turn signal VOLVO S80 2011 Owner´s Manual

04 Comfort and driving pleasure
Adaptive Cruise Control (ACC)*
04

* Option/accessory, for more information, see Introduction.165
Standby mode due to action by the driverACC is temporarily deactivated and put in
standby mode:
•when the brakes are applied
•if the gear selector is moved to N
•if the accelerator pedal is depressed for
more than 1 minute.
NOTE
If the accelerator pedal is only depressed for
a short time, such as when passing another
vehicle, ACC is deactivated temporarily and
is reactivated when the pedal is released.
Automatic standby modeAdaptive cruise control is linked to other sys-
tems such as the stability and traction control
system (DSTC). If this system is not functioning
properly, adaptive cruise control is automati-
cally deactivated and will go into standby
mode.
In the event of automatic deactivation, an audi-
ble signal will sound and the message
Cruise
control Cancelled is shown in the display.
The driver must then intervene and adapt the
vehicle's speed to the surrounding traffic and
regulate the distance to the vehicle ahead.
An automatic switch to standby mode may be
caused if:
•the vehicle's speed falls below 20 mph
(30 km/h)
•the wheels lose traction
•brake temperature is high
•engine speed (rpm) is too low or too high
•the radar sensor is obstructed by, for
example, wet snow or rain.
Turning ACC off completely
A short press on in standby mode or a long
press in active mode turns ACC off completely.
The set speed and time interval are then
cleared from the system's memory and cannot
be resumed by pressing
.
The radar sensor and its limitations
In addition to being used by ACC, the radar
sensor is also used by Distance Alert (see
page 170) and Collision Warning with Auto-
brake (see page 173). This sensor is designed
to detect cars or larger vehicles driving in the
same direction as your vehicle, in the same
lane.
WARNING
Accessories or other objects, such as extra
headlights, must not be installed in front of
the grille.
Modification of the radar sensor could make
its use illegal.
The radar sensor's capacity to detect vehicles
ahead is impeded:
•if the radar sensor is obstructed and can-
not detect other vehicles, for example in
heavy rain, or if snow or other objects are
obscuring the radar sensor.
NOTE
Keep the area in front of the radar sensor
clean.
•if the speed of vehicles ahead is signifi-
cantly different from your own speed.

04 Comfort and driving pleasure
Adaptive Cruise Control (ACC)*
04

* Option/accessory, for more information, see Introduction.167
WARNING
•Adaptive Cruise Control is not a colli-
sion avoidance system. The driver is
always responsible for applying the
brakes if the system does not detect
another vehicle.
•Adaptive Cruise Control does not react
to people or animals, or small vehicles
such as bicycles and motorcycles. It
also does not react to slow moving,
parked or approaching vehicles, or sta-
tionary objects.
•Do not use Adaptive Cruise Control in
demanding driving conditions such as
city driving or other heavy traffic situa-
tions, in slippery conditions, when there
is a great deal of water or slush on the
road, during heavy rain or snow, in poor
visibility, on winding roads or on high-
way on- or off-ramps.
Fault tracing and actions
If the message Radar blocked See manual is
displayed, this means that the radar signals
from the sensor have been obstructed and that
a vehicle ahead cannot be detected.
This, in turn, means that the functions of the
ACC, Distance Alert, and Collision Warning
System with Auto-brake will not function.
The table lists possible causes for this mes-
sage being displayed, and suitable actions.
CauseAction
The surface of the radar in the grille is dirty or obstructed in some way.Clean the radar surface, or remove the object causing the obstruction.
Heavy rain or snow is interfering with the radar signals.No action possible. Heavy precipitation may affect the function of the
radar.

04 Comfort and driving pleasure
Adaptive Cruise Control (ACC)*
04
168* Option/accessory, for more information, see Introduction.
CauseAction
Swirling water or snow from the surface of the road may interfere with
the radar signals.No action possible. A very wet or snow-covered road surface may affect
the function of the radar.
The surface of the radar is clean but the message remains in the display.Wait a short time. It may take several minutes for the radar to detect that
it is no longer obstructed.
Symbols and messages in the display
SymbolMessageDescription
-Standby mode or active mode when no other vehicle has been detected.
-Active mode with a detected vehicle to which ACC is adapting speed/distance.
-Time interval while it is being set.
-Time interval after it has been set.
-Turn on DSTC to enable
CruiseACC cannot be put in active mode if the stability system DSTC's Spin control is switched off. See
page 156 for more information.
-Cruise control CancelledACC has been automatically switched off.
The driver must regulate the vehicle’s speed/distance to the vehicle ahead.
-Cruise control UnavailableACC cannot be put in active mode. This may be due to:
•high brake temperature
•the radar sensor is obstructed (by heavy rain, snow, etc.)

04 Comfort and driving pleasure
Collision warning with Auto-brake*
04
174* Option/accessory, for more information, see Introduction.
Brake SupportIf the risk of collision continues to increase after
the collision warning has been given, Brake
Support is activated. Brake Support prepares
the brake system to react quickly, and the
brakes are applied slightly. This may be expe-
rienced as a light tug.
If the brakes are applied quickly, full braking
effect will be provided, even if pressure on the
brake pedal is light.
Auto-brakeIf a collision is imminent and the driver has not
applied the brakes or begun to steer around the
vehicle, the auto-brake function is activated
without the driver pressing the brake pedal.
Limited brake force is applied to reduce the
vehicle’s speed when the collision occurs. The
driver must apply the brakes for full braking
effect.
WARNING
The auto-brake function cannot prevent a
collision but instead is intended to reduce
speed at the moment of impact. For full
braking effect, driver must apply the brakes.
NOTE
The auto-brake function is always on and
cannot be turned off.
Operation
Some settings are controlled from the center
console via a menu system.
On and offTo switch Collision Warning on or off, go into
the menu Car settings
Collision
warning settings and select On or Off. When
the engine is started, the setting that was
selected when it was switched off will be used.
When the engine is switched on, the Collision
Warning setting that was being used when it
was switched off will be the default setting.
Activating/deactivating warning signalsThe collision warning system’s audible and vis-
ual signals are activated automatically when
the engine is started if the collision warning
system is switched on.
The audible warning signal can be activated/
deactivated by selecting the alternative
Collision warning on or Collis'n warning
OFF
in Car settingsCollision warning
settings
Warning sound.
Setting a warning distanceThis setting determines the distance at which
the visual and audible warnings are triggered.
Select
Long, Normal or Short underCarsettings
Collision warning settings
Warning distance
The warning distance determines the level of
sensitivity used by the system. The warning
distance
Long provides an earlier warning.
Begin by using Long and if the system gives
too many warnings, try changing to Normal.
WARNING
•The setting Short should only be used
in situations where traffic is light and
moving at low speeds.
•Collision Warning alerts the driver to the
risk of a collision but this function can-
not reduce the driver’s reaction time.
•For Collision Warning to be as effective
as possible, it is recommended that Dis-
tance Alert be set to 4 or 5, see
page 170.

04 Comfort and driving pleasure
Driver Alert System*
04
180* Option/accessory, for more information, see Introduction.
Operating DAC
Certain settings can be made from the menu
system controlled from the center instrument
panel.
The current system status can be checked on
the trip computer’s display by using the but-
tons on the left steering wheel lever.
Thumb wheel. Turn this wheel until Driver
Alert is displayed. The second line shows
the alternatives Off, Unavailable, or [-----
], i.e., the number of bars.
READ button. Confirms and erases a mes-
sage in the display.
Activating DACIn the center instrument panel, go to Car
settings and select Driver Alert on.
The function is activated when the
vehicle exceeds a speed of 40 mph
(65 km/h). The display will show level
markings of 1–5 bars, where a low
number of bars indicates erratic driving. A high
number of bars indicates stable driving.
If the vehicle is being driven erratically, the
driver will be alerted by an audible signal and
the message Driver Alert, Time for a break is
displayed. The warning will be repeated after a
short time if the driving pattern remains the
same.
WARNING
•An alert should be taken seriously since
it is sometimes difficult for a driver to
realize that he/she is fatigued.
•In the event of a warning or if the driver
feels fatigued, stop as soon as possible
in a safe place and rest.
Symbols and messages in the display
SymbolMessageDescription
-Driver alert offThe function is not switched on.
-Driver alert
UnavailableThe vehicle’s speed is below 37 mph (60 km/h) or the road lacks clear marking lines.

04 Comfort and driving pleasure
Driver Alert System*
04
182* Option/accessory, for more information, see Introduction.
Lane Departure Warning (LDW)–
introduction
This function is designed to help reduce the
risk of accidents in situations where the vehicle
leaves its lane and there is a risk of driving off
the road or into the opposite lane. LDW con-
sists of a camera that monitors the lane’s side
marker lines. The driver is alerted by an audible
signal if the vehicle crosses a side marker line
or the road’s center dividing line.
Operation and function
LDW can be switched on or off by pressing the
button on the center console. A light in the but-
ton illuminates when the function is on.
The trip computer display shows
Lane Depart
Warn Unavailable when the function is in
standby mode.
When LDW is in standby mode, the function is
activated automatically after the camera has
monitored the road’s side marker lines and the
vehicle’s speed exceeds 40 mph (65 km/h).
Lane Depart Warn Available will be dis-
played.
If the camera can no longer monitor the road’s
side marker lines, or if the vehicle’s speed fallsbelow 37 mph (60 km/h), LDW will return to
standby mode and
Lane Depart Warn
Unavailable will be displayed.
If the vehicle unexpectedly crosses the lane’s
left or right side marker lines, the driver will be
alerted by an audible signal.
No warning signal will be given in the follow-
ing situations:
•The turn signal is being used
•The driver’s foot is on the brake pedal1
•The throttle pedal is pressed quickly
•If the steering wheel is moved quickly
•In sharp turns that cause the vehicle’s
body to sway.
See page 176 for information on the camera’s
limitations.
WARNING
The driver will only be warned once for each
time the wheels cross a marker line. No
alarm will be given if a marker line is
between the wheels.
1A warning will be given even when Increased sensitivity has been selected.

07 Maintenance and specifications
Replacing bulbs
07
260* Option/accessory, for more information, see Introduction.
Introduction
All bulb specifications are listed on page 265.
The following bulbs should only be replaced by
a trained and qualified Volvo service techni-
cian:
•Dome lighting
•Reading lights
•Glove compartment lighting
•Footwell lighting
•Turn signals in the door mirrors
•Approach lighting in the door mirrors
•Brake lights
•Active Bending Lights and LED bulbs
NOTE
For information regarding any other bulbs
not mentioned in this section, please con-
tact your Volvo retailer or a trained and
authorized Volvo service technician.
WARNING
•Active Bending Lights* – due to the high
voltage used by these headlights, these
bulbs should only be replaced by a
trained and qualified Volvo service tech-
nician.
•Turn off the lights and remove the
remote key from the ignition before
changing any bulbs.
Headlight housing
G010325
WARNING
•The engine should not be running when
changing bulbs.
•If the engine has been running just prior
to replacing bulbs in the headlight hous-
ing, please keep in mind that compo-
nents in the engine compartment will be
hot.
The entire headlight housing must be lifted out
when replacing all front bulbs.
CAUTION
Never touch the glass of bulbs with your fin-
gers. Grease and oils from your fingers
vaporize in the heat and will leave a deposit
on the reflector, which will damage it.

07 Maintenance and specifications
Replacing bulbs
07

263 Parking lights
G021749
1. Remove the headlight housing from the
vehicle (see page 260).
2. Remove the cover over the bulbs (see
page 261).
3. To access the bulb, first remove the high
beam bulb.
4. Pull the wire to withdraw the bulb holder.
5. Remove the burned out bulb and install a
new one. It can only be secured in one
position.
6. Press the bulb holder into the socket and
press until it clicks into place.
7. Put the cover back into position and rein-
stall the headlight housing.
Turn signals
G021750
1. Remove the headlight housing from the
vehicle (see page 260).
2. Remove the round cover by pulling the tab
until the cover comes off.
3. Pull out the holder to access the bulb.
4. Remove the burned out bulb by pressing it
in slightly and turning out before pulling it
out. Press a new bulb into the socket.
5. Press the bulb holder into the socket and
press until it clicks into place.
6. Press the cover until it clicks into position.
7. Reinstall the headlight housing.
Side marker lights
NOTE
Before starting to replace a bulb, see
page 260.
G021751
1. Remove the headlight housing from the
vehicle (see page 260).
2. Remove the round cover.
3. Pull the wire to withdraw the bulb holder.
4. Pull out the burned out bulb and install a
new one. It can only be secured in one
position.
5. Press the bulb holder into the socket and
press until it clicks into place.
6. Press the cover until it clicks into position.

08 Specifications
Overview of information and warning symbols
08

* Option/accessory, for more information, see Introduction.299
SymbolDescriptionPag
e
High beam indicator72
Left turn signal indica-
tor72
Right turn signal indi-
cator72
ACanadian models
Other information symbols
SymbolDescriptionPa
ge
Adaptive Cruise Con-
trol *163,
168
Adaptive Cruise Con-
trol *163,
168
Adaptive Cruise Con-
trol *, Distance Alert*163,
168,
170
Adaptive Cruise Con-
trol *, Distance Alert*163,
168,
170
SymbolDescriptionPa
ge
Adaptive Cruise Con-
trol *163,
168
Adaptive Cruise Con-
trol *, Distance Alert*163,
168,
170
Adaptive Cruise Con-
trol *, Distance Alert*163,
168,
170
Adaptive Cruise Con-
trol*163,
168
Radar sensor*165
Camera*176
SymbolDescriptionPa
ge
Collision Warning with
Auto-brake*,177
Driver Alert System*179
Active Bending Lights
(ABL)*90
Fuel filler door (arrow
indicates it is on right
side of vehicle)72
Rain sensor*95
Driver Alert System*180
Driver Alert System*,
Lane Departure Warn-
ing*182
Driver Alert System*,
Lane Departure Warn-
ing*182

09 Index
09
308
Stability system...............................156, 157
indicator light........................................ 73
Starting the engine..................................108
with keyless drive...............................108
Starting the vehicle
after a crash (crash mode)....................35
Start inhibitor (immobilizer)........................ 53
Steering wheel
adjusting............................................... 88
horn....................................................... 88
keypad.................................. 88, 122, 134
Stone chips, touching up......................... 284
Storage spaces........................................ 196
Studded tires........................................... 235
Sunroof (moonroof).................................. 103
Sun shade.................................................. 99
Supplemental restraint system.................. 21
warning light......................................... 74
Symbols, overview................................... 298
T
Temporary spare tire............................... 236
Three-way catalytic converter................. 211Tire designations.....................................229
Tire Pressure Monitoring System....246, 247
indicator light........................................ 73
Tires.........................................................222
age...................................................... 222
changing from summer to winter........ 223
glossary of terms................................ 231
improving economy............................ 222
inflation pressure................................ 225
inflation pressure tables.............227, 228
load ratings......................................... 226
rotation............................................... 223
snow...................................................235
spare................................................... 236
specifications...................................... 226
speed ratings...................................... 226
storing................................................. 223
studded............................................... 235
tire pressure monitoring system......... 246
tread wear indicator............................ 224
uniform tire quality grading................. 234
Top tether anchors (child restraint sys-
tems).......................................................... 46
Touching up paint.................................... 284
Towing a trailer................................216, 217
trailer hitch.......................................... 217
Towing the vehicle........................... 218, 219Traction control........................................ 156
Trailer towing...................................216, 217
trailer hitch.......................................... 217
Transmission
general description.....................112, 113
oil........................................................ 296
shiftlock override................................ 113
Tread wear indicator................................ 224
Trip computer.......................................... 154
Trip odometers.......................................... 76
Trips, long distance................................. 205
Trunk
changing bulbs................................... 265
driving with it open.............................204
Turn signals............................................... 92
changing bulbs................................... 263
indicator lights...................................... 73
U
Uniform Tire Quality Grading...................234
Unlocking the vehicle..........................54, 63
Upholstery care....................................... 283