length VOLVO S60 TWIN ENGINE 2019 User Guide

SEATS AND STEERING WHEEL
}}
* Option/accessory.189
Move the passenger seat forward/rearwardby moving the control forward/rearward.
Change the backrest tilt of the passengerseat by moving the control forward/back-ward.

Related information
Manual front seats (p. 180)
Power* front seats (p. 181)
Adjusting the power* front seats (p. 181)
Storing positions for seats, mirrors and head-up display* (p. 182)
Using stored positions for seats, mirrors andhead-up display* (p. 183)
Adjusting front seat massage settings*(p. 185)
Adjusting* front seat cushion length (p. 185)
Front seat massage* settings (p. 184)
Adjusting front seat side bolster settings*(p. 186)
Adjusting front seat lumbar support* (p. 187)
Folding down the rear seat
backrests*
The rear seat backrest is split into two sections.The two sections can be folded forward individu-ally.
WARNING
Adjust the seat and ensure it locks intoposition before driving. Use caution whenadjusting the seat. Uncontrolled or care-less adjustments could lead to injury.
Long objects must always be securelytied down to help prevent injury or dam-age in the event of sudden braking.
Always turn off the engine and apply theparking brake when loading or unloadingthe vehicle.
Put the gear selector in P to help preventthe gear selector from being inadvertentlymoved.

CAUTION
When the backrest is folded down, make surethere are no objects in the rear seat, and theseat belts are not buckled. Otherwise there isa risk of damage to the upholstery.

STARTING AND DRIVING
* Option/accessory.443
Type approval for HomeLink®*19

FCC (USA) and IC (Canada)
This device complies with FCC rules part 15 andIndustry Canada RSS-210. Operation is subjectto the following two conditions: (1) This devicemay not cause harmful interference, and (2) Thisdevice must accept any interference that may bereceived including interference that may causeundesired operation.

WARNING
The transmitter has been tested and complieswith FCC and IC rules. Changes or modifica-tions not expressly approved by the partyresponsible for compliance could void theuser's authority to operate the device.20

Type approval for EU
Gentex Corporation hereby declares that
HomeLink® Model UAHL5 complies with theRadio equipment directive 2014/53/EU.
Wavelengths within which the radio equipmentoperates:
433.05MHz-434.79MHz <10mW E.R.P.
868.00MHz-868.60MHz <25mW E.R.P.
868.70MHz-868.20MHz <25mW E.R.P.
869.40MHz-869.65MHz <25mW E.R.P.
869.70MHz-870.00MHz <25mW E.R.P.
Certificate holder address: Gentex Corporation,600 North Centennial Street, Zeeland MI 49464,USA
For more information, see support.volvocars.com.
Related information
HomeLink®* (p. 440)
Compass*
An integrated compass21 in the upper right cor-ner of the rearview mirror shows the directionthe vehicle is traveling.
Rearview mirror with compass.
Eight different compass directions are shownwith the abbreviations: N (north), NE (northeast),E (east), SE (southeast), S (south), SW (south-west), W (west) and NW (northwest).

Related information
Activating and deactivating the compass*(p. 444)
Calibrating the compass* (p. 444)
19Certain markets only.20The term "IC:" before the certification/registration number only signifies that Industry Canada technical specifications were met.

||
AUDIO, MEDIA AND INTERNET
458
be displayed immediately. Album art is synchedwith the artist that you are currently listening to.

Ball game mode
This feature means that a main FM station (HD1)will broadcast live events, where the content ofthe programming is more important than soundquality, in analog mode only to help prevent thedelay between analog and digital broadcasting.The HD Radio symbol will be white during livebroadcasts and "Live" will be displayed next tothe symbol.

Benefits of digital broadcasting
Better sound (FM sounds near CD quality).
Some FM frequencies offer a greater num-ber of listening choices through multicasting(consisting of a frequency's main channeland any sub-channels that may also be avail-able on that particular frequency.)
When receiving a digital signal there is nomultipath disturbance or hisses/pops/crack-ling due to outside influences.

How HD Radio ™ Technology
broadcasting works
HD Radio works similarly to conventional radioand broadcasts of this type are available in manyareas of the United States. However, there are afew key differences:
Instead of transmitting one analogue signal,stations send out a bundled signal – bothanalog and digital.
An HD Radio receiver can receive both digi-tal and analog broadcasts. Depending on theterrain and location of the vehicle (which willinfluence the signal strength), the receiverwill determine which signal to receive.
Related information
Radio (p. 453)
Activating and deactivating the HD Radio™(p. 458)
HD Radio™ sub-channels (p. 459)
HD Radio™ limitations (p. 460)
Changing waveband and radio station(p. 454)
Searching for a radio station (p. 455)
Activating and deactivating the HD
Radio™
HD Radio is deactivated when the car leaves thefactory.
When listening to an HD Radio station and driv-ing through areas with weak HD signals (fringeareas), you may experience that the radio repeat-edly switches between analog/digital and digital/analog reception. If this happens, it may be desir-able to switch HD off.
Carry out the following to activate or deactivateHD Radio:
1.Drag down the top view and tap onSettings.
2.Press Media and FM Radio.
3.Press HD Radio FM to activate/deactivatethe function.
If HD radio is deactivated, the radio will be unableto receive digital broadcasts but it will continue tofunction as a conventional radio (analog FMreceiver). Please note that when HD is switchedoff, it will not be possible to tune in to sub-chan-nels.
Note that if you activate or deactivate HD Radioonly the selected wavelength band is affected.

Related information
HD Radio™ (p. 457)
HD Radio™ sub-channels (p. 459)

MAINTENANCE AND SERVICE
607
Replacing windshield wiper blades
The wiper blades help remove water from thewindshield. Along with the washer fluid, theyclean the glass and help improve visibility whiledriving. The wiper blades can be replaced.

Replacing wiper blades
1. Raise the wiper arms to the service position.Service position is activated/deactivated viathe function view in the center display whenthe car is stationary and the windshield wip-ers are not on.
2. Put the wiper blade in removal positionby folding it out from the wiper arm until itclicks.
3. Press and hold the button on the wiperblade attachment and pull the wiper blade
straight out , parallel with the wiper arm.
4.Slide in the new wiper blade until it clicksinto place.
5. Fold the blade back toward the arm until itclicks into place. The blade is no longer in itsremoval position and can once again bemoved.
6. Check to make sure the wiper blade issecurely in place.
7. Press the wiper blade back against the wind-shield.

Wiper blades come in varying lengths
NOTE
When changing wiper blades, make sure thatthe blades are of different lengths. The bladeon the driver's side is longer than the one onthe passenger side.
Related information
Using the rain sensor (p. 175)
Using the windshield and headlight washers(p. 177)
Using the rain sensor's memory function(p. 176)
Filling washer fluid (p. 609)
Windshield wipers in the service position(p. 608)
Using the windshield wipers (p. 175)
Wiper blades and washer fluid (p. 174)

SPECIFICATIONS
}}
615
Dimensions
The vehicle's length, height, etc. are shown inthe table.
Dimensionsmminches
AGround clearanceA1365.4
B Wheelbase2872 113,1
C Length4761 187.4
D Load length, floor,folded backrest1797 70.7
E Load length, floor 1005 39.6
FHeightB1437 56.6
Dimensionsmminches
GLoad height485 19,1
H Wheel track, front1603C
1600D
1593E
63.1C
63,0D
62,7E
I Wheel track, rear1603C
1600D
1593E
63.1C
63,0D
62,7E
Dimensionsmminches
JLoad width, floor 867 34,1
K Width1850 72.8