turn signal VOLVO C70 CONVERTIBLE 2007 Owner´s Manual

2007 Volvo C70
1. All windows up/down68
2. Power windows
68
3. Door mirror button, driver's side
71
4. Door mirror adjustment control
71
5. Door mirror button, passenger's side
71
47 02 Instruments and controls
Instrument panel
Instrument panel
1. Speedometer
2. Turn signal, left
3. Warning symbol
See the following pages for additional information.
file:///K|/delme/2007_C70/07c70_02.htm (4 of 43)12/22/2006 9:15:42 PM

2007 Volvo C70
4. Information display
The display presents information and warning messages, the ambient tempe\
rature, and the clock, etc. When the
ambient temperature is between 23° and 36°F (-5° and +2°C)\
, a snowflake symbol is shown in the display. This
symbol serves as a warning for possible slippery road surfaces. Please n\
ote that this symbol does not indicate a fault
with your car. At low speeds, or when the car is not moving, the tempera\
ture readings may be slightly higher than the
actual ambient temperature.
5. Information symbol
See the next pages for additional information.
6. Turn signal, right
7. Tachometer
The tachometer shows engine speed in thousands of revolutions per minute\
(rpm). Do not drive continuously with the
needle in the red area of the dial, which indicates maximum allowable en\
gine rpm range. Instead, shift to a higher
gear or slow the vehicle down. The engine management system will automat\
ically prevent excessively high engines
speeds. This will be noticeable as a pronounced unevenness in engine spe\
ed.
8. Indicator and warning symbols
9. Fuel gauge
The fuel tank holds approximately 16.3 US gallons (62 liters). When a \
warning light in the gauge comes on, there are
approximately 2.1
48 02 Instruments and controls
Instrument panel
US gallons (8 liters) of fuel remaining in the tank.
10. Trip odometer reset button
The trip odometers are used to measure short distances. Press the button\
briefly to switch between the odometer for
the car's total mileage and the two trip odometers, T1 and T2. A long pr\
ess (more than 2 seconds) resets the currently
selected trip odometer.
11. Function display
This window displays information on functions such as the odometer, trip\
odometers, optional rain sensor, and cruise
control.
12. High beam indicator
13. Clock setting button
Turn the button to set the time.
14. Temperature gauge
file:///K|/delme/2007_C70/07c70_02.htm (5 of 43)12/22/2006 9:15:42 PM

2007 Volvo C70
1. Turn signal indicator for trailer (certain models)

If you are towing a trailer, this light will flash simultaneously with t\
he turn signals on the trailer. If the light does not
flash when signaling, one of the turn signals on the trailer or on the c\
ar are not functioning properly.
2. Parking brake applied

Parking brake applied This light is on when the parking brake (hand bra\
ke) is applied. The parking brake lever is
situated between the front seats. Always pull up this lever as far as po\
ssible when applying the parking brake.
NOTE
Canadian models are equipped with the second
symbol.
3. SRS warning light

If this light comes on while the car is being driven, or remains on for \
longer than approximately 10 seconds after the
car has been started, the SRS system's diagnostic functions have detecte\
d a fault in a seat belt lock or tensioner, a
front airbag, side impact airbag, and/or an inflatable curtain. Have the\
system(s) inspected by a trained and qualified
Volvo service technician as soon as possible.
file:///K|/delme/2007_C70/07c70_02.htm (10 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
1. Turn signals, lane change position
2. Turn signals, position for normal turns
3. High beam flash
4. Toggle between high and low beams, Home Safe lighting
Turn signals
When turning
l Move the lever as far up or down as possible (to position 2) to start \
the turn signals.
The turn signals will be cancelled automatically by the movement of the \
steering wheel, or the lever can be returned
to its initial position by hand.
When changing lanes
The driver can automatically flash the turn signals 3 times by:
l Moving the turn signal lever up or down to position 1 and releasing it. \
l Moving the lever up or down to position 2 and immediately back to its or\
iginal position.
NOTE
l This automatic flashing sequence can be interrupted by immediately movin\
g the lever in the opposite
direction.
l If the turn signal indicator flashes faster than normal, check for a bur\
ned-out turn signal bulb.
High/low beam headlights
Continuous high beams
1. Turn the ignition key to position II.
2. With the light switch (1) in position
, (see page 55) pull the turn signal lever toward the steering wheel (position
file:///K|/delme/2007_C70/07c70_02.htm (18 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
4) to toggle between high and low beams.
High beam flash
1. Turn the ignition key to position II.
2. Pull the turn signal lever to position
3. The high beams will remain on until the lever is released.
Home safe lighting
When you leave your car at night, you can make use of the home safe ligh\
ting function to illuminate the area in front
of the car.
1. Remove the key from the ignition switch.
2. Pull the direction indicator lever as far as possible towards the ste\
ering wheel (to position 4) and release it.
3. Exit the car and lock the doors.
The headlights and parking lights will illuminate and remain on for 30
1, 60 or 90 seconds. The time interval can be
changed according to your preferences by using the Personal Settings fun\
ction, see
page 72 for more information.
1Factory setting
58 02 Instruments and controls
Trip computer
The trip computer stores information gathered from several systems in yo\
ur car and has four menus (five on Canadian
models) that can be shown in the information display.
l MILES TO EMPTY TANK
l AVERAGE (average fuel consumption)
file:///K|/delme/2007_C70/07c70_02.htm (19 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
seconds until the frequency signal has been learned. The indicator light\
will flash slowly and then rapidly after several
seconds upon successful training. DO NOT release until the HomeLink indi\
cator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both buttons may be released. \
(The rapid flashing indicates successful
training.)
76 02 Instruments and controls
HomeLink® Universal Transceiver (option)
4. Press and hold the trained HomeLink button and observe the indicator \
light.
l If the indicator light is solid/continuous, training is complete and you\
r device should activate when the HomeLink
button is pressed and released.
l If the indicator light blinks rapidly for 2 seconds and then turns a sol\
id/continuous light, proceed with the following
training instructions for a rolling code device. A second person may mak\
e the following steps quicker and easier.
Please use a ladder or other device. Do not stand on your vehicle to per\
form the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, \
locate the "learn" or "smart" button (usually near
where the hanging antenna wire is attached to the unit). If there is di\
fficulty locating the training button reference the
garage door opener's manual or contact us.
6. Press and release the "learn" or "smart" button (the name and color \
of the button may vary by manufacturer).
NOTE
Once the button is pressed, there are 30 seconds in which to initiate th\
e next
step.
7. Return to the vehicle and firmly press and hold the trained HomeLink \
button for two seconds and release. Repeat
the "press/hold/release" sequence up to 3 times to complete the training\
process.
NOTE
During programming, your hand-held transmitter may automatically stop tr\
ansmitting. Continue to press and hold
the desired HomeLink button while you press and repress ("cycle") your\
hand-held transmitter every two seconds
until the frequency signal has been learned. The indicator light will fl\
ash slowly and then rapidly after several
seconds upon successful training. If necessary, follow steps 5-7 to comp\
lete the training for a rolling code device.
To train additional HomeLink buttons, begin with step two.
Rolling Code Programming
Rolling code garage door openers that are "code-protected" and manufactu\
red after 1996 may be determined by the-
following:
l Reference the garage door opener owner's manual for verification.
l The handheld transmitter appears to program the HomeLink Universal Trans\
ceiver but does not activate the garage
door.
file:///K|/delme/2007_C70/07c70_02.htm (41 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
94 04 Interior
Power retractable hard top
Raising or lowering the power retractable hard top
1. Turn the ignition key to position II, or start the engine if the vehi\
cle is parked outdoors.
2. Press the brake pedal.
3. Press and hold down the left button (1) to raise the power retracta\
ble hard top or the right button (2) to
lower it. Hold down the respective button until the top is completely ra\
ised or lowered.
Release the button when an audible signal sounds. The message ROOF OPEN or ROOF CLOSED will be
displayed.
CAUTION
l Please heed any messages that may appear in the information display whil\
e the top is in operation.
l Any windows that are closed will be opened approximately 4 inches (10 c\
m) while the power
retractable hard top is in operation. The windows will be automatically \
re-closed when the top is
completely raised or lowered.
WARNING
file:///K|/delme/2007_C70/07c70_04.htm (11 of 27)12/22/2006 9:15:45 PM\

2007 Volvo C70
If either of the remote controls is lost, the other must be taken with t\
he car to a Volvo retailer. As an anti-theft measure, the code of
the lost remote control must be erased from the system.
Each key blade has a unique code, which is used if new key blades are re\
quired. A maximum of six remote controls/key blades can
be programmed and used for one car.
Immobilizer (start inhibitor)
Each of the keys supplied with your car contains a coded transponder. Th\
e code in the key is transmitted to an antenna in the ignition
switch where it is compared to the code stored in the start inhibitor mo\
dule. The car will start only with a properly coded key. If you
misplace a key, take the other keys to an authorized Volvo retailer for \
reprogramming as an antitheft measure. USA - FCC ID: LTQWFS 125VO
This device complies with part 15 of the FCC rules. Operation is subject\
to the following condition: (1) This device may not
cause harmful interference, and (2) this device must accept any interf\
erence received, including interference that may cause
undesired operation.
Canada - IC: 3659A-WFS125VO
Operation is subject to the following conditions: (1) this device may \
not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation \
of the device.
CAUTION
Never use force on the narrow section of the remote control - this is wh\
ere the transponder is located. The car cannot be started if
the transponder is damaged.
109 05 Locks and alarm
Remote control and key blade
Remote control functions
1. Lock - Press the Lock button on the remote once to lock both doors, the trun\
k, the cabin storage compartments (compartment in
the doors, the rear side panels, and the ski hatch in the center of the \
rear seat backrest). The turn signals will flash twice to confirm
locking.
file:///K|/delme/2007_C70/07c70_05.htm (2 of 13)12/22/2006 9:15:47 PM

2007 Volvo C70
NOTE
The remote control will not lock or unlock the glove
compartment.
Double locking
If the car is locked with the remote control while the power retractable hard top is down, the double locking feature activates after
approximately 30 seconds. This means that the doors cannot be unlocked o\
r opened from inside the car.
NOTE
The double locking function can be temporarily disabled. See
page 118 for
instructions.
2. Unlock - Press the Unlock button on the remote once to unlock the driver's doo\
r. The turn signals will flash twice to confirm
unlocking.
After a short pause, press the Unlock button a second time within 10 sec\
onds to unlock the other doors and the trunk.
A long press (at least two seconds) opens all side windows.
NOTE
l The turn signals flash to confirm that the vehicle has been correctly lo\
cked/unlocked with the remote control. When locking the
vehicle, the turn signals will flash a confirmation only if all the door\
s are securely closed and locked. Flashing confirmation for
locking and unlocking may be customized in the vehicle's Personal settin\
gs menu. See
page 72 for more information.
l The two-step unlocking function can be changed so that one press of the \
Unlock button unlocks all of the doors and the trunk.
See Personal settings on
page 72 for more information.
l Automatic relocking: If the doors are unlocked, the locks will automatically reengage (re-\
lock) and the alarm will rearm after 2
minutes unless a door or the trunk has been opened.
l Automatic locking: When the car starts to move, the doors and trunk can be locked automat\
ically. This feature can be turned on
or off, see Personal settings on
page 72 for more information.
l Airbag deployment will automatically attempt to unlock the doors.
3. Approach lighting - As you approach the car:
Press the yellow button on the remote control to light the interior ligh\
ting, position/parking lamps, and license
110 05 Locks and alarm
Remote control and key blade
plate lighting and the lights in the door mirrors. These lights will swi\
tch off automatically after 30, 60 or 90 seconds. See the
Personal settings on
page 72 for information about adjusting the time setting.
4. Unlock trunk- Press the button once to disarm the alarm system and unlock only the t\
runk. After closing, the trunk will not
automatically relock. Press Lock to relock it and rearm the alarm.
NOTE
This function will unlock, but not pop open, the
trunk.
file:///K|/delme/2007_C70/07c70_05.htm (3 of 13)12/22/2006 9:15:47 PM

2007 Volvo C70
5. Panic alarm: - This button can be used to attract attention during emergency situat\
ions.
To activate the panic alarm, press and hold the red button for at least \
3 seconds or press it twice within 3 seconds. The turn signals
and horn will be activated.
The panic alarm will stop automatically after 30 seconds.
To deactivate, wait approximately 5 seconds and press the red button aga\
in.
NOTE
This button will NOT unlock the
car.
Weak battery in the remote control
When the battery begins to lose its charge, the Information symbol in th\
e instrument panel (see page 49) lights up and REMOTE
BATTERY LOW VOLTAGE is shown in the information display.
Replacing the battery in the remote control
If the range of the transmitter is noticeably reduced, this indicates th\
at the battery (type CR 2032, 3V) is weak and should be
replaced. To replace the battery:
1. Remove the key blade.
111 05 Locks and alarm
Remote control and key blade
2. Place the remote control with the keypad downward. Remove the screw (\
1) using a small slotted screwdriver.
3. Remove the cover.
4. Note how the + and - sides of the battery are positioned on the insid\
e of the cover. The plus side of the new battery (marked on the
battery) must face downward.
CAUTION
file:///K|/delme/2007_C70/07c70_05.htm (4 of 13)12/22/2006 9:15:47 PM