod excess right and left)
- Install pressure piece and spring in housing if not
done yet
- Screw adjusting screw and lock nut far enough into the housing so that the markings match Page 51 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-62

Note: Do not change position of the adjusting screw
(arrow) Cover is stressed with slight spring pressure - Remove pressure piece 1 - Spreading pliers (standard commercial) Page 62 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-76
- Carefully slide bushing with roller bearing onto the
valve body.
- Drive bushing into the housing far enough so that
the groove for the circlip is visible.
- Install circlip. - Remove adhesive tape. - Remove installation mandrel 3315/17. - Install Torx screw into valve body and tighten to 35 Nm (26 ft lb). - Thread in locking screw, tighten to 30 Nm (22 ft lb)
and crimp at corner points.
- Grease pressure piece with AOF 063 000 04. - Install pressure piece, spring and washer in
housing.
- Install cover with adjusting screw. Adjust steering
gear after installation in vehicle. Page 76 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1