headlights VOLVO V90 1998 Owners Manual
[x] Cancel search | Manufacturer: VOLVO, Model Year: 1998, Model line: V90, Model: VOLVO V90 1998Pages: 175, PDF Size: 4.45 MB
Page 22 of 175
1998 Volvo S90
Chapter 2 - Instruments, switches and controlsInstruments, switches and controls
pg. 14
Instruments, switches and controls pg. 15
Shiftlock
When your car is parked, the gear selector is
locked in the (P)ark position. To release the
selector from this position, turn the ignition key
to position II (or start the engine), depress the
brake pedal, press the button on the front side of
the gear selector and move the selector from (P)
ark.
If it is necessary to manually override the
Shiftlock system:
l Turn the starting (ignition) key to position
I
l Press firmly on the OVERRIDE" button
located near the base of the gear selector.
l While holding the override button down,
move the gear selector from the (P)ark
position.
Keylock
Some of the items below are available on certain
models only.
1
Air vent...pg. 25
2
Headlights, parking lights...pg. 20
3
Rear fog light...pg. 22
4
Front fog lights...pg. 22
5 Space for additional equipment
6
Power antenna (sedans only)...pg. 22
7
Instruments...pg. 15-17
8
Electrically operated sun roof...pg. 23,
Electrically operated sun roof...pg. 49
9
Heated rear window/side door mirrors...pg. 23
10
Hazard warning flasher...pg. 23
11
Central lock switch...pg. 23
12
Air vents...pg. 25
13
Heating and ventilation...pg. 25-27
14
Passenger's side SRS (air bag)...pg. 6
15
Audio system...pg. 131
file:///K|/ownersdocs/1998/1998_SV90/98S90_014.htm (1 of 3)12/30/2006 \
1:52:36 PM
Page 27 of 175
1998 Volvo S90
Anti-lock Brake
System (ABS)
If the warning lamp lights up
there is a malfunction of the
ABS system (the standard
braking system will however
function). The vehicle should be
driven to a Volvo retailer for
inspection.
See page 67 for additional
information.
Canadian models are equipped
with this warning light:
Mode "W" engaged
The lamp will light up when the
Winter/Wet mode is engaged.
If the warning lamp begins to
flash,this means that there is a
fault in the automatic gearbox.
Contact your Volvo retailer.
Supplemental
Restraint System
If the light comes on (or stays
on after the vehicle has started),
the SRS diagnostic system has
detected a fault. Drive to an
authorized Volvo retailer for an
inspection of the system. See
the SRS section for more
information.
Service reminder
indicator
This light will come on at
10,000 mile (16,000 km)
intervals. It is a reminder to the
driver that the 10,000 mile
(16,000 km) service interval has
been exceeded. The light will
stay on 2 minutes after start
until reset by the servicing
retailer.
Coolant level sensor
If the light comes on while
driving, the coolant level is low.
The coolant level in the
expansion tank should be
checked immediately and
topped off if necessary. The
cooling system should be
inspected by an authorized
Volvo retailer.
Turn signal indicators-
trailer (certain models)
When towing a trailer, this light
will flash simultaneously with
the turn signals on the trailer. If
the light does not flash when
signaling, neither the trailer's turn
signals nor the car's turn signals
are functioning.
Bulb failure warning
light
The light will come on if any of
the following bulbs are defective:
one of the low beam headlights
one of the tail lights
one of the brake lights when the
brake pedal is depressed.
Check the fuse and bulb.
See sections titled "Replacing
bulbs" and "Fuses".
Lighting, Turn signals pg. 20
file:///K|/ownersdocs/1998/1998_SV90/98S90_017.htm (3 of 7)12/30/2006 \
1:52:36 PM
Page 28 of 175
1998 Volvo S90
Headlights and parking lights
All lights off *
Parking lights on **
Headlights and parking lights are on if
starting (ignition) switch is in position I or II. If
the headlight switch is in position
all lights
will go out when starting switch is switched off.
With the headlight switch in position
the
parking lights will stay on (headlights off) with
the daytime running light switch (A) in position
.
The high beams can only be switched on if the
headlight switch is in position
.
Switch from high to low beams, and vice versa,
by moving the turn signal switch lever on the left
side of the steering column towards the steering
wheel.
*Models equipped with daytime running lights:
The low beams, tail lights, parking lights and
license plate lights will come on automatically
when the ignition is switched on.
Automatic daytime running lights
NOTE: The daytime running light function may
only be disabled (turned off) in the U.S. -
Canadian law mandates the use of daytime
running lights.
Screw A in the illustration (available on U.S.
models only) is used to control the automatic
daytime running lights when the headlight switch
is in position 0. To adjust, press in the screw with
a small screwdriver and turn to one of the
following positions:
Automatic daytime
running lights
Automatic daytime
running lights
** The daytime running
lights will also function when
the headlight switch is in
Turn signals
1 Lane change position: In maneuvers such as
lane changing, the driver can flash the turn signals
by moving the turn signal lever to the first stop
and holding it there. The lever will return to the
neutral position when released.
2 Signal lever engaged for normal turns
3 High beam/low beam switch (headlights on)
Move the lever towards the steering wheel and
release it.
Headlight flasher (headlights off)
Move the lever towards the steering wheel.
The headlight high beam will be on until the lever
is released.
NOTE:Defective turn signal bulbs will cause turn
signal indicator and remaining signal lights to
flash more rapidly than normal.
file:///K|/ownersdocs/1998/1998_SV90/98S90_017.htm (4 of 7)12/30/2006 \
1:52:36 PM
Page 29 of 175
1998 Volvo S90
position and switch A is in this position.
All lights off (daytime running light function
disabled)
Winshield wipers/washers, Ignition switch pg. 21
Windshield wipers/washers
1 Intermittent wiper.
With switch in this position, the wipers will
sweep approximately every seventh second.
2 "Single sweep" position.
Switch returns automatically when released
3 Wipers, low speed.
4 Wipers, high speed
5 Windshield wiper/washer, headlight
wiper/washer (certain models)
The wiper will make 2-3 complete sweeps
across the windshield and headlights after
lever is released.
Starting
(ignition)
switch/
steering
wheel lock
The steering
wheel lock
might be under
tension when
the car is
parked. Turn
the steering
wheel slightly
to free the ignition key.
In order to reduce car
theft, make sure the
steering wheel lock is
engaged before leaving
the car.
Achime will sound if the
starting key is left in the
ignition lock and the
front door on the driver's
side is opened. 0 Locked position:
remove the key to lock the
steering wheel.
WARNING:
Never turn the key to
position 0 while driving or
when the car is being
towed.
I Intermediate position:
Certain accessories/radio,
etc. on, daytime running
lights off.
II Drive position:
Key position when engine is
running.
III Starting position:
Release the key when the
engine start.
The key returns
automatically to the Drive
position.
*The gear selector must be
in the (P)ark position before
the key can be removed
from the ignition switch.
Fog lights, Instruments illumination, Steering wheel adjustment, Power antenna
pg. 22
file:///K|/ownersdocs/1998/1998_SV90/98S90_017.htm (5 of 7)12/30/2006 \
1:52:36 PM
Page 30 of 175
1998 Volvo S90
A - Rear fog light*
The indicator light in the
instrument panel will light
up when the rear fog light
is on. This fog light is
considerably brighter than
the normal tail light and
should be used only when
the atmospheric
conditions, such as fog,
rain, snow, smoke or dust
reduce the daytime or
nighttime visibility of
other vehicles to less than
500 ft (150 meters).
*By design, there is one
rear fog light only, located
in the driver's side tail light
cluster.
B- Instrument
illumination
To increase the brightness,
rotate the switch upward.
To decrease the brightness,
rotate the switch
downward.
C- Front fog lights
The indicator light in the
switch will light up when
the front fog lights are on.
The front fog lights will
only function when the low
beam headlights are on.
NOTE:Local regulations
governing the use of fog
lights may vary.
D- Power antenna (sedans only)
This button can be used to lower the antenna
when, for example, you are listening to a tape or
CD, or when you are driving into a low-roof
garage or car wash. CAUTION: The antenna must be lowered
before washing the car in an automatic car wash. E- Steering
wheel adjustment
The steering wheel
can be adjusted to 3
different positions.
Move the control on
the left side of the
steering column
downward and hold
it in place. Adjust
the steering wheel
to the position
desired. Release the
control and check
that the steering
wheel is locked in
position.
WARNING!Do
not adjust the
steering wheel
while driving.
file:///K|/ownersdocs/1998/1998_SV90/98S90_017.htm (6 of 7)12/30/2006 \
1:52:36 PM
Page 46 of 175
1998 Volvo S90
Rear-view mirror
A Normal position
B Night position,
reduces glare from
following headlights
Electrically-operated side-view
mirrors
The control switches are located in the
driver's door armrest.
A Horizontal adjustment
B Vertical adjustment
CAUTION: Never use ice scrapers
made of metal as they can easily
scratch the mirror surface.
WARNING!The mirrors should
always be adjusted prior to driving.
Objects seen in the wide-angle right
side-view mirror are closer than they
appear to be.
Vanity mirrors
The vanity mirrors are located on both
front sun visors.
The lamps light up when the covers are
opened.
Interior light, Rear reading lights pg. 36
file:///K|/ownersdocs/1998/1998_SV90/98S90_031.htm (5 of 6)12/30/2006 \
1:52:39 PM
Page 91 of 175
1998 Volvo S90
Chapter 6 - (cont.)
Replacing bulbs
pg. 81
Replacing bulbs
The method for replacement of bulbs in
the various lighting units is shown on the
following pages. Make sure when
installing bulbs, that the guide pin on the
socket fits into its corresponding recess.
When installing Halogen bulbs, do not
touch the glass with your fingers because
grease, oil or any other impurities can be
carbonized onto the bulb and damage the
reflector.
Use bulbs of correct type and voltage.
Failure to do so could cause the bulb
failure warning light to activate.
NOTE: Turn the ignition and light
switch off before replacing any bulbs.
Headlights (high/low beams)
1. Press the protruding tabs on the plastic
cover and pull out towards the fender.
2. Turn the bulb and connector 1/4 turn
counterclockwise and remove.
3. Remove the connector from the bulb.
4. Press a new bulb into the connector
without touching the bulb itself.
5. Reinsert the bulb into the headlight
housing and turn 1/4 turn clockwise until
the unit seats properly.
6. Reinstall the plastic cover.
Bulb Power US Bulb No.
High beam 70W HB3/9005
Low beam 60W HB4/9006
Headlight adjustment
The height of the headlight beams can be
adjusted according to vehicle load. The
headlights should be re-aimed if heavy
loads are carried in the trunk/cargo area or
rear seat, or when towing a trailer.
To adjust the headlights:
Park the car on a level surface and open
the hood.
The headlights are equipped with a level
which can be seen by looking through the
clear "window" on the top of the headlight
lens.
Turn the height adjustment knob (A) until
the bubble in the level aligns with within
the marking lines on the level.
Lateral headlight adjustment (B) should
only be carried out by an authorized
Volvo retailer. This setting should be
preset to "0".
Replacing bulbs pg. 82
file:///K|/ownersdocs/1998/1998_SV90/98S90_081.htm (1 of 6)12/30/2006 \
1:52:45 PM
Page 135 of 175
1998 Volvo S90
Electrical system
12 V, negative ground.
Voltage-controlled generator. Single-wire system
with chassis and engine used as conductors.
Battery
Voltage 12 V
Capacity 600 A/125 min
The battery contains corrosive and poisonous acids.
It is of the utmost importance that old batteries are
disposed of correctly. Your Volvo retailer can assist
you in this matter.
Generator
Rated output 1400 W (certain models: 1680 W)
max. current 120 Amp (certain models: 120 Amp)
Bulbs
Bulb Trade
No. Power
Socket No.
of
bulb
Headlights HBI/9004 65/45 W – 2
Parking
lights,
turn
signals,
front 1157 N.
A.
21/5
W/24/2.2 cp BAY
15
2
turn
signals,
rear 1156
21W/32cp BA
15s 2
Tail lights 2x67 5W/4cp BA
15s 2
Brake
light 1156
21 W/32cp BA
15s 2*
file:///K|/ownersdocs/1998/1998_SV90/98S90_125.htm (2 of 7)12/30/2006 \
1:52:51 PM
Page 143 of 175
1998 Volvo S90
Anti-theft code
The radio features anti-theft
circuitry. If the set is removed
from the vehicle or if the
battery power is disconnected, a
special code must be entered to
enable operation of the set.
Refer to the radio code card
supplied with your vehicle or
ask your retailer for the
correct code.
When the car is parked with
ignition key removed the anti-
theft LED will flash. To enter the code
After installation or when the
set has been disconnected from
power, the set displays "CODE"
when it is switched on.
Enter the 4-digit code using the
preset buttons.
If the correct code is entered the
set is entered the set is ready to
use.
If you enter an incorrect code
you must enter the correct code
again from the beginning.
Incorrect code
If an incorrect code has been
entered "rPt" is displayed. Enter
the correct code. After three
unsuccessful coding attempts the
set will lock and remain locked
for two hours.
"OFF" is displayed.
During this waiting period:
l the battery must be connected
l the ignition key must be
turned to position I
l the unit must be turned on
Make sure the headlights are
turned off to help prevent battery
drain (please refer to page 20 for
information on turning the
headlights off).
Enter the code again once this
time has elapsed.
Radio SC-813 pg. 134
file:///K|/ownersdocs/1998/1998_SV90/98S90_131.htm (3 of 6)12/30/2006 \
1:52:52 PM
Page 154 of 175
1998 Volvo S90
Anti-theft code
The radio features anti-theft
circuitry. If the set is removed
from the vehicle or if the
battery power is disconnected, a
special code must be entered to
enable operation of the set.
Refer to the radio code card
supplied with your vehicle or
ask your retailer for the
correct code.
When the car is parked with
ignition key removed the anti-
theft LED will flash. To enter the code
After installation or when the
set has been disconnected from
power, the set displays "CODE"
when it is switched on.
Enter the 4-digit code using the
preset buttons.
If the correct code is entered the
set is entered the set is ready to
use.
If you enter an incorrect code
you must enter the correct code
again from the beginning.
Incorrect code
If an incorrect code has been
entered "EEEE" is displayed.
Enter the correct code. After
three unsuccessful coding
attempts the set will lock and
remain locked for two hours.
"OFF" is displayed.
During this waiting period:
l the battery must be connected
l the ignition key must be
turned to position I
l the unit must be turned on
Make sure the headlights are
turned off to help prevent battery
drain (please refer to page 20 for
information on turning the
headlights off).
file:///K|/ownersdocs/1998/1998_SV90/98S90_145.htm (2 of 6)12/30/2006 \
1:52:53 PM