rear wheel suspension shaft VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Workshop Manual

Downloaded from www.Manualslib.com manuals search engine Suspension, Wheels, Brakes, Steering

00 - General, Technical data
Suspension, Wheels, Brakes, Steering
Technical data
Steering
Brakes
Wheels, tires
40 - Front suspension
Front Wheel Suspension, Shafts and Axle
Front suspension, servicing (Base suspension)
Sub-frame, stabilizer bar and control arm (Base suspension)
Ball joint, checking (Base and Plus suspension)
Reworking cap nut in side member (Base and Plus suspension)
Wheel bearing, suspension strut and drive shaft, removing and installing (Base
running gear)
Front suspension strut, servicing (Base and Plus suspension)
Front suspension, servicing (Plus suspension)
Sub-frame, stabilizer bar and control arm, removing and installing (Plus
suspension)
Ball joint, removing and installing (Plus running gear)
Wheel bearing and suspension strut, removing and installing (Plus suspension)
Drive shaft, removing and installing (Plus running gear)
Drive shaft, repairing
Outer constant velocity joint, checking
Inner constant velocity joint, checking
Drive shaft with tripod joint, repairing
Drive axle with triple-rotor joint, removing and installing
Drive axle with triple-rotor joint, servicing
Triple-rotor joint, disassembling
Triple-rotor joint, assembling
42 - Rear suspension
Rear Wheel Suspension, Shafts and Axle
Rear axle, servicing (vehicles with front wheel drive)
Reworking cap nut in side member (front wheel drive vehicles)
Suspension strut, disassembling and assembling (front wheel drive vehicles)
Wheel bearings, servicing
Drum brakes (front wheel drive vehicles), wheel bearings, servicing
Wheel bearings, servicing - disc brakes (front wheel drive vehicles)

Downloaded from www.Manualslib.com manuals search engine Rear axle, servicing (four wheel drive vehicles)
Rear drive shafts, servicing
Reworking cap nut in side member (four wheel drive vehicles)
Suspension strut, disassembling and assembling (four wheel drive
vehicles)
Wheel bearings, servicing - disc brakes (four wheel drive vehicles)
44 - Wheels, Tires, Wheel alignment
Vehicle alignment
Test requirements:
Vehicle alignment specifications (front wheel drive vehicles)
Vehicle alignment specifications (four wheel drive vehicles)
Front wheel camber, adjusting
Calculating the direction of travel:
45 - Anti-lock brake system
Anti-locking Brake System (ABS) and Anti-locking Brake System with
Electronic Differential Lock (ABS/EDL) Teves 04
Notes for repair work on ABS, ABS/EDL
Control module, removing and installing
Wheel speed sensor and rotor for speed sensor, removing and installing
Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock
(ABS/EDL), Teves 20 GI
Safety precautions
ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master
cylinder (Teves 20 GI), servicing
ABS hydraulic unit and ABS control module (Teves 20 GI), removing and
installing
Brake hydraulic system, bleeding and filling
Assembly overview - hydraulic unit, brake servo/brake master cylinder
Hydraulic unit, removing and installing
Brake Pedal Position Sensor, removing and installing
46 - Brakes - Mechanical components
Front brakes, servicing (Girling caliper)
Brake pads, removing and installing

Downloaded from www.Manualslib.com manuals search engine 40-4

6 - Control arm rear
mounting Installation position
Fig. 3 Pressing out and in
Fig. 4 7 - Hex bolt M 12 x 1.5 x 82 50 Nm (37 ft lb) and
turn 90 further 8 - Hex bolt M 12 x 1.5 x 65 70 Nm (52 ft lb) and
turn 90further 9 - Hex bolt M 12 x 1.5 x 78 70 Nm (52 ft lb) and
turn 90further 10 - Control arm front
mounting Pressing out Fig. 1 Pressing in Fig. 2 11 - Connecting link With rubber mounting Page 4 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-8
One of the embossed arrows points toward the
recess in the control arm and the kidney shaped
opening (arrow A) faces towards center of vehicle. Fig. 3 Control arm rear mounting, installation
position Note:
If bonded rubber bushing is tight because of
corrosion, cut rubber out, saw through steel casing
and drive bushing out. Fig. 4 Control arm rear mounting, pressing
out and in Page 8 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-12
Bolt/washer assemblies for sub-frame Securing point
Thread
Bolt
Part No.
Front sub-frame M12 x 1.5 M12 x 1.5 x 95 10.9
N 101 612.01 1)

Rear sub-frame M12 x 1.5 M12 x 1.5 x 95 10.9 N 101 612.01
Sub-frame bracket M10 M10 x 38 10.9 N 019 541.1
Engine front cross-member to side member M10 M10 x 75 10.9
N 904 078.01 1)
1)
These bolts are not listed in the parts catalog. They must be specially ordered. Page 12 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-28

5 - Control arm rear
mounting Installation position
Fig. 2 Pressing out and in
Fig. 3 6 - Control arm Elongated holes are
not for camber
adjustment!
7 - Air guide plate Secured to control arm by clip
8 - Control arm front
mounting Pressing out and in
Fig. 1 9 - Hex bolt M 12 x 1.5 x 78 70 Nm (52 ft lb) and
turn 90 further 10 - Hex bolt M 12 x 1.5 x 65 70 Nm (62 ft lb) and
turn 90 further 11 - Connecting link With rubber mounting Page 28 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-31
Note:
Before pressing in, coat with lubricant, e.g. soft soap. Fig. 1 Control arm front mounting, pressing
out and in One of the embossed arrows points toward the
recess in the control arm and the kidney shaped
opening -arrow -A- in mounting faces towards center
of vehicle. Fig. 2 Control arm rear mounting, installation
position Page 31 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-32
Fig. 3 Control arm rear mounting, pressing
out and in Fig. 4 Engine/transmission assembly,
supporting with 10-222 A and 10-222
A/3 Page 32 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-71
- Remove rear transmission mounting bolt (arrow). - Remove front engine mounting bolt (arrow). - Lift engine/transmission assembly - Loosen drive axle nut while vehicle is standing on
its wheels. Page 71 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 42-1

Rear Wheel
Suspension, Shafts
and Axle
Rear axle, servicing
(vehicles with front wheel
drive)
Note: The rear axle and wheel
bearings are identical on
Base and Plus suspension
versions. Welding and straightening
of the axle beam is not
permissible.
1 - Wheel bolt 110 Nm (81
ft lb)
2 - Self-locking hex nut, 70 Nm (52 ft lb) When tightening the
nut the axle beam
must be in the
horizontal position
(unladened vehicle
state)
3 - Hex bolt, 25 Nm (18 ft
lb)
4 - Suspension strut Removing and
installing Fig. 1 to Fig. 3 Disassembling and
assembling Page 42-9 Page 1 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1